[f-nsp] New MG8 switch blade BIMG8-10Gx4-v6-A CARD_STATE_INTERACTIVE

[Dominic Douglas]

Hi Justin,

I saw your problem with the XMR 10G blade, but the problem is harder then I
expected.

Lets go:

1. Removed blade from slot 2.
2. Sh mod:
S2: Configured as BIMG8-10Gx4-v6 4-port 10GbE IPv4/v6 Module

Log:
Nov 18 14:20:17:N:Module was removed from slot 2

But the slot is already configured with the right module. I will remove the
config and reconfigure it:

3. (config)#no mod 2 bimg8-v6-10g-4-port
4. (config)#module 2 bimg8-v6-10g-4-port
5. Sh mod:
S2: Configured as BIMG8-10Gx4-v6 4-port 10GbE IPv4/v6 Module

6. Insert module:

S2: Invalid Module  CARD_STATE_DOWN (7)  (previous state =
CARD_STATE_SW_LOADED)

End after the module startup:

S2: BIMG8-10Gx4-v6-A 4-port 10GbE IPv4/v6 Module (OACL)
CARD_STATE_INTERACTIVE    0

It might be a bigger problem. This (new) module is an A module:

BIMG8-10Gx4-v6-A

Our other modules:

M1 (upper): BIMG8-MR Management Module     Active
M2 (lower):
F1: BIMG8-SFM Switch Fabric Module         Active
S1:
S2: BIMG8-10Gx4-v6-A 4-port 10GbE IPv4/v6 Module (OACL)
CARD_STATE_INTERACTIVE    0
S3:
S4:
S5:
S6:
S7: BIMG8-1Gx40-SFP-v6 40-port 1 GbE IPv4/v6 Module (IPv6+OACL)
CARD_STATE_UP    40


Extra logging:

Nov 18 14:26:07:N:Module 2 is reset by mgmt (reason: boot to interactive
mode)
Nov 18 14:25:38:N:Module was inserted to slot 2
Nov 18 14:20:17:N:Module was removed from slot 2
Nov 18 13:36:35:N:Module 2 is reset by mgmt (reason: boot to interactive
mode)
Nov 18 13:36:10:N:Module 2 is reset by mgmt (reason: CLI command)
Nov 18 13:24:17:N:Module 2 is reset by mgmt (reason: boot to interactive
mode)
Nov 18 13:23:48:N:Module 2 is reset by mgmt (reason: lp sync during booting)
Nov 18 13:22:19:N:Module was inserted to slot 2


The module is forced to interactive mode by the management. It might be a
software problem..

Kind regards,

Dominic







On Thu, Nov 18, 2010 at 3:17 PM, Justin Suyk - Signet BV <jsuyk at signet.nl>wrote:

>  Hi,
>
> We had to remove the blade before changing the config.
> So :
>
> 1. remove module
> 2. remove the blade config (no module ... bi-...)
> 3. config the blade
> 4. insert the blade
> 5. get a beer
>
>
> Regards,
> Signet bv
>
>
> Justin Suyk
>
> T 040 - 707 4 907
> F 040 - 707 4 909
> Kvk 17089930
>
>
>
> On 11/18/2010 03:11 PM, Dominic Douglas wrote:
>
>
> *Hi All,
>
> We do have a problem with one of our MG8 switches. We've added a new
> BIMG8-10Gx4-v6-A blade, but after configuration the blade will not recover
> from CARD_STATE_INTERACTIVE.
>
> S2: BIMG8-10Gx4-v6-A 4-port 10GbE IPv4/v6 Module (OACL)
> CARD_STATE_INTERACTIVE    0   000c.db27.4560
>
> Steps taken:
>
> 1. Reset module.
> 2. Set type to the slot port.
> 3. Turn on/off module.
>
> Unfortunately we can't find any logs about the new blade, only the current
> state: **CARD_STATE_INTERACTIVE.
>
> Kind regards,
>
> Dominic
> **
>
> *
>
>
> _______________________________________________
> foundry-nsp mailing listfoundry-nsp at puck.nether.nethttp://puck.nether.net/mailman/listinfo/foundry-nsp
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://puck.nether.net/pipermail/foundry-nsp/attachments/20101118/480fddfe/attachment.html>