[f-nsp] New MG8 switch blade BIMG8-10Gx4-v6-A CARD_STATE_INTERACTIVE

[Remco Bressers]

What happens if you login to the card itself (# rconsole 2) and reboot
the thing? You should see the boot log and reason why the card won't
work. Are the software versions OK?


-- 
Regards,
Signet bv


Remco Bressers

T 040 - 707 4 907
F 040 - 707 4 909
E rbressers at signet.nl



On 11/18/2010 03:49 PM, Dominic Douglas wrote:
> Hi Justin,
> 
> I saw your problem with the XMR 10G blade, but the problem is harder
> then I expected.
> 
> Lets go:
> 
> 1. Removed blade from slot 2.
> 2. Sh mod:
> S2: Configured as BIMG8-10Gx4-v6 4-port 10GbE IPv4/v6 Module
> 
> Log:
> Nov 18 14:20:17:N:Module was removed from slot 2
> 
> But the slot is already configured with the right module. I will remove
> the config and reconfigure it:
> 
> 3. (config)#no mod 2 bimg8-v6-10g-4-port
> 4. (config)#module 2 bimg8-v6-10g-4-port
> 5. Sh mod:
> S2: Configured as BIMG8-10Gx4-v6 4-port 10GbE IPv4/v6 Module
> 
> 6. Insert module:
> 
> S2: Invalid Module  CARD_STATE_DOWN (7)  (previous state =
> CARD_STATE_SW_LOADED)
> 
> End after the module startup:
> 
> S2: BIMG8-10Gx4-v6-A 4-port 10GbE IPv4/v6 Module (OACL) 
> CARD_STATE_INTERACTIVE    0  
> 
> It might be a bigger problem. This (new) module is an A module:
> 
> BIMG8-10Gx4-v6-A
> 
> Our other modules:
> 
> M1 (upper): BIMG8-MR Management Module     Active
> M2 (lower):
> F1: BIMG8-SFM Switch Fabric Module         Active
> S1:
> S2: BIMG8-10Gx4-v6-A 4-port 10GbE IPv4/v6 Module (OACL) 
> CARD_STATE_INTERACTIVE    0 
> S3:
> S4:
> S5:
> S6:
> S7: BIMG8-1Gx40-SFP-v6 40-port 1 GbE IPv4/v6 Module (IPv6+OACL) 
> CARD_STATE_UP    40
> 
> 
> Extra logging:
> 
> Nov 18 14:26:07:N:Module 2 is reset by mgmt (reason: boot to interactive
> mode)
> Nov 18 14:25:38:N:Module was inserted to slot 2
> Nov 18 14:20:17:N:Module was removed from slot 2
> Nov 18 13:36:35:N:Module 2 is reset by mgmt (reason: boot to interactive
> mode)
> Nov 18 13:36:10:N:Module 2 is reset by mgmt (reason: CLI command)
> Nov 18 13:24:17:N:Module 2 is reset by mgmt (reason: boot to interactive
> mode)
> Nov 18 13:23:48:N:Module 2 is reset by mgmt (reason: lp sync during booting)
> Nov 18 13:22:19:N:Module was inserted to slot 2
> 
> 
> The module is forced to interactive mode by the management. It might be
> a software problem..
> 
> Kind regards,
> 
> Dominic
> 
> 
> 
> 
> 
> 
> 
> On Thu, Nov 18, 2010 at 3:17 PM, Justin Suyk - Signet BV
> <jsuyk at signet.nl <mailto:jsuyk at signet.nl>> wrote:
> 
>     Hi,
> 
>     We had to remove the blade before changing the config.
>     So :
> 
>     1. remove module
>     2. remove the blade config (no module ... bi-...)
>     3. config the blade
>     4. insert the blade
>     5. get a beer
> 
> 
>     Regards,
>     Signet bv
> 
> 
>     Justin Suyk
> 
>     T 040 - 707 4 907
>     F 040 - 707 4 909
>     Kvk 17089930
> 
> 
> 
>     On 11/18/2010 03:11 PM, Dominic Douglas wrote:
>>
>>     *Hi All,
>>
>>     We do have a problem with one of our MG8 switches. We've added a
>>     new BIMG8-10Gx4-v6-A blade, but after configuration the blade will
>>     not recover from CARD_STATE_INTERACTIVE.
>>
>>     S2: BIMG8-10Gx4-v6-A 4-port 10GbE IPv4/v6 Module (OACL) 
>>     CARD_STATE_INTERACTIVE    0   000c.db27.4560
>>
>>     Steps taken:
>>
>>     1. Reset module.
>>     2. Set type to the slot port.
>>     3. Turn on/off module.
>>
>>     Unfortunately we can't find any logs about the new blade, only the
>>     current state: **CARD_STATE_INTERACTIVE.
>>
>>     Kind regards,
>>
>>     Dominic
>>     **
>>
>>     *
>>
>>
>>     _______________________________________________
>>     foundry-nsp mailing list
>>     foundry-nsp at puck.nether.net <mailto:foundry-nsp at puck.nether.net>
>>     http://puck.nether.net/mailman/listinfo/foundry-nsp
> 
> 
> 
> 
> _______________________________________________
> foundry-nsp mailing list
> foundry-nsp at puck.nether.net
> http://puck.nether.net/mailman/listinfo/foundry-nsp