[f-nsp] Link Aggregation between Foundry and Cisco

[Big Wave Dave]

On Fri, Jan 7, 2011 at 4:27 PM, Joseph Hardeman <jwhardeman at gmail.com> wrote:
> Hi Everyone,
>
> I am having a bit of an issue, I have gotten a pair of Cisco 6509's with the
> SUP-720 engines.  I am trying to configure link aggregation between one of
> these to a BI4000 I have to test with before we put them into production and
> connect them to our BI8000's and fight this problem then.  I have been
> searching and looking at the docs I have.  The configuration I have on the
> Cisco's allow them to talk over the port channels between each other with no
> issues.
>
> I can setup the command "link-aggregation active" on port "ethe 1/5" with no
> issues it takes the command, but when I go to add a test VLAN on to that
> port I get the following error message:
>
> error - some ports are running LACP and can not be tagged ports.
>
> Here is the command I am running on the BI:
>
> test(config)#int e 1/5
> test(config-if-e1000-1/5)#link-aggregate configure key 10000
> test(config-if-e1000-1/5)#link-aggregate active
> test(config-if-e1000-1/5)#exit
> test(config)#vlan 14
> test(config-vlan-14)#tagged e 1/5
> error - some ports are running LACP and can not be tagged ports.
> test(config-vlan-14)#end
>
> Here is the output of sh int e 1/5"
> GigabitEthernet1/5 is up, line protocol is up
>  Hardware is GigabitEthernet, address is 00e0.52cc.3b04 (bia 00e0.52cc.3b04)
>  Configured speed 1Gbit, actual 1Gbit, configured duplex fdx, actual fdx
>  Member of L2 VLAN ID 1, port is untagged, port state is BLOCKING
>  STP configured to ON, priority is level0, flow control disabled
>  mirror disabled, monitor disabled
>  Not member of any active trunks
>  Not member of any configured trunks
>  No port name
>  MTU 1518 bytes, encapsulation ethernet
>  300 second input rate: 40104 bits/sec, 72 packets/sec, 0.00% utilization
>  300 second output rate: 0 bits/sec, 0 packets/sec, 0.00% utilization
>  899789 packets input, 62419802 bytes, 0 no buffer
>  Received 372 broadcasts, 899417 multicasts, 0 unicasts
>  0 input errors, 0 CRC, 0 frame, 0 ignored
>  0 runts, 0 giants, DMA received 899786 packets
>  0 packets output, 0 bytes, 0 underruns
>  Transmitted 0 broadcasts, 0 multicasts, 0 unicasts
>  0 output errors, 0 collisions, DMA transmitted 0 packets
>
>
> Output of sh link-aggregation:
> Long  timeout: 90, default: 90
> Short timeout: 3, default: 3
> Port  [Sys P] [Port P] [ Key ] [Act][Tio][Agg][Syn][Col][Dis][Def][Exp][Ope]
> 1/5        1        1       0   Yes   S   Agg  Syn  Col  Dis  Def  No   Blo
>
>
> So my question is what am I missing here?   From everything I found, all I
> have to do after setting 1 or more ports into a link-aggregation is to add
> the VLAN's as tagged to the ports with the same key.  But its not allowing
> me to add the tagged vlans.
>
> Any suggestions?
>
> Thanks
>
> Joe
> _______________________________________________


I've had similar problems before.
My bookmark takes me to:

http://www.techsneeze.com/create-vlan-trunk-between-cisco-ios-and-foundry-bigiron

Dave