[f-nsp] Enabling ipv6 on J-BxGMR4

Nick Gray ngray at cyberwurx.com
Thu Feb 16 11:50:24 EST 2012


Greetings and thanks for the information! Does anyone know where I
could get a B2R image? Also, will this new image remove configuration
options from B2P? If I deploy a B2R image on a production layer3
router deployment, would there be any issues?

Nick Gray
Cyber Wurx Operations



On Thu, Feb 16, 2012 at 5:16 AM, Jeroen Oldenhof <jeroen at cj2.nl> wrote:
> Hi Nick,
>
> you have B2Rxxx software running, which is the (R)outer image. IPv6 is only
> available with the B2Pxxx, the (P)rovider image.
>
> Best regards,
> Jeroen Oldenhof
>
>
>
> Op 16-2-2012 6:30, Nick Gray schreef:
>>
>> Greetings,
>>
>> I am having issues enabling ipv6 on a foundry bi8000 with J-BxGMR4
>> management modules.
>>
>> #show version
>>   SW: Version 08.0.01wT53 Copyright (c) 1996-2004 Foundry Networks, Inc.
>>       Compiled on Jun 18 2010 at 15:16:32 labeled as B2R08001w
>>       (3860139 bytes) from Primary B2R08001w.bin
>>   HW: BigIron 8000 Router, SYSIF version 21, Serial #: Non-exist
>> ==========================================================================
>> SL 1: J-BxGMR4 JetCore Management Module, SYSIF 2 (Mini GBIC), M4, ACTIVE
>>       Serial #:   xxxx
>>  4096 KB BRAM, JetCore ASIC IGC version 49, BIA version 89
>> 32768 KB PRAM and 2M-Bit*1 CAM for IGC  0, version 0449
>> 32768 KB PRAM and 2M-Bit*1 CAM for IGC  1, version 0449
>> ==========================================================================
>> SL 2: J-BxGMR4 JetCore Management Module, SYSIF 2 (Mini GBIC), M4, STANDBY
>>       Serial #:   xxxx
>>  4096 KB BRAM, JetCore ASIC IGC version 49, BIA version 89
>> 32768 KB PRAM and 2M-Bit*1 CAM for IGC  4, version 0449
>> 32768 KB PRAM and 2M-Bit*1 CAM for IGC  5, version 0449
>> ==========================================================================
>> SL 3: B2x10G Fiber Switch Module, SYSIF 2
>>       Serial #:   xxxx
>> 32768 KB BRAM, XPP version 88, XTM version 89
>>  4096 KB PRAM(4096K+0K) and 65536*1 CAM entries for DMA  8, version 0158
>>  4096 KB PRAM(4096K+0K) and 65536*1 CAM entries for DMA  9, version 0158
>> ==========================================================================
>>
>> When I try to run ipv6 unicast-routing the command is not accepted:
>> (config)#ipv6 unicast-routing
>> Invalid input ->  ipv6 unicast-routing
>> Type ? for a list
>>
>> This usually reflects an unsupported feature. Do you know where I
>> could get an update bin file that supports IPv6 in the event it is not
>> supported?
>>
>> Thanks for your help as usual!
>>
>> Nick
>> _______________________________________________
>> foundry-nsp mailing list
>> foundry-nsp at puck.nether.net
>> http://puck.nether.net/mailman/listinfo/foundry-nsp
>
>
> _______________________________________________
> foundry-nsp mailing list
> foundry-nsp at puck.nether.net
> http://puck.nether.net/mailman/listinfo/foundry-nsp




More information about the foundry-nsp mailing list