[f-nsp] RX-BI-4XG in reboot loop

[Rens Ariens - YISP]

Thanks for the replies so far. Some more information:

LP-5 Monitor>diag fap10m cpu-bus

FAP 0 CPU Bus Test Passed

FAP 1 CPU Bus Test FAILED
FAP 1 Data Bus Test Failed, expected aaaaaaaa actual aaaaaa8a

FAP 2 CPU Bus Test Passed

FAP 3 CPU Bus Test Passed


No errors on "diag fap10m 0" command. When running "diag fap10m 1" it 
starts to boot (strange?) and i'm seeing the same errors as earlier. The 
strange thing is when i test the sdram using "diag prestera sdram" i get 
a Passed on all sdram modules.


Rens



On 04/17/2013 12:09 AM, Josh Farrelly wrote:
> Looks to me like a good candidate for a hardware issue. If a power 
> off/power on and reload of firmwares don't resolve it's usually quite 
> broken.
>
> Regards,
>
> JF
>
>
> From: Rens Ariens - YISP <rens at yisp.nl <mailto:rens at yisp.nl>>
> Date: Wednesday, 17 April 2013 7:28 AM
> To: "foundry-nsp at puck.nether.net <mailto:foundry-nsp at puck.nether.net>" 
> <foundry-nsp at puck.nether.net <mailto:foundry-nsp at puck.nether.net>>
> Subject: [f-nsp] RX-BI-4XG in reboot loop
>
> Hello everyone,
>
> We have a RX-BI-4XG module in a reboot loop. Reloaded 
> boot/monitor/ironware images to it, but does not help. In rconsole on 
> boot i see the following not very promising information:
>
> Error: 0x08040001 - error in fap10m_i2c_write(): Cannot access chip 
> (0x2061b8e8,0xc0010000,0x400000f0,0x00000004,0x00000000,0x00000000)
>    Name: SAND_GEN_ERR: General error code (unspecified).
> Error: 0x08040001 - error in fap10m_eci_write(): Cannot access chip 
> (0x2061b8e8,0xc0010000,0x400000f0,0x00000004,0x00000000,0x00000000)
>    Name: SAND_GEN_ERR: General error code (unspecified).
> Error: 0x0844003c - General error in sand_mem_write() 
> (0x0000000b,0x400000f0,0x00000004,0x00000000,0x00000000,0x00000000)
>    Name: SAND_MEM_WRITE_006: Procedure sand_mem_write() reports:
> Failed to write to the chip
> Error: 0x180c003c - error in fap10m_mem_write() 
> (0x00000001,0x00000000,0x00000000,0x00000000,0x00000000,0x00000000)
>    Name: SAND_MEM_WRITE_006: Procedure sand_mem_write() reports:
> Failed to write to the chip
> i2c time out
> i2c write addr 000000e2 failed
> i2c time out
>
> Anyone seen this before? Fixable or hardware issue?
>
> Thanks in advance,
>
> Rens

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://puck.nether.net/pipermail/foundry-nsp/attachments/20130417/b51e4a9e/attachment.html>