[f-nsp] IPv6 support on FESX648-PREM

[ebradsha at gmail.com]

Hi Jeff,

Unfortunately the same result. Niels pointed out to me that BGP4+ isn't
supported by the FESX648-PREM, but I don't think his reply was CCed back to
the mailing list:

Is BGP4+ not supported on the FESX648-PREM?
>

Sadly, no...  See page 105 of the FastIron 7.2.02 Config Guide.


        -- Niels.




On Mon, Jun 30, 2014 at 6:42 PM, Jeff McAdams <jeffm at iglou.com> wrote:

> Just use "address-family ipv6"
>
> Leave off the unicast.  Probably a bug there, but is mostly harmless.
>
> Works great once you figure that little oddity out.
>
> On Mon, June 30, 2014 20:33, ebradsha at gmail.com wrote:
> > Hello,
> >
> >
> > We have a FESX648-PREM that I'd like to use to announce an IPv6 range. It
> >  was my understanding that the FESX648-PREM supported IPv6, but I can't
> > seem to enter the IPv6 section of my BGP config:
> >
> > SSH at FESX648 Router(config-bgp-router)# address-family ipv6 unicast
> > Invalid input -> address-family ipv6 unicast
> > Type ? for a list
> > SSH at FESX648 Router(config-bgp-router)#
> >
> >
> >
> > My router version info is as follows:
> >
> >
> > SSH at FESX648 Router(config-bgp-router)#show version
> > SW: Version 07.4.00eT3e3 Copyright (c) 1996-2012 Brocade Communications
> > Systems, Inc. All rights reserved.
> > Compiled on Dec 11 2013 at 19:00:43 labeled as SXR07400e
> > (4593059 bytes) Primary sxr07400e.bin
> > BootROM: Version 07.2.00T3e5 (FEv2)
> > HW: Stackable FESX648-PREM6 (PROM-TYPE FESX648-L3U-IPV6)
> >
> ==========================================================================
> >  Serial  #: XXXXXXXX
> > License: SX_V6_HW_ROUTER_IPv6_SOFT_PACKAGE   (LID: XXXXXXXXXX)
> > P-ASIC  0: type 0111, rev 00  subrev 01
> > P-ASIC  1: type 0111, rev 00  subrev 01
> > P-ASIC  2: type 0111, rev 00  subrev 01
> > P-ASIC  3: type 0111, rev 00  subrev 01
> >
> ==========================================================================
> >  300 MHz Power PC processor 8245 (version 0081/1014) 66 MHz bus
> > 512 KB boot flash memory
> > 8192 KB code flash memory
> > 256 MB DRAM
> > The system uptime is 23 days 13 hours 55 minutes 37 seconds
> > The system : started=cold start
> >
> >
> >
> > Is BGP4+ not supported on the FESX648-PREM?
> >
> >
> > - Elliot
> > _______________________________________________
> > foundry-nsp mailing list foundry-nsp at puck.nether.net
> > http://puck.nether.net/mailman/listinfo/foundry-nsp
>
>
> --
> Jeff
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://puck.nether.net/pipermail/foundry-nsp/attachments/20140630/7688c027/attachment.html>