[f-nsp] LACP with Foundry and Linux Machine

[Erich Hohermuth]

Hi Rupesh,

I guess you hit the hardware limits when you try to build the primary
port 4/2 on this "old" foundry device.

<snip>
Each trunk group must start with a primary port. The primary port is
always the lowest number in the port range. For example, trunk groups on
a Chassis device can have the following primary ports:
2-port trunk groups: 1, 3, 5, 7, 9, 11,13, 15, 17, 19, 21, 23
</snip>

Also you can choose the the trunk type switch (default) or server which
influence the hash algorithm for the balancing. See below:

http://www.foundrynet.com/services/documentation/sribcg/current/Trunking.html

Regards

Erich

Am 27.03.14 18:44, schrieb Rupesh Basnet:
> Hi All,
> 
> I have been trying LACP between Foundry and Linux machine since some
> days but not able to figure out the issue and resolve the issue. I
> didn't see much configurations thats needs to be done on foundry. I have
> configured my linux box on mode 0 and bonding seems to be up but still I
> am not able to pass traffic through it.
> 
> Serveriron Configurations:
> 
> interface ethernet 4/2
>  port-name **LACP-with-Linux***
>  no spanning-tree
>  link-aggregate active
> !
> interface ethernet 4/3
>  port-name **LACP-with-Linux***
>  no spanning-tree
>  link-aggregate active
> !
> 
> 
> SI#show version
>   SW: Version 09.3.00eTD4 Copyright (c) 1996-2003 Foundry Networks, Inc.
>       Compiled on Jun 28 2005 at 18:57:32 labeled as WXR09300e
>   HW: ServerIronGT E-2 Router, SYSIF version 21, Serial #: Non-exist
> ==========================================================================
> SL 1: B0GMR WSM2 Management Module, SYSIF 2, M6, ACTIVE
>       Serial #:   CH39040033
>     0 MB SHM, 2 Application Processors
> 16384 KB BRAM, SMC version 1, BM version 21
>   SW: (1)09.3.00eTF2 (2)09.3.00eTF2
> ==========================================================================
> SL 4: J-BxGC16 JetCore Gig Copper Module, SYSIF 2
>       Serial #:   CH33060779
>  4096 KB BRAM, JetCore ASIC IGC version 49, BIA version 8a
> 32768 KB PRAM and 2M-Bit*1 CAM for IGC 12, version 0449
> 32768 KB PRAM and 2M-Bit*1 CAM for IGC 13, version 0449
> 32768 KB PRAM and 2M-Bit*1 CAM for IGC 14, version 0449
> 32768 KB PRAM and 2M-Bit*1 CAM for IGC 15, version 0449
> 
> 
> SI#show link-aggregate
> System ID: 000c.db5d.b066
> Long  timeout: 90, default: 90
> Short timeout: 3, default: 3
> Port  [Sys P] [Port P] [ Key ]
> [Act][Tio][Agg][Syn][Col][Dis][Def][Exp][Ope]
> 4/2        1        1     483   Yes   S   Agg  Syn  Col  Dis  Def No   Ope
> 4/3        1        1     483   Yes   S   Agg  Syn  Col  Dis  Def No   Ope
> 
> 
> Status of linux machine:
> MII Status: up
> MII Polling Interval (ms): 30000
> Up Delay (ms): 0
> Down Delay (ms): 0
> 
> Slave Interface: eth0
> MII Status: up
> Speed: 1000 Mbps
> Duplex: full
> Link Failure Count: 0
> Permanent HW addr: 00:e0:ed:2b:a1:99
> Slave queue ID: 0
> 
> Slave Interface: eth1
> MII Status: up
> Speed: 1000 Mbps
> Duplex: full
> Link Failure Count: 0
> Permanent HW addr: 00:e0:ed:2b:a1:98
> Slave queue ID: 0
>