Fw: Re: Small Parts Needed

[R. L. Blaney]

Hi all,
I sent this direct to Stu, but some others may find it useful.
Dick, WB8MHE
wb8mhe at bright.net

>-----Original Message-----
>From: R. L. Blaney <wb8mhe at bright.net>
>To: stu_w6cux at JUNO.COM <stu_w6cux at JUNO.COM>
>Cc: Dick Blaney <wb8mhe at bright.net>
>Date: Thursday, December 03, 1998 11:11 PM
>Subject: Re: Re: Small Parts Needed
>
>
>>Hi Stu,
>>Yes, they have screws with Phillips or slotted heads, stainless, chrome,
>>steel, brass & plated.  Sizes are from 2-56 to 5/16-18.  Check on catalog
>>pages 2575 and 2576 for screws.  Countersunk washers are available in
>>standard and flanged.  Standard from #4 to 3/8", flanged in  #6, #8, &
#10.
>>They are on page 2654.  You have to buy by the 100, but they are not that
>>much, and good things to have on the shelf for the future.
>>Gud luck &73 de
>>Dick, WB8MHE
>>wb8mhe at bright.net
>>
>>-----Original Message-----
>>From: Stewart Lyon <stu_w6cux at JUNO.COM>
>>To: HEATH at LISTSERV.TEMPE.GOV <HEATH at LISTSERV.TEMPE.GOV>
>>Date: Thursday, December 03, 1998 10:45 PM
>>Subject: Re: Small Parts Needed
>>
>>
>>>Hi Doug & gang,
>>>Most of the parts you are looking for are readily available.
>>>
>>>The rubber feet are available from "R & R" ( who maintains an on-line
>>>catalog) and I have found them under the Dantona brand at Home Depot and
>>>at two local radio stores - they come in a blue blister pak, 4 to a pak.
>>>
>>>The bulbs are type 44 but should be replaced by type 47 which I found at
>>>RadioShack and the same radio stores plus All-electronics (which
>>>advertises in QST).
>>>
>>>The 2-pin mic connectors are now sold under the WPI brand and listed in
>>>both the Newark and Allied catalogs.  The microphone end is about $12 and
>>>the radio side about $8.  Someone also posted a source called "RF
>>>Connectors" or something like that a couple of months ago. I looked them
>>>up once and found their prices around $3-4.
>>>
>>>The posting by Dick,  WB8MHE about the 8-32 screws was good news to me
>>>since I too am looking for those screws.  Wonder if they have the
>>>phillips 6-32 screws that are on the front panel of these rigs??
>>>
>>>73, Stu - W6CUX
>>>Winnetka, CA
>>>
>>>On Thu, 3 Dec 1998 20:31:18 -0500 Doug Shields <dcb at ECQUAL.NET> writes:
>>>>Hello,
>>>>1.  8-32 Oval head screws that hold the lid closed on the SB-102, 300,
>>>>400 radios. These have a special undercut head.
>>>>2.  Rubber feet for the same radios.  That are an exact match for the
>>>>originals.
>>>>3.  Replacement bulbs for the meter and tuning dial backlights.
>>>>4.  2-Pin male microphone connectors for the SB-102, SB-401.
>>>
>>>>Thanks very much for your help.
>>>>Doug  W4DAS
>>>>
>>>
>>>--- --- --- --- --- --- --- --- --- --- --- --- --- --
>>>To subscribe: listserv at listserv.tempe.gov
>>>and in body: subscribe HEATH yourfirstname yourlastname
>>>To unsubscribe:  listserv at listserv.tempe.gov
>>>and in body: signoff HEATH
>>>Archives for HEATH: http://www.tempe.gov/archives
>>>--- --- --- --- --- --- --- --- --- --- --- --- --- --
>>>
>>
>

--- --- --- --- --- --- --- --- --- --- --- --- --- --
To subscribe: listserv at listserv.tempe.gov
and in body: subscribe HEATH yourfirstname yourlastname
To unsubscribe:  listserv at listserv.tempe.gov
and in body: signoff HEATH
Archives for HEATH: http://www.tempe.gov/archives
--- --- --- --- --- --- --- --- --- --- --- --- --- --