[j-nsp] RIP Question

[Mustafa taseli]

Thanks Harry
This exactly what I want... I want to distribute
lo0.1 with rip. I tried today and it worked fine

best regards


--- Harry Reynolds <harry at juniper.net> wrote:
> Not sure if this is what you are looking for, but
> here is a RIP VRF
> instance that redistributes a non-unit 0 lo0
> address. You can set the
> same address on unit 0 as unit 1, but this example
> uses a unique
> address. This was with 5.7, but also works with 5.6:
> 
> [edit]
> lab at London# run monitor traffic interface fe-0/0/1
> detail
> Listening on fe-0/0/1, capture size 96 bytes
> 
> 11:19:59.539849 Out IP (tos 0xc0, ttl 1, id 48855,
> len 52)
> 10.0.29.1.router > 224.0.0.9.router:
>         RIPv2, Response, length: 24, routes: 1
>           AFI: IPv4:         3.0.0.1/32, tag 0x0000,
> metric: 1,
> next-hop: self
> ^C
> 1 packets received by filter
> 0 packets dropped by kernel
> 
> [edit]
> lab at London# show interfaces lo0
> unit 0 {
>     family inet {
>         address 192.168.28.1/32;
>     }
> }
> unit 1 {
>     family inet {
>         address 3.0.0.1/32;
>     }
> }
> 
> [edit]
> lab at London# show policy-options
> policy-statement foo {
>     term 1 {
>         from {
>             protocol direct;
>             route-filter 3.0.0.1/32 exact;
>         }
>         then accept;
>     }
> }
> 
> [edit]
> lab at London# show routing-instances
> test {
>     instance-type vrf;
>     interface fe-0/0/1.0;
>     interface lo0.1;
>     route-distinguisher 10.0.1.1:1;
>     vrf-target target:65412:100;
>     protocols {
>         rip {
>             group test {
>                 export foo;
>                 neighbor fe-0/0/1.0;
>             }
>         }
>     }
> }
> 
> 
> HYHs
> 
> > -----Original Message-----
> > From: juniper-nsp-bounces at puck.nether.net
> > [mailto:juniper-nsp-bounces at puck.nether.net]On
> Behalf Of
> > Mustafa taseli
> > Sent: Monday, June 23, 2003 7:20 AM
> > To: juniper-nsp at puck.nether.net
> > Subject: [j-nsp] RIP Question
> >
> >
> > Hi All
> >
> > I want to run RIP in a routing-instance, I also
> > want to distribute my loopback addresses with rip
> > How can I do it ?? Any Idea ??
> >
> > Thanks in advance
> >
> > __________________________________
> > Do you Yahoo!?
> > SBC Yahoo! DSL - Now only $29.95 per month!
> > http://sbc.yahoo.com
> > _______________________________________________
> > juniper-nsp mailing list
> juniper-nsp at puck.nether.net
> >
> http://puck.nether.net/mailman/listinfo/juniper-nsp
> 
> _______________________________________________
> juniper-nsp mailing list juniper-nsp at puck.nether.net
> http://puck.nether.net/mailman/listinfo/juniper-nsp


__________________________________
Do you Yahoo!?
SBC Yahoo! DSL - Now only $29.95 per month!
http://sbc.yahoo.com