[j-nsp] "Invalid VCs" error message on ATM interface

[William Phang]

You may not able to upgrade the firmware since Juniper its self still cannot
rewrite the microcode at this time. The microcode for SAR chip is come from
Mindspeed. 

You may need to work out with JTAC and may be they can push to rewrite the
microcode to solve it. The error is very annoying when we run show
interface.

We just can hope that Juniper could solve it. 

 

-----Original Message-----
From: juniper-nsp-bounces at puck.nether.net
[mailto:juniper-nsp-bounces at puck.nether.net] On Behalf Of Patrick Liu
Sent: Wednesday, June 09, 2004 10:24 PM
To: juniper-nsp at puck.nether.net
Subject: RE: [j-nsp] "Invalid VCs" error message on ATM interface

Thanks for the info and we will try to stop those signaling VCs to see if it
helps or not. Do you have more information about this hardware bug? Will the
newer firmware on the ATM PIC fix this problem? It seems that we might have
to do the firmware upgrade.

Our SNMP tool reports interface errors on the ATM Interface. We don't seem
to experience performance impact. It's just annoying to see those errors
showing up on the report.

-----Original Message-----
From: William Phang [mailto:phangjk at hotpop.com] 
Sent: Wednesday, June 09, 2004 12:54 AM
To: Liu, Patrick [BL60:T830:EXCH]; juniper-nsp at puck.nether.net
Subject: RE: [j-nsp] "Invalid VCs" error message on ATM interface


Hi,

Why the "Invalid VCs" happen?. This is the explanation:

It goes up every time you receive a cell for a non-configured VC If
connected to an ATM switch, this routinely happens to reserved VCIs 5,16,18
etc being probed by the switch, so no harm here. Furthermore, until very
recently, JUNOS ATM PIC firmware was unable to register those cells
separately for interfaces on the same PIC.This means the counter could go up
on the wrong port

The source of the problem is in the chip. The microcode for the SAR chip to
increment this counter and one counter is maintained per chip, not per port.


The 'Invalid VCs" should never increase only in one case - when _both_ PIC
ports are connected to another router.

We have seen a lot of this problem and have working with JTAC. But it seems
very hard to solve since this is hardware bug.

Don't worry it will not impact to performance. I have test it.

Regards,

William Bong
CCIE#9332


-----Original Message-----
From: juniper-nsp-bounces at puck.nether.net
[mailto:juniper-nsp-bounces at puck.nether.net] On Behalf Of Patrick Liu
Sent: Wednesday, June 09, 2004 4:04 AM
To: juniper-nsp at puck.nether.net
Subject: [j-nsp] "Invalid VCs" error message on ATM interface

Hi,

We are seeing the "Invalid VCs" as input errors on an ATM interface of M10.
The error number is increasing randomly. We have tried to work with the
transport provider to identify the issue. They have indicated that they
shouldn't send cells with non-existent VC over to us. We have also tried to
turn on the monitoring on that interface. It doesn't give us too much
information. Does anyone out there have better ways / ideas to troubleshoot
this?

Thanks in advance. _______________________________________________
juniper-nsp mailing list juniper-nsp at puck.nether.net
http://puck.nether.net/mailman/listinfo/juniper-nsp


_______________________________________________
juniper-nsp mailing list juniper-nsp at puck.nether.net
http://puck.nether.net/mailman/listinfo/juniper-nsp