[j-nsp] M-20 to 3750 LACP config
Bostjan Fele
bostjan.fele at smart-com.si
Wed Apr 20 08:39:38 EDT 2005
Have tried something similar. After making LACP passive on M series I had
running ae. Did not investigate further into it...
Regards,
Bosjan
-----Original Message-----
From: juniper-nsp-bounces at puck.nether.net
[mailto:juniper-nsp-bounces at puck.nether.net] On Behalf Of Patrick Coppinger
Sent: 19. april 2005 14:03
To: juniper-nsp at puck.nether.net
Subject: [j-nsp] M-20 to 3750 LACP config
I've seen a few posts on this topic, and believe I have followed the
example closely, but both my port-channel interface (Down/Down) and ae0
interface (Up/Down) won't come up, even though the physical interfaces are
all Up/Up. Any tips would be appreciated.
chassis {
aggregated-devices {
ethernet {
device-count 1;
}
}
}
interfaces {
ge-0/2/0 {
gigether-options {
802.3ad ae0;
}
}
ge-0/3/0 {
gigether-options {
802.3ad ae0;
}
}
ae0 {
aggregated-ether-options {
no-flow-control;
link-speed 1g;
lacp {
active;
}
}
}
}
interface Port-channel1
no ip address
!
interface GigabitEthernet1/0/27
no ip address
channel-group 1 mode active
!
interface GigabitEthernet1/0/28
no ip address
channel-group 1 mode active
Switch:show po1
Port-channel1 is down, line protocol is down (notconnect)
Hardware is EtherChannel, address is 0000.0000.0000 (bia 0000.0000.0000)
MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Switch:show etherchannel detail
Channel-group listing:
-----------------------
Group: 1
----------
Group state = L2
Ports: 2 Maxports = 16
Port-channels: 1 Max Port-channels = 16
Protocol: LACP
Ports in the group:
-------------------
Port: Gi1/0/27
------------
Port state = Up Sngl-port-Bndl Mstr Not-in-Bndl
Channel group = 1 Mode = Active Gcchange = -
Port-channel = null GC = - Pseudo port-channel = Po1
Port index = 0 Load = 0x00 Protocol = LACP
Flags: S - Device is sending Slow LACPDUs F - Device is sending fast
LACPDUs.
A - Device is in active mode. P - Device is in passive mode.
Local information:
LACP port Admin Oper Port Port
Port Flags State Priority Key Key Number State
Gi1/0/27 SA indep 32768 0x1 0x1 0x1C 0x7D
Age of the port in the current state: 00d:00h:06m:33s
Port: Gi1/0/28
------------
Port state = Up Sngl-port-Bndl Mstr Not-in-Bndl
Channel group = 1 Mode = Active Gcchange = -
Port-channel = null GC = - Pseudo port-channel = Po1
Port index = 0 Load = 0x00 Protocol = LACP
Flags: S - Device is sending Slow LACPDUs F - Device is sending fast
LACPDUs.
A - Device is in active mode. P - Device is in passive mode.
Local information:
LACP port Admin Oper Port Port
Port Flags State Priority Key Key Number State
Gi1/0/28 SA indep 32768 0x1 0x1 0x1D 0x7D
Age of the port in the current state: 00d:00h:06m:58s
Port-channels in the group:
----------------------
Port-channel: Po1 (Primary Aggregator)
------------
Age of the Port-channel = 00d:00h:08m:07s
Logical slot/port = 10/1 Number of ports = 0
HotStandBy port = null
Port state = Port-channel Ag-Not-Inuse
Protocol = LACP
Patrick Coppinger
CCIE #14298
Senior Network Engineer
EarthLink, Inc
pcoppinger at corp.earthlink.net
(404) 748-7454 desk
(678) 592-7041 cell
_______________________________________________
juniper-nsp mailing list juniper-nsp at puck.nether.net
http://puck.nether.net/mailman/listinfo/juniper-nsp
More information about the juniper-nsp
mailing list