[j-nsp] BGP configuration problem

[vinay pit]

Help needed...

I already have created a routing instance for a
customer between R2 (Juniper ) and R1 (Cisco) , in the
routing instance i have defined the protocol bgp and
have mentioned the configuration which is as below.
*******************
R2 (Juniper config)
***************************************************************
description ***RI_Ce-1***;
instance-type vrf;
interface ge-1/0/0.1;
interface fe-1/2/3.1;
interface so-2/1/3.0;
route-distinguisher 456:1;
vrf-target target:456:1;
vrf-table-label;
routing-options {
    static {
        route 172.16.1.0/27 next-hop 10.0.0.2;
        route 172.16.2.0/27 next-hop 10.0.0.2;
        route 172.16.3.0/27 next-hop 10.0.0.2;
        route 172.16.4.0/27 next-hop 10.0.0.2;
    }
}
protocols {
    bgp {
        group ce-1 {
            local-address 10.1.0.2;
            authentication-key "$9$lbuMWx2gJDHm8XJD";
## SECRET-DATA
            export global_cust;
            peer-as 123;
            local-as 456;
            neighbor 10.1.0.1;
        }
        group test-1 {
            local-address 200.0.2.1;
            authentication-key "$9$Ddkqf9Cu1Ey.Pu1";
## SECRET-DATA
            export global_cust;
            peer-as 123;
            local-as 123;
            neighbor 200.0.2.2;
        }
    }
}
***************************************************************

The group ce-1 is for the BGP session between R2
(Juniper ) and R1 (Cisco)

Now i need to connect to a different cisco router R3
(cisco , route reflector). so i have created a group
called test-1 in the same routing instance. 

*****************************
the config of R3 is as below...
****************************************************************
router bgp 123
 bgp log-neighbor-changes
 neighbor 200.0.2.1 remote-as 123
 neighbor 200.0.2.1 password cisco
 !
 address-family ipv4
 no neighbor 200.0.2.1 activate
 no auto-summary
 no synchronization
 exit-address-family
 !
 address-family vpnv4
 neighbor 200.0.2.1 activate
 neighbor 200.0.2.1 route-reflector-client
 neighbor 200.0.2.1 send-community both
 exit-address-family
****************************************************************

Please help me out as the bgp sessions are not comming
up still in idle state......


Regards
Vinay 


> --- vinay pit <vinay_pit at yahoo.com> wrote:
> 
> > Dear All
> > 
> > I have very less experience in Juniper Routers. I
> > need
> > to configure a MPBGP session between a Juniper
> M40e
> > router and a cisco router. The cisco router acts a
> > RR
> > (Route Reflector) and the juniper router as a
> client
> > of it.
> > 
> > Please can any one tell me what all is the
> > configuration to be done on the Juniper router.
> > 
> > Regards
> > Vinay  
> > 
> > 
> > 		
> > __________________________________________ 
> > Yahoo! DSL – Something to write home about. 
> > Just $16.99/mo. or less. 
> > dsl.yahoo.com 
> > 
> > _______________________________________________
> > juniper-nsp mailing list
> juniper-nsp at puck.nether.net
> >
> http://puck.nether.net/mailman/listinfo/juniper-nsp
> > 
> 
> 
> 
> 	
> 		
> __________________________________ 
> Yahoo! for Good - Make a difference this year. 
> http://brand.yahoo.com/cybergivingweek2005/
> 



		
__________________________________________ 
Yahoo! DSL – Something to write home about. 
Just $16.99/mo. or less. 
dsl.yahoo.com