[j-nsp] M20 RE serious problem
Erdem Sener
erdems at gmail.com
Fri Oct 20 15:16:49 EDT 2006
Hi,
On single-user mode, did you try 'fsck' command and check the drives?
In some cases, I've seen it doing the trick.
HTH
On 10/20/06, Mesut Mutlu <kirdjali1978 at yahoo.com> wrote:
> Hi All,
>
> I need your help as soon as possible.
> One of he RE on our company M20 router is not becoming on. Its status after reboot is becoming off . We connected via console port to look at problems which seems to occur. But login and passwords defined before was not utilizable. Message as seem below is occured:
> RE1 (ttyd0)
> login: test
> Oct 20 16:27:09 RE1 login: _pam_init_handlers: could not open /etc/pam.conf
> Oct 20 16:27:09 RE1 login: pam_start: failed to initialize handlers
> Oct 20 16:27:09 RE1 login: LOGIN_PAM_START: Unable to start PAM session: Critical error - immediate abort
> Local Password:Oct 20 16:27:10 RE1 /kernel: veriexec: no signatures for device. file='/usr/sbin/eventd' dev=76578 inode=74404 uid=0 pid=2698
> Oct 20 16:27:10 RE1 /kernel: veriexec: no signatures for device. file='/usr/sbin/pppoed' dev=76554 inode=79988 uid=0 pid=2699
> Oct 20 16:27:10 RE1 /kernel: veriexec: no signatures for device. file='/usr/sbin/eccd' dev=76554 inode=76376 uid=0 pid=2700
> Oct 20 16:27:10 RE1 /kernel: veriexec: no signatures for device. file='/usr/sbin/irsd' dev=76554 inode=77684 uid=0 pid=2701
> Oct 20 16:27:10 RE1 /kernel: veriexec: no signatures for device. file='/usr/sbin/dfwd' dev=76554 inode=75892 uid=0 pid=2702
> Oct 20 16:27:10 RE1 /kernel: veriexec: no signatures for device. file='/usr/sbin/ksyncd' dev=76554 inode=78674 uid=0 pid=2703
> Oct 20 16:27:10 RE1 /kernel: veriexec: no signatures for device. file='/usr/sbin/smartd' dev=76554 inode=81200 uid=0 pid=2704
> Oct 20 16:27:10 RE1 /kernel: veriexec: no signatures for device. file='/usr/sbin/kmd' dev=76586 inode=67908 uid=0 pid=2705
> Oct 20 16:27:10 RE1 /kernel: veriexec: no signatures for device. file='/usr/sbin/pfed' dev=76554 inode=79630 uid=0 pid=2706
> Oct 20 16:27:10 RE1 /kernel: veriexec: no signatures for device. file='/usr/sbin/tnp.sntpc' dev=76554 inode=82164 uid=0 pid=2707
> Oct 20 16:27:10 RE1 /kernel: veriexec: no signatures for device. file='/usr/sbin/tnp.sntpd' dev=76554 inode=82290 uid=0 pid=2708
> Oct 20 16:27:10 RE1 /kernel: veriexec: no signatures for device. file='/usr/sbin/snmpd' dev=76554 i
> Login incorrect
> login: Oct 20 16:27:10 RE1 /kernel: veriexec: no signatures for device. file='/usr/sbin/snmpd' dev=76554 inode=81436 uid=0 pid=2710
> Oct 20 16:27:10 RE1 /kernel: veriexec: no signatures for device. file='/usr/sbin/mgd' dev=76578 inode=75000 uid=0 pid=2711
> Oct 20 16:27:10 RE1 /kernel: veriexec: no signatures for device. file='/usr/sbin/craftd' dev=76554 inode=75248 uid=0 pid=2712
> Oct 20 16:27:10 RE1 /kernel: veriexec: no signatures for device. file='/usr/sbin/alarmd' dev=76554 inode=73932 uid=0 pid=2713
> Oct 20 16:27:10 RE1 /kernel: veriexec: no signatures for device. file='/usr/sbin/chassisd' dev=76554 inode=74648 uid=0 pid=2714
> Oct 20 16:27:10 RE1 /kernel: veriexec: no signatures for device. file='/sbin/dcd' dev=76554 inode=86220 uid=0 pid=2715
> Oct 20 16:27:10 RE1 /kernel: veriexec: no signatures for device. file='/usr/sbin/tnetd' dev=76554 inode=82044 uid=0 pid=2716
> Oct 20 16:27:15 RE1 /kernel: veriexec: no signatures for device. file='/usr/sbin/eventd' dev=76578 inode=74404 uid=0 pid=2770
> Oct 20 16:27:15 RE1 /kernel: veriexec: no signatures for device. file='/usr/sbin/eccd' dev=76554 inode=76376 uid=0 pid=2771
> Oct 20 16:27:15 RE1 /kernel: veriexec: no signatures for device. file='/usr/sbin/pppoed' dev=76554 inode=79988 uid=0 pid=2772
> Oct 20 16:27:15 RE1 /kernel: veriexec: no signatures for device. file='/usr/sbin/irsd' dev=76554 inode=77684 uid=0 pid=2773
> Oct 20 16:27:15 RE1 /kernel: veriexec: no signatures for device. file='/usr/sbin/dfwd' dev=76554 in
> login: teOct 20 16:27:15 RE1 /kernel: veriexec: no signatures for device. file='/usr/sbin/dfwd' dev=76554 inode=75892 uid=0 pid=2774
> Oct 20 16:27:15 RE1 /kernel: veriexec: no signatures for device. file='/usr/sbin/ksyncd' dev=76554 inode=78674 uid=0 pid=2775
> Oct 20 16:27:15 RE1 /kernel: veriexec: no signatures for device. file='/usr/sbin/mgd' dev=76578 inode=75000 uid=0 pid=2777
> Oct 20 16:27:15 RE1 /kernel: veriexec: no signatures for device. file='/usr/sbin/snmpd' dev=76554 inode=81436 uid=0 pid=2778
> Oct 20 16:27:15 RE1 /kernel: veriexec: no signatures for device. file='/usr/sbin/tnp.sntpd' dev=76554 inode=82290 uid=0 pid=2779
> Oct 20 16:27:15 RE1 /kernel: veriexec: no signatures for device. file='/usr/sbin/tnetd' dev=76554 inode=82044 uid=0 pid=2780
> Oct 20 16:27:15 RE1 /kernel: veriexec: no signatures for device. file='/sbin/dcd' dev=76554 inode=86220 uid=0 pid=2781
> Oct 20 16:27:15 RE1 /kernel: veriexec: no signatures for device. file='/usr/sbin/chassisd' dev=76554 inode=74648 uid=0 pid=2782
> Oct 20 16:27:15 RE1 /kernel: veriexec: no signatures for device. file='/usr/sbin/alarmd' dev=76554 inode=73932 uid=0 pid=2783
> Oct 20 16:27:15 RE1 /kernel: veriexec: no signatures for device. file='/usr/sbin/craftd' dev=76554 inode=75248 uid=0 pid=2784
> Oct 20 16:27:15 RE1 /kernel: veriexec: no signatures for device. file='/usr/sbin/tnp.sntpc' dev=76554 inode=82164 uid=0 pid=2785
> Oct 20 16:27:15 RE1 /kernel: veriexec: no signatures for device. file='/usr/sbin/pfed' dev=76554 inst
> Oct 20 16:27:21 RE1 login: _pam_init_handlers: could not open /etc/pam.conf
> Oct 20 16:27:21 RE1 login: pam_start: failed to initialize handlers
> Oct 20 16:27:21 RE1 login: LOGIN_PAM_START: Unable to start PAM session: Critical error - immediate abort
> Local Password:
> Oct 20 16:27:20 RE1 syslogd: dropping message (console): Resource temporarily unavailable
>
> Then tried procedure for password recovery as it is defined on http://juniper.cluepon.net/index.php/Password_recovery site but unfortunately it also did not work.
>
> I am attaching the logs occured durung password recovery and after restarting RE .
> Could you please send me relevant information about this problem and (if there are) possible solutions.
>
> Thanks a lot. Have a nice day.
>
>
> RE1 (ttyd0)
> login:
> RE1 (ttyd0)
> login:
> RE1 (ttyd0)
> login: test
> Oct 20 16:17:59 RE1 login: _pam_init_handlers: could not open /etc/pam.conf
> Oct 20 16:17:59 RE1 login: pam_start: failed to initialize handlers
> Oct 20 16:17:59 RE1 login: LOGIN_PAM_START: Unable to start PAM session: Critical error - immediate abort
> Local Password:
> --- JUNOS 7.5R3.1 built 2006-07-14 17:14:21 UTC
> Oct 20 16:18:17 RE1 /kernel: veriexec: no signatures for device. file='/usr/sbin/cli' dev=76578 inode=74288 uid=2003 pid=2825
> Oct 20 16:18:17 RE1 login: LOGIN_SHELL: Failed to execute shell /usr/sbin/cli for user test: Authentication error
> login: /usr/sbin/cli: Authentication error
> Test_M20_RR
> RE1 (ttyd0)
> login:
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
> Trying to boot from PCMCIA Flash Card ...
>
> Trying to boot from Compact Flash ...
>
> >> FreeBSD/i386 BOOT
> Default: 0:ad(0,a)/boot/loader
> boot:
>
>
>
>
>
>
>
> Console: serial port
> BIOS drive C: is disk0
> BIOS drive D: is disk1
> BIOS 638kB/2096128kB available memory
>
> FreeBSD/i386 bootstrap loader, Revision 0.8
> (builder at uraeus.juniper.net, Fri Jul 14 16:43:27 GMT 2006)
> Loading /boot/defaults/loader.conf
> /kernel text=0x4530d5 data=0x377dc+0x57522 syms=[0x4+0x52830+0x4+0x60c24]
>
> Hit [Enter] to boot immediately, or space bar for command prompt.
>
> Type '?' for a list of commands, 'help' for more detailed help.
> ok boot -s
> Copyright (c) 1996-2001, Juniper Networks, Inc.
> All rights reserved.
> Copyright (c) 1992-2004 The FreeBSD Project.
> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
> The Regents of the University of California. All rights reserved.
> JUNOS 7.5R3.1 #0: 2006-07-14 17:14:21 UTC
> builder at uraeus.juniper.net:/build/uraeus-c/7.5R3.1/obj-i386/sys/compile/JUNIPER
> Timecounter "i8254" frequency 1193182 Hz
> Timecounter "TSC" frequency 601368767 Hz
> CPU: Intel Pentium III (601.37-MHz 686-class CPU)
> Origin = "GenuineIntel" Id = 0x68a Stepping = 10
> Features=0x387f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,PN,MMX,FXSR,SSE>
> real memory = 2147483648 (2097152K bytes)
> sio0: gdb debugging port
> avail memory = 2087034880 (2038120K bytes)
> Preloaded elf kernel "kernel" at 0xc0698000.
> DEVFS: ready for devices
> Pentium Pro MTRR support enabled
> md0: Malloc disk
> Using $PIR table, 13 entries at 0xc00fdef0
> DRAM Data Integrity Mode: ECC Mode with h/w scrubbing
> npx0: <math processor> on motherboard
> npx0: INT 16 interface
> pcib0: <ServerWorks NB6635 3.0LE host to PCI bridge> on motherboard
> pci0: <PCI bus> on pcib0
> pcic0: <TI PCI-1410 PCI-CardBus Bridge> irq 15 at device 1.0 on pci0
> pcic0: PCI Memory allocated: 0xf8000000
> pcic0: TI12XX PCI Config Reg: [pwr save][pci only]
> pccard0: <PC Card bus -- legacy version> on pcic0
> fxp0: <Intel Embedded 10/100 Ethernet> port 0x1000-0x103f mem 0xfbc00000-0xfbc1ffff,0xfbc20000-0xfbc20fff irq 9 at device 3.0 on pci0
> fxp1: <Intel Embedded 10/100 Ethernet> port 0x1040-0x107f mem 0xfbc40000-0xfbc5ffff,0xfbc21000-0xfbc21fff irq 11 at device 4.0 on pci0
> isab0: <ServerWorks IB6566 PCI to ISA bridge> at device 15.0 on pci0
> isa0: <ISA bus> on isab0
> atapci0: <ServerWorks ROSB4 ATA33 controller> port 0x1080-0x108f at device 15.1 on pci0
> ata0: at 0x1f0 irq 14 on atapci0
> smb0: <Intel 82371AB Compatible SMB controller> mem 0xfbc22000-0xfbc22fff irq 11 at device 15.0 on pci0
> pcib1: <ServerWorks NB6635 3.0LE host to PCI bridge> on motherboard
> pci1: <PCI bus> on pcib1
> orm0: <Option ROMs> at iomem 0xc0800-0xc17ff,0xdc000-0xdffff on isa0
> ata2 at port 0x170-0x177,0x376 irq 15 on isa0
> atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
> sc0: <System console> at flags 0x100 on isa0
> sc0: EGA <16 virtual consoles, flags=0x100>
> sio0 at port 0x3f8-0x3ff irq 4 flags 0x90 on isa0
> sio0: type 16550A, console
> sio1 at port 0x3e8-0x3ef irq 5 on isa0
> sio1: type 16550A
> sio2 at port 0x2f8-0x2ff irq 3 on isa0
> sio2: type 16550A
> sio3 at port 0x2e8-0x2ef irq 7 on isa0
> sio3: type 16550A
> fxp0: Ethernet address 00:80:42:13:5e:f9
> fxp1: Ethernet address 02:01:00:00:00:05
> DEVFS: ready to run
> ad0: 245MB <SanDisk SDCFB-256> [980/16/32] at ata0-master PIO4
> ad1: DMA limited to UDMA33
> ad1: 28615MB <FUJITSU MHT2030AT> [58140/16/63] at ata0-slave UDMA33
> Mounting root from ufs:/dev/ad0s1a
> WARNING: / was not properly dismounted
> if_pfe_open: listener socket opened, listening...
> Mounted jbase package on /dev/vn0...
> System watchdog timer disabled
> Enter full pathname of shell or 'recovery' for root password recovery or RETURN for /bin/sh:
> NOTE: to go to multi-user operation, exit the single-user shell (with ^D)
> # /usr/libexec/ui/recovery-mode
> Performing filesystem consistency checks ...
> /dev/ad0s1a: 1210 files, 46081 used, 172680 free (88 frags, 21574 blocks, 0.0% fragmentation)
> /dev/ad0s1e: 5 files, 13 used, 24272 free (8 frags, 3033 blocks, 0.0% fragmentation)
> Performing mount of main filesystems ...
> Performing filesystem consistency of secondary filesystems ...
> /dev/ad1s1f: 271 files, 227649 used, 25897258 free (706 frags, 3237069 blocks, 0.0% fragmentation)
> Performing mount of secondary filesystems ...
> Mounted jkernel package on /dev/vn1...
> Mounted jpfe package on /dev/vn2...
> Mounted jroute package on /dev/vn3...
> Mounted jcrypto package on /dev/vn4...
> machdep.bootsuccess: 1 -> 1
> Performing initialization of management services ...
> mgd: error: could not open database: /var/run/db/schema.db: No such file or directory
> mgd: error: Database open failed for file '/var/run/db/schema.db': No such file or directory
> mgd: error: could not open database schema: /var/run/db/schema.db
> mgd: error: could not open database schema
> mgd: error: database schema is out of date, rebuilding it
> mgd: error: could not open database: /var/run/db/juniper.data: No such file or directory
> mgd: error: Database open failed for file '/var/run/db/juniper.data': No such file or directory
> mgd: error: Cannot read configuration: Could not open configuration database
>
> Performing checkout of management services ...
> NOTE: Once in the CLI, you will need to enter configuration mode using
> NOTE: the 'configure' command to make any required changes. For example,
> NOTE: to reset the root password, type:
> NOTE: configure
> NOTE: set system root-authentication plain-text-password
> NOTE: (enter the new password when asked)
> NOTE: commit
> NOTE: exit
> NOTE: exit
> NOTE: When you exit the CLI, you will be asked if you want to reboot
> NOTE: the system
> Starting CLI ...
> root>
> root>
>
>
> Commands listed on http://juniper.cluepon.net/index.php/Password_recovery was executed. Nothing changed. After reboot everything was same as before as can be seen below.
>
>
>
>
>
> Trying to boot from PCMCIA Flash Card ...
>
> Trying to boot from Compact Flash ...
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
> onsole: serial port
> BIOS drive C: is disk0
> BIOS drive D: is disk1
> BIOS 638kB/2096128kB available memory
> FreeBSD/i386 bootstrap loader, Revision 0.8
> (builder at uraeus.juniper.net, Fri Jul 14 16:43:27 GMT 2006)
> Loading /boot/defaults/loader.conf
> /kernel text=0x4530d5 data=0x377dc+0x57522 syms=[0x4+0x52830+0x4+0x60c24]
>
> Hit [Enter] to boot immediately, or space bar for command prompt.
> Booting [kernel]...
> Copyright (c) 1996-2001, Juniper Networks, Inc.
> All rights reserved.
> Copyright (c) 1992-2004 The FreeBSD Project.
> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
> The Regents of the University of California. All rights reserved.
> JUNOS 7.5R3.1 #0: 2006-07-14 17:14:21 UTC
> builder at uraeus.juniper.net:/build/uraeus-c/7.5R3.1/obj-i386/sys/compile/JUNIPER
> Timecounter "i8254" frequency 1193182 Hz
> Timecounter "TSC" frequency 601368740 Hz
> CPU: Intel Pentium III (601.37-MHz 686-class CPU)
> Origin = "GenuineIntel" Id = 0x68a Stepping = 10
> Features=0x387f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,PN,MMX,FXSR,SSE>
> real memory = 2147483648 (2097152K bytes)
> sio0: gdb debugging port
> avail memory = 2087034880 (2038120K bytes)
> Preloaded elf kernel "kernel" at 0xc0698000.
> DEVFS: ready for devices
> Pentium Pro MTRR support enabled
> md0: Malloc disk
> Using $PIR table, 13 entries at 0xc00fdef0
> DRAM Data Integrity Mode: ECC Mode with h/w scrubbing
> npx0: <math processor> on motherboard
> npx0: INT 16 interface
> pcib0: <ServerWorks NB6635 3.0LE host to PCI bridge> on motherboard
> pci0: <PCI bus> on pcib0
> pcic0: <TI PCI-1410 PCI-CardBus Bridge> irq 15 at device 1.0 on pci0
> pcic0: PCI Memory allocated: 0xf8000000
> pcic0: TI12XX PCI Config Reg: [pwr save][pci only]
> pccard0: <PC Card bus -- legacy version> on pcic0
> fxp0: <Intel Embedded 10/100 Ethernet> port 0x1000-0x103f mem 0xfbc00000-0xfbc1ffff,0xfbc20000-0xfbc20fff irq 9 at device 3.0 on pci0
> fxp1: <Intel Embedded 10/100 Ethernet> port 0x1040-0x107f mem 0xfbc40000-0xfbc5ffff,0xfbc21000-0xfbc21fff irq 11 at device 4.0 on pci0
> isab0: <ServerWorks IB6566 PCI to ISA bridge> at device 15.0 on pci0
> isa0: <ISA bus> on isab0
> atapci0: <ServerWorks ROSB4 ATA33 controller> port 0x1080-0x108f at device 15.1 on pci0
> ata0: at 0x1f0 irq 14 on atapci0
> smb0: <Intel 82371AB Compatible SMB controller> mem 0xfbc22000-0xfbc22fff irq 11 at device 15.0 on pci0
> pcib1: <ServerWorks NB6635 3.0LE host to PCI bridge> on motherboard
> pci1: <PCI bus> on pcib1
> orm0: <Option ROMs> at iomem 0xc0800-0xc17ff,0xdc000-0xdffff on isa0
> ata2 at port 0x170-0x177,0x376 irq 15 on isa0
> atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
> sc0: <System console> at flags 0x100 on isa0
> sc0: EGA <16 virtual consoles, flags=0x100>
> sio0 at port 0x3f8-0x3ff irq 4 flags 0x90 on isa0
> sio0: type 16550A, console
> sio1 at port 0x3e8-0x3ef irq 5 on isa0
> sio1: type 16550A
> sio2 at port 0x2f8-0x2ff irq 3 on isa0
> sio2: type 16550A
> sio3 at port 0x2e8-0x2ef irq 7 on isa0
> sio3: type 16550A
> fxp0: Ethernet address 00:80:42:13:5e:f9
> fxp1: Ethernet address 02:01:00:00:00:05
> DEVFS: ready to run
> ad0: 245MB <SanDisk SDCFB-256> [980/16/32] at ata0-master PIO4
> ad1: DMA limited to UDMA33
> ad1: 28615MB <FUJITSU MHT2030AT> [58140/16/63] at ata0-slave UDMA33
> Mounting root from ufs:/dev/ad0s1a
> WARNING: / was not properly dismounted
> if_pfe_open: listener socket opened, listening...
> Mounted jbase package on /dev/vn0...
> Verified manifest signed by PackageProduction_7_5_0
> Verified jboot signed by PackageProduction_7_5_0
> Mounted jkernel package on /dev/vn1...
> Mounted jpfe package on /dev/vn2...
> Mounted jdocs package on /dev/vn3...
> Mounted jroute package on /dev/vn4...
> Mounted jcrypto package on /dev/vn5...
> Mounted jpfe-common package on /dev/vn6...
> swapon: adding /dev/ad1s1b as swap device
> Automatic reboot in progress...
> /dev/ad0s1a: 1210 files, 46081 used, 172680 free /dev/ad0s1e: 5 files, 13 used, 24272 free (88 frags, 21574 blocks, 0.0% fragmentation)
> (8 frags, 3033 blocks, 0.0% fragmentation)
> (88 frags, 21574 blocks, 0.0% fragmentation)
>
> /dev/ad1s1f: 264 files, 232401 used, 25892506 free (722 frags, 3236473 blocks, 0.0% fragmentation)
> tunefs: soft updates set
> veriexec: no signatures for device. file='/usr/sbin/rpdc' dev=76578 inode=75892 uid=0 pid=2513
> Creating initialv configuration..e.riexec: no signatures for device. file='/usr/sbin/mgd' dev=76578 inode=75000 uid=0 pid=2517
> watchdog: failed to exec command: /usr/sbin/mgd
> Warning: Commit failed, activating partial configuration.
> Warning: Edit the router configuration to fix these errors.
> cp: /var/run/db/juniper.db: No such file or directory
> Setting initial options: debugger_on_panic=NO debugger_on_break=NO.
> Setup PC-CARD: memory pccardd.
> Doing initial network setup:.
> vInitial interfacee configuration:r
> iexec: no signatures for device. file='/usr/sbin/irsd' dev=76554 inode=77684 uid=0 pid=2530
> /packages/mnt/jbvase/etc/rc: /usre/sbin/irsd: errorr 80
> iexec: no signatures for device. file='/usr/sbin/chassisd' dev=76554 inode=74648 uid=0 pid=2531
> /packages/mnt/jbvase/etc/rc: chasesisd: error 80
> riexec: no signatures for device. file='/sbin/dcd' dev=76554 inode=86220 uid=0 pid=2532
> /packages/mnt/jbase/etc/rc: dcd: error 80
> additional daemons:.
> checking for core dump...
> savecore: Reboot reason(s): 0x4: reset-button reset
> Oct 20 16:27:02 RE1 savecore: Reboot reason(s): 0x4: reset-button reset
> Additional routing options: ipsec kld.
> Doing additional network setup:.
> Starting final network daemons:.
> setting ldconfig path: /usr/lib /opt/lib
> starting standard daemons: cron.
> Initial rc.i386 initialization: microcode kld.
> Local package initialization:.
> kern.securelevel: -1 -> 1
> starting local daemons:.
> Fri Oct 20 16:27:04 EEST 2006
> O O Test_M20_RR
> RE1 (ttyd0)
> login:
> RE1 (ttyd0)
> login:
> RE1 (ttyd0)
> login: test
> Oct 20 16:27:09 RE1 login: _pam_init_handlers: could not open /etc/pam.conf
> Oct 20 16:27:09 RE1 login: pam_start: failed to initialize handlers
> Oct 20 16:27:09 RE1 login: LOGIN_PAM_START: Unable to start PAM session: Critical error - immediate abort
> Local Password:Oct 20 16:27:10 RE1 /kernel: veriexec: no signatures for device. file='/usr/sbin/eventd' dev=76578 inode=74404 uid=0 pid=2698
> Oct 20 16:27:10 RE1 /kernel: veriexec: no signatures for device. file='/usr/sbin/pppoed' dev=76554 inode=79988 uid=0 pid=2699
> Oct 20 16:27:10 RE1 /kernel: veriexec: no signatures for device. file='/usr/sbin/eccd' dev=76554 inode=76376 uid=0 pid=2700
> Oct 20 16:27:10 RE1 /kernel: veriexec: no signatures for device. file='/usr/sbin/irsd' dev=76554 inode=77684 uid=0 pid=2701
> Oct 20 16:27:10 RE1 /kernel: veriexec: no signatures for device. file='/usr/sbin/dfwd' dev=76554 inode=75892 uid=0 pid=2702
> Oct 20 16:27:10 RE1 /kernel: veriexec: no signatures for device. file='/usr/sbin/ksyncd' dev=76554 inode=78674 uid=0 pid=2703
> Oct 20 16:27:10 RE1 /kernel: veriexec: no signatures for device. file='/usr/sbin/smartd' dev=76554 inode=81200 uid=0 pid=2704
> Oct 20 16:27:10 RE1 /kernel: veriexec: no signatures for device. file='/usr/sbin/kmd' dev=76586 inode=67908 uid=0 pid=2705
> Oct 20 16:27:10 RE1 /kernel: veriexec: no signatures for device. file='/usr/sbin/pfed' dev=76554 inode=79630 uid=0 pid=2706
> Oct 20 16:27:10 RE1 /kernel: veriexec: no signatures for device. file='/usr/sbin/tnp.sntpc' dev=76554 inode=82164 uid=0 pid=2707
> Oct 20 16:27:10 RE1 /kernel: veriexec: no signatures for device. file='/usr/sbin/tnp.sntpd' dev=76554 inode=82290 uid=0 pid=2708
> Oct 20 16:27:10 RE1 /kernel: veriexec: no signatures for device. file='/usr/sbin/snmpd' dev=76554 i
> Login incorrect
> login: Oct 20 16:27:10 RE1 /kernel: veriexec: no signatures for device. file='/usr/sbin/snmpd' dev=76554 inode=81436 uid=0 pid=2710
> Oct 20 16:27:10 RE1 /kernel: veriexec: no signatures for device. file='/usr/sbin/mgd' dev=76578 inode=75000 uid=0 pid=2711
> Oct 20 16:27:10 RE1 /kernel: veriexec: no signatures for device. file='/usr/sbin/craftd' dev=76554 inode=75248 uid=0 pid=2712
> Oct 20 16:27:10 RE1 /kernel: veriexec: no signatures for device. file='/usr/sbin/alarmd' dev=76554 inode=73932 uid=0 pid=2713
> Oct 20 16:27:10 RE1 /kernel: veriexec: no signatures for device. file='/usr/sbin/chassisd' dev=76554 inode=74648 uid=0 pid=2714
> Oct 20 16:27:10 RE1 /kernel: veriexec: no signatures for device. file='/sbin/dcd' dev=76554 inode=86220 uid=0 pid=2715
> Oct 20 16:27:10 RE1 /kernel: veriexec: no signatures for device. file='/usr/sbin/tnetd' dev=76554 inode=82044 uid=0 pid=2716
> Oct 20 16:27:15 RE1 /kernel: veriexec: no signatures for device. file='/usr/sbin/eventd' dev=76578 inode=74404 uid=0 pid=2770
> Oct 20 16:27:15 RE1 /kernel: veriexec: no signatures for device. file='/usr/sbin/eccd' dev=76554 inode=76376 uid=0 pid=2771
> Oct 20 16:27:15 RE1 /kernel: veriexec: no signatures for device. file='/usr/sbin/pppoed' dev=76554 inode=79988 uid=0 pid=2772
> Oct 20 16:27:15 RE1 /kernel: veriexec: no signatures for device. file='/usr/sbin/irsd' dev=76554 inode=77684 uid=0 pid=2773
> Oct 20 16:27:15 RE1 /kernel: veriexec: no signatures for device. file='/usr/sbin/dfwd' dev=76554 in
> login: teOct 20 16:27:15 RE1 /kernel: veriexec: no signatures for device. file='/usr/sbin/dfwd' dev=76554 inode=75892 uid=0 pid=2774
> Oct 20 16:27:15 RE1 /kernel: veriexec: no signatures for device. file='/usr/sbin/ksyncd' dev=76554 inode=78674 uid=0 pid=2775
> Oct 20 16:27:15 RE1 /kernel: veriexec: no signatures for device. file='/usr/sbin/mgd' dev=76578 inode=75000 uid=0 pid=2777
> Oct 20 16:27:15 RE1 /kernel: veriexec: no signatures for device. file='/usr/sbin/snmpd' dev=76554 inode=81436 uid=0 pid=2778
> Oct 20 16:27:15 RE1 /kernel: veriexec: no signatures for device. file='/usr/sbin/tnp.sntpd' dev=76554 inode=82290 uid=0 pid=2779
> Oct 20 16:27:15 RE1 /kernel: veriexec: no signatures for device. file='/usr/sbin/tnetd' dev=76554 inode=82044 uid=0 pid=2780
> Oct 20 16:27:15 RE1 /kernel: veriexec: no signatures for device. file='/sbin/dcd' dev=76554 inode=86220 uid=0 pid=2781
> Oct 20 16:27:15 RE1 /kernel: veriexec: no signatures for device. file='/usr/sbin/chassisd' dev=76554 inode=74648 uid=0 pid=2782
> Oct 20 16:27:15 RE1 /kernel: veriexec: no signatures for device. file='/usr/sbin/alarmd' dev=76554 inode=73932 uid=0 pid=2783
> Oct 20 16:27:15 RE1 /kernel: veriexec: no signatures for device. file='/usr/sbin/craftd' dev=76554 inode=75248 uid=0 pid=2784
> Oct 20 16:27:15 RE1 /kernel: veriexec: no signatures for device. file='/usr/sbin/tnp.sntpc' dev=76554 inode=82164 uid=0 pid=2785
> Oct 20 16:27:15 RE1 /kernel: veriexec: no signatures for device. file='/usr/sbin/pfed' dev=76554 inst
> Oct 20 16:27:21 RE1 login: _pam_init_handlers: could not open /etc/pam.conf
> Oct 20 16:27:21 RE1 login: pam_start: failed to initialize handlers
> Oct 20 16:27:21 RE1 login: LOGIN_PAM_START: Unable to start PAM session: Critical error - immediate abort
> Local Password:
> Oct 20 16:27:20 RE1 syslogd: dropping message (console): Resource temporarily unavailable
> Oct 20 16:27:20 RE1 /kernel: veriexec: no signatures for device. file='/usr/sbin/eventd' dev=76578 inode=74404 uid=0 pid=2789
> Oct 20 16:27:20 RE1 syslogd: dropping message (console): Resource temporarily unavailable
> Oct 20 16:27:20 RE1 /kernel: veriexec: no signatures for device. file='/usr/sbin/pppoed' dev=76554 inode=79988 uid=0 pid=2790
> Oct 20 16:27:20 RE1 syslogd: dropping message (console): Resource temporarily unavailable
> Oct 20 16:27:20 RE1 /kernel: veriexec: no signatures for device. file='/usr/sbin/eccd' dev=76554 inode=76376 uid=0 pid=2791
> Oct 20 16:27:20 RE1 init: event-processing is thrashing, not restarted
> Oct 20 16:27:20 RE1 /kernel: veriexec: no signatures for device. file='/usr/sbin/cli' dev=76578 inode=74288 uid=0 pid=2808
> Oct 20 16:27:20 RE1 init: ecc-error-logging is thrashing, not restarted
> Oct 20 16:27:20 RE1 /kernel: veriexec: no signatures for device. file='/usr/sbin/cli' dev=76578 inode=74288 uid=0 pid=2809
> Oct 20 16:27:20 RE1 init: pppoe is thrashing, not restarted
> Oct 20 16:27:20 RE1 /kernel: veriexec: no signatures for device. file='/usr/sbin/cli' dev=76578 inode=74288 uid=0 pid=2810
> Oct 20 16:27:20 RE1 /kernel: veriexec: no signatures for device. file='/usr/sbin/irsd' dev=76554 inode=77684 uid=0 pid=2792
> Oct 20 16:27:20 RE1 init: internal-routing-service is thrashing, not restarted
> Oct 20 16:27:20 RE1 /kernel: veriexec: no signatures for device. file='/usr/sbin/dfwd' dev=76554 inOct 20 16:27:20 RE1 init: firewall is thrashing, not restarted
> Oct 20 16:27:20 RE1 /kernel: veriexec: no signatures for device. file='/usr/sbin/cli' dev=76578 inode=74288 uid=0 pid=2811
> Oct 20 16:27:20 RE1 init: kernel-replication is thrashing, not restarted
> Oct 20 16:27:20 RE1 /kernel: veriexec: no signatures for device. file='/usr/sbin/cli' dev=76578 inode=74288 uid=0 pid=2812
> Oct 20 16:27:20 RE1 /kernel: veriexec: no signatures for device. file='/usr/sbin/snmpd' dev=76554 inode=81436 uid=0 pid=2796
> Oct 20 16:27:20 RE1 /kernel: veriexec: no signatures for device. file='/usr/sbin/mgd' dev=76578 inode=75000 uid=0 pid=2797
> Oct 20 16:27:20 RE1 init: inet-process is thrashing, not restarted
> Oct 20 16:27:20 RE1 /kernel: veriexec: no signatures for device. file='/usr/sbin/cli' dev=76578 inode=74288 uid=0 pid=2813
> Oct 20 16:27:20 RE1 init: management is thrashing, not restarted
> Oct 20 16:27:20 RE1 /kernel: veriexec: no signatures for device. file='/usr/sbin/cli' dev=76578 ino
> --- JUNOS 7.5R3.1 built 2006-07-14 17:14:21 UTC
> Oct 20 16:27:20 RE1 /kernel: veriexec: no signatures for device. file='/usr/sbin/cli' dev=76578 inode=74288 uid=0 pid=2815
> Oct 20 16:27:20 RE1 /kernel: veriexec: no signatures for device. file='/usr/sbin/tnp.sntpd' dev=76554 inode=82290 uid=0 pid=2798
> Oct 20 16:27:20 RE1 /kernel: veriexec: no signatures for device. file='/usr/sbin/tnp.sntpc' dev=76554 inode=82164 uid=0 pid=2799
> Oct 20 16:27:20 RE1 /kernel: veriexec: no signatures for device. file='/usr/sbin/craftd' dev=76554 inode=75248 uid=0 pid=2800
> Oct 20 16:27:20 RE1 /kernel: veriexec: no signatures for device. file='/usr/sbin/alarmd' dev=76554 inode=73932 uid=0 pid=2801
> Oct 20 16:27:20 RE1 /kernel: veriexec: no signatures for device. file='/usr/sbin/chassisd' dev=76554 inode=74648 uid=0 pid=2802
> Oct 20 16:27:20 RE1 init: sntp is thrashing, not restarted
> Oct 20 16:27:20 RE1 /kernel: veriexec: no signatures for device. file='/usr/sbin/cli' dev=76578 inode=74288 uid=0 pid=2816
> Oct 20 16:27:20 RE1 init: chassis-control is thrashing, not restarted
> Oct 20 16:27:20 RE1 /kernel: veriexec: no signatures for device. file='/usr/sbin/cli' dev=76578 inode=74288 uid=0 pid=2817
> Oct 20 16:27:20 RE1 init: alarm-control is thrashing, not restartedlogin: /usr/sbin/cli: Authentication error
> Test_M20_RR
> RE1 (ttyd0)
> login:
>
>
>
> _______________________________________________
> juniper-nsp mailing list juniper-nsp at puck.nether.net
> https://puck.nether.net/mailman/listinfo/juniper-nsp
>
--
Erdem
More information about the juniper-nsp
mailing list