[j-nsp] BGP Configuration on J6350

Stacy W. Smith stacy at acm.org
Wed Oct 3 12:19:48 EDT 2007


Sounds like it's working as designed. Remember that a BGP neighbor  
only advertises the routes it's selected as best. In your case it  
sounds like the J6350 has only selected 6141 prefixes that it  
received from ISP3 as the best path, and is therefore only re- 
advertising those 6141 prefixes to the GSR. Presumably the J6350 has  
selected the path via the GSR for the remainder of its prefixes. If  
you want a different behavior you would need to modify which paths  
are being preferred via policy on one or both of your BGP-speaking  
routers.

--Stacy

On  3 Oct 2007, at 10:08 AM, Eric Van Tol wrote:

> Try doing a 'show route advertising-protocol bgp x.x.x.x', where  
> x.x.x.x
> is the GSR address.  It's quite possible that it is already sending a
> full table and the GSR just isn't showing the inactive routes.  I  
> can't
> remember what the default behavior is of Cisco, in terms of showing
> routes received in 'show ip bgp summary'.
>
> If you want to be sure, however, you can do the following:
>
> policy-statement internal {
>     term term1 {
>         from protocol bgp;
>         }
>         then nexthop self;
>     }
> }
>
> That will re-advertise all routes learned through BGP to any peer on
> which you've applied this policy.
>
> -evt
>
>
>> -----Original Message-----
>> From: juniper-nsp-bounces at puck.nether.net
>> [mailto:juniper-nsp-bounces at puck.nether.net] On Behalf Of
>> Matthew Crocker
>> Sent: Wednesday, October 03, 2007 12:03 PM
>> To: juniper-nsp at puck.nether.net
>> Subject: [j-nsp] BGP Configuration on J6350
>>
>>
>> Hello,
>>
>>   I'm new to JUNOS please bear with me.
>>
>> I have the following network setup
>>
>> ISP1 (AS7018)  connected via OC-3 to GSR
>> ISP2 (AS1239) connected via GigE to GSR
>> ISP3 (AS16657) connected via GigE to J6350
>>
>> I have a GigE between the J6350 & GSR,  My AS7849
>>
>> BGP with full tables running to all 3 ISPs
>>
>> ISP1 shows 227638 prefixes received (GSR)
>> ISP2 shows 228612 prefixes received (GSR)
>> ISP3 shows 227904 prefixes received (GSR)
>>
>> The J6350 is seeing 225992 prefixes from the GSR
>> The GSR is only seeing 6141 prefixes from  the J6350
>>
>> How do I configure the J6350 to send the full table to its IGP peer?
>>
>> show bgp summary shows
>> show bgp summary
>> Groups: 2 Peers: 2 Down peers: 0
>> Table          Tot Paths  Act Paths Suppressed    History Damp
>> State    Pending
>> inet.0            453826     229366          0          0
>> 0          0
>> Peer               AS      InPkt     OutPkt    OutQ   Flaps Last Up/
>> Dwn State|#Active/Received/Damped...
>> XXXXXXXX 7849      72875      14981       0       6       45:22
>> 223250/225922/0      0/0/0
>> XXXXXXXX 16657      41920        113       0       2       53:53
>> 6116/227904/0        0/0/0
>>
>> show configuration protocols bgp
>> path-selection always-compare-med;
>> local-as 7849;
>> group internal-within-AS7849 {
>>      type internal;
>>      local-address <ge-0/0/0.0 IP address>;
>>      export internal;
>>      graceful-restart;
>>      neighbor <GSR IP ADDRESS>;
>> }
>> group FiberTech {
>>      type external;
>>      export pl-announce;
>>      peer-as 16657;
>>      neighbor <FIBERTECH IP ADDRESS>;
>> }
>>
>> show policy internal
>> Policy internal:
>>      Term term1:
>>          then nexthop self
>>
>>
>>
>>
>> _______________________________________________
>> juniper-nsp mailing list juniper-nsp at puck.nether.net
>> https://puck.nether.net/mailman/listinfo/juniper-nsp
>>
> _______________________________________________
> juniper-nsp mailing list juniper-nsp at puck.nether.net
> https://puck.nether.net/mailman/listinfo/juniper-nsp



More information about the juniper-nsp mailing list