[j-nsp] Telnet e320

[Nitin Vig]

AFAIK, it's been there for a long time. Yes SSH to the VR works too.
Configuring the SSH config commands in the VR should do.

http://www.juniper.net/techpubs/software/erx/junose82/swconfig-system-ba
sics/html/passwords-security-config8.html#1032536

Regards,
Nitin
-----Original Message-----
From: Richmond, Jeff [mailto:Jeff.Richmond at frontiercorp.com] 
Sent: Monday, January 28, 2008 9:13 PM
To: Nitin Vig; sunnyday; Juniper-Nsp
Subject: RE: [j-nsp] Telnet e320

Interesting, has that always been there? Funny, nobody at Juniper seemed
to know about it when I asked. I did just confirm it was there though,
but any idea if there is a corresponding SSH command of some sorts?

Thanks,
-Jeff
________________________________________
From: Nitin Vig [nitinvig at juniper.net]
Sent: Monday, January 28, 2008 7:12 AM
To: Richmond, Jeff; sunnyday; Juniper-Nsp
Subject: RE: [j-nsp] Telnet e320

Not true.....You can use 'telnet listen' command in the VR.

1440-2:t1#sh ip int br
     Interface           IP-Address        Status    Protocol
Description
-------------------- ------------------- ---------- -----------
---------------
null0                255.255.255.255/32  up         up

FastEthernet0/0.20   10.10.10.1/24       up         up

1440-2:t1#
1440-2:t1#ping 10.10.10.2
Sending 5 ICMP echoes to 10.10.10.2, timeout = 2 sec.
!!!!!
Success rate = 100% (5/5), round-trip min/avg/max = 1/3/12 ms
1440-2:t1#telnet 10.10.10.2
1440-2:t1#
1440-2:t1#conf t
Enter configuration commands, one per line.  End with ^Z.
1440-2:t1(config)#vir t2
1440-2:t2(config)#telnet listen
1440-2:t2(config)#^Z
1440-2:t2#vir t1
1440-2:t1#telnet 10.10.10.2

Logged in on vty 1 via telnet.
Copyright (c) 1999-2007 Juniper Networks, Inc.  All rights reserved.

1440-2:t2>
1440-2:t2>
1440-2:t2>exit
Logging out.


1440-2:t1#

Regards,
Nitin

-----Original Message-----
From: juniper-nsp-bounces at puck.nether.net
[mailto:juniper-nsp-bounces at puck.nether.net] On Behalf Of Richmond, Jeff
Sent: Monday, January 28, 2008 7:38 PM
To: sunnyday; Juniper-Nsp
Subject: Re: [j-nsp] Telnet e320

Unless something has changed in recent code versions, you cannot
Telnet/SSH in to a VR other than Default. This is very annoying to say
the least...

-Jeff
________________________________________
From: juniper-nsp-bounces at puck.nether.net
[juniper-nsp-bounces at puck.nether.net] On Behalf Of sunnyday
[cscosunny at gmail.com]
Sent: Monday, January 28, 2008 1:28 AM
To: Juniper-Nsp
Subject: [j-nsp] Telnet e320

hello
i want to know if i can telnet to a virtual router configured on the box
since the only way i do it now is through the default virtual router, is
this possible?
thanks in advance
_______________________________________________
juniper-nsp mailing list juniper-nsp at puck.nether.net
https://puck.nether.net/mailman/listinfo/juniper-nsp
_______________________________________________
juniper-nsp mailing list juniper-nsp at puck.nether.net
https://puck.nether.net/mailman/listinfo/juniper-nsp