[j-nsp] flexible-ethernet-services on 1000 LH interfaces
Jonas Frey
jf at probe-networks.de
Wed Oct 15 10:31:22 EDT 2008
Dan,
flexible-ethernet-encap is only supported on SFP interfaces (except for
the M7i builtin-ge which doesnt support it). If you have fixed optics
interfaces this is not supported.
Regards,
Jonas
On Wed, 2008-10-15 at 14:58, Dan Benson wrote:
> All,
>
> I am trying to build l2circuits between a few junipers in my network
> without any luck. In my test case I have M20s with dual LH optic GIGe
> interfaces facing a cisco cat 6500 using 802.3ad where I then have
> vlans hanging off said switch to service downstream transit customers
> and, I was hoping, possible transport customers.
>
> Router A:
> ge-0/1/0 {
> gigether-options {
> 802.3ad ae0;
> }
> }
> ge-0/2/0 {
> gigether-options {
> 802.3ad ae0;
> }
> ae0 {
> vlan-tagging;
> mtu 9100;
> encapsulation flexible-ethernet-services;
> aggregated-ether-options {
> link-speed 1g;
> }
> unit 600 {
> encapsulation vlan-ccc;
> vlan-id 600;
> }
>
> show configuration protocols l2circuit:
> neighbor (neighbor lo0) {
> interface ae0.600 {
> virtual-circuit-id 600;
> no-control-word;
> }
> }
>
> show l2circuit connections:
> Layer-2 Circuit Connections:
>
> Legend for connection status (St)
> EI -- encapsulation invalid NP -- interface h/w not present
> MM -- mtu mismatch Dn -- down
> EM -- encapsulation mismatch VC-Dn -- Virtual circuit Down
> CM -- control-word mismatch Up -- operational
> VM -- vlan id mismatch CF -- Call admission control failure
> OL -- no outgoing label XX -- unknown
> NC -- intf encaps not CCC/TCC
> CB -- rcvd cell-bundle size bad
>
> Legend for interface status
> Up -- operational
> Dn -- down
> Neighbor: (neighbor lo0)
> Interface Type St Time last up # Up
> trans
> ae0.600(vc 600) rmt Up Oct 10 11:49:07
> 2008 1
> Local interface: ae0.600, Status: Up, Encapsulation: VLAN
> Remote PE: 1(neighbor lo0), Negotiated control-word: No
> Incoming label: 275138, Outgoing label: 738273
>
> Router B:
> ge-1/0/0 {
> gigether-options {
> 802.3ad ae0;
> }
> }
> ge-2/0/0 {
> gigether-options {
> 802.3ad ae0;
> }
> }
> ae0 {
> vlan-tagging;
> mtu 9100;
> encapsulation flexible-ethernet-services;
> }
> unit 600 {
> encapsulation vlan-ccc;
> vlan-id 600;
> }
> }
>
> show configuration protocols l2circuit:
> neighbor (neighbor lo0) {
> interface ae0.600 {
> virtual-circuit-id 600;
> no-control-word;
> }
> }
>
> show l2circuit connections:
> Layer-2 Circuit Connections:
>
> Legend for connection status (St)
> EI -- encapsulation invalid NP -- interface h/w not present
> MM -- mtu mismatch Dn -- down
> EM -- encapsulation mismatch VC-Dn -- Virtual circuit Down
> CM -- control-word mismatch Up -- operational
> VM -- vlan id mismatch CF -- Call admission control failure
> OL -- no outgoing label XX -- unknown
> NC -- intf encaps not CCC/TCC
> CB -- rcvd cell-bundle size bad
>
> Legend for interface status
> Up -- operational
> Dn -- down
> Neighbor: (neighbor lo0)
> Interface Type St Time last up # Up
> trans
> ae0.600(vc 600) rmt Up Oct 10 10:49:09
> 2008 1
> Local interface: ae0.600, Status: Up, Encapsulation: VLAN
> Remote PE: (neighbor lo0), Negotiated control-word: No
> Incoming label: 738273, Outgoing label: 275138
>
> MPLS in my network is running without flaw thus far and I have tested
> the intercommunication between the M20's and the Cat6500s on both
> sides, all working as one would expect. Do these LH GIGe interfaces
> not support Flexibility? Do I need to add the "flexible-ethernet-
> services" to each interface in the ae?
>
> That you much for your time in advance. //db
>
>
>
>
>
> _______________________________________________
> juniper-nsp mailing list juniper-nsp at puck.nether.net
> https://puck.nether.net/mailman/listinfo/juniper-nsp
More information about the juniper-nsp
mailing list