[j-nsp] Logical Interfaces 802.1ad

[Onam Rubio]

Hello Experts,

In the diagram topology I am working with the VMAN tag 50. I made some test with a CISCO router and it works.

I check the jumbo-frame at the summit side and is enable to all ports.

> Date: Mon, 19 Oct 2009 10:47:16 +0300
> From: evgeniy at ip.datagroup.ua
> To: onamrubio at hotmail.com
> CC: juniper-nsp at puck.nether.net
> Subject: Re[2]: [j-nsp] Logical Interfaces 802.1ad
> 
> Also works fine:
> 
> {master}[edit interfaces xe-4/1/0]
> evgeniy at mx480# show
> description "=== Summit X650 test ===";
> flexible-vlan-tagging;
> encapsulation flexible-ethernet-services;
> gigether-options {
>     ethernet-switch-profile {
>         tag-protocol-id 0x88a8;
>     }
> }
> unit 100 {
>     description "=== Summit X650 test ===";
>     vlan-tags outer 0x88a8.4092 inner 100;
>     family inet {
>         address x.x.x.x/30;
>     }
> }
> 
>  Summit:
>  enable jumbo-frame ports all
> 
> 
> best regards,
> -- 
> Evgeniy Aikashev
> network engineer
> JSC DATAGROUP
> 
> Monday, October 19, 2009, 10:17:22 AM, Onam wrote:
> > Hello Evgeniy,
> 
> > I made some test before with this ethertype and it works. The Extreme x450 use both of them
> > 0x8100 for VLAN and 0x88a8 for VMAN so if i do that the VMAN will become a VLAN.
> 
> > I see that by default the Juniper router M10 use ethertype 0x8100, but when I try to use
> > ethertype 0x88a8 the devices doens't see each other, I run a ping to the other side with no response.
> 
> 
> >> Date: Mon, 19 Oct 2009 09:58:23 +0300
> >> From: evgeniy at ip.datagroup.ua
> >> To: onamrubio at hotmail.com
> >> CC: juniper-nsp at puck.nether.net
> >> Subject: Re: [j-nsp] Logical Interfaces 802.1ad
> >> 
> >> Hello Onam,
> >> try to change ethertype from Summit side:
> >> 
> >> configure vman ethertype 0x8100
> >> 
> >> best regards,
> >> -- 
> >> Evgeniy Aikashev
> >> network engineer
> >> JSC DATAGROUP
> >> 
> >> Monday, October 19, 2009, 3:30:51 AM, Onam wrote:
> >> 
> >> > Hi experts,
> >> 
> >> > I want to make logical interfaces on a physical interface ge-0/2/0 of a Juniper M10 router to
> >> > connected to a the trunk port of a Summit Extreme x450 with the ethertype 0x88a8 (IEEE 802.1ad).
> >> 
> >> > I have the following configuration on the router.
> >> 
> >> > ge-0/2/0 {
> >> > vlan-tagging;
> >> > gigether-options {
> >> > ethernet-switch-profile {
> >> > tag-protocol-id 0x88a8;
> >> > }
> >> > }
> >> > unit 50 {
> >> > vlan-tags outer 0x88a8.50;
> >> > family inet {
> >> > address 192.168.175.169/28;
> >> > }
> >> > }
> >> > }
> >> 
> >> > I made the test with the 802.1q and it works but with 802.1ad didn't work.
> >> 
> >> > Best regards.
> >> > 
> >> > _________________________________________________________________
> >> > News, entertainment and everything you care about at Live.com. Get it now!
> >> > http://www.live.com/getstarted.aspx
> >> > _______________________________________________
> >> > juniper-nsp mailing list juniper-nsp at puck.nether.net
> >> > https://puck.nether.net/mailman/listinfo/juniper-nsp
> >> 
> 
> > Get news, entertainment and everything you care about at Live.com. Check it out! 
> 
 		 	   		  
_________________________________________________________________
News, entertainment and everything you care about at Live.com. Get it now!
http://www.live.com/getstarted.aspx