[j-nsp] logical router with physical Interco

[Cristian Frizziero]

Ok,

It looks like a hardware problem (at PIC or EFEB level, may be).
I´d be a good idea to change the cable too.... just in case....

Check with show log chassid , may be you can find some log related to a 
physical problem.

Also check with a show route logical-router PE2 or PE3. You must find 
your subnets and physical addresses of your interfaces. If you find some 
route marked as rejected you could think in some problem of connectivity 
in L1.

Good luck

logo impre
Ing. Cristian Frizziero
Honorio Pueyrredon 1475 -- Buenos Aires
Tel+54.11.4855.6041 (Ext.517)
Cel+54.9.11.6249.1303
cristian.frizziero at iquall.net <mailto:cristian.frizziero at iquall.net>
www.iquall.net <http://www.iquall.net>



El 21/12/2010 18:34, juniper light escribió:
> I didn't change cabling, but I connected a new interface to annother 
> router and I'm having the same problem, the new interface is in the 
> default configuration :
> set interfaces fe-0/3/2 unit 0 family inet address 10.0.24.2/30 
> <http://10.0.24.2/30>
> admin at M10 <mailto:admin at M10>> show interfaces terse
> Interface               Admin Link Proto    Local                 Remote
> ...
> fe-0/3/0                up    up
> fe-0/3/0.123            up    up   inet 10.0.123.1/30 
> <http://10.0.123.1/30>
> fe-0/3/0.32767          up    up
> fe-0/3/1                up    up
> fe-0/3/1.123            up    up   inet 10.0.123.2/30 
> <http://10.0.123.2/30>
> fe-0/3/1.32767          up    up
> fe-0/3/2                up    up
> fe-0/3/2.0              up    up   inet 10.0.24.2/30 <http://10.0.24.2/30>
> fe-0/3/3                up    up
> any idea guys ?
> BR // Mounir
>
>
> On Tue, Dec 21, 2010 at 7:25 PM, Cristian Frizziero 
> cristian.frizziero at iquall.net <mailto:cristian.frizziero at iquall.net> 
> wrote:
>
>     Hi!!
>
>     I'd try to change ports pairs, and to switch the PIC to a
>     different fpc slot, just to be sure that there is no hardware
>     issue....
>
>     The configuration looks fine....
>
>     Cristian
>
>
>     El 21/12/2010 15:07, juniper light escribió:
>>     Hi guys, I would like to use M10 to simulate 3 PE, using
>>     logical-routers ( Junos 8.4R4.2 ) I connected 2 fastethernet
>>     back-to-back, link are UP. but when I tried configuring vlan-id ,
>>     I cannot ping from one Logical router to the other : first
>>     scenario using Vlan-tagging : set logical-routers PE2 interfaces
>>     fe-0/3/0 unit 23 vlan-id 123 set logical-routers PE2 interfaces
>>     fe-0/3/0 unit 23 family inet address 10.0.123.1/30
>>     <http://10.0.123.1/30> set logical-routers PE3 interfaces
>>     fe-0/3/1 unit 23 vlan-id 123 set logical-routers PE3 interfaces
>>     fe-0/3/1 unit 23 family inet address 10.0.123.2/30
>>     <http://10.0.123.2/30> set interfaces fe-0/3/0 vlan-tagging set
>>     interfaces fe-0/3/1 vlan-tagging admin at M10> show interfaces terse
>>     Interface Admin Link Proto Local Remote ... fe-0/3/0 up up
>>     fe-0/3/0.123 up up inet 10.0.123.1/30 fe-0/3/0.32767
>>     <http://10.0.123.1/30fe-0/3/0.32767> up up fe-0/3/1 up up
>>     fe-0/3/1.123 up up inet 10.0.123.2/30 fe-0/3/1.32767
>>     <http://10.0.123.2/30fe-0/3/1.32767> up up fe-0/3/2 up up
>>     fe-0/3/3 up up Second scenario without Vlan-tagging : set
>>     logical-routers PE2 interfaces fe-0/3/0 unit 0 family inet
>>     address 10.0.123.1/30 <http://10.0.123.1/30> set logical-routers
>>     PE3 interfaces fe-0/3/1 unit 0 family inet address 10.0.123.2/30
>>     <http://10.0.123.2/30> admin at M10> ping logical-router PE2
>>     10.0.123.2 source 10.0.123.1 PING 10.0.123.2 (10.0.123.2): 56
>>     data bytes nothing happen ...... admin at M10> show interfaces terse
>>     Interface Admin Link Proto Local Remote ... fe-0/3/0 up up
>>     fe-0/3/0.0 up up inet 10.0.123.1/30 fe-0/3/1
>>     <http://10.0.123.1/30fe-0/3/1> up up fe-0/3/1.0 up up inet
>>     10.0.123.2/30 fe-0/3/2 <http://10.0.123.2/30fe-0/3/2> up up
>>     fe-0/3/3 up up admin at M10
>>     >  show chassis hardware
>>     Hardware inventory:
>>     Item             Version  Part number  Serial number     Description
>>     Chassis                                xxxx             M10
>>     Midplane         REV 03   710-001950   xxx            M10 Backplane
>>     Power Supply A   Rev 05   740-002497  xxx          AC Power Supply
>>     Display          REV 04   710-001995   xxx            M10 Display Board
>>     Routing Engine   REV 07   740-007603   xxx      RE-3.0
>>     FEB              REV 08   710-003310   xx            E-FEB
>>     FPC 0                                                    E-FPC
>>        PIC 1          REV 05   750-003163   xxx            1x G/E, 1000 BASE-SX
>>        PIC 3          REV 06   750-002992   xxx           4x F/E, 100 BASE-TX
>>     FPC 1                                                    E-FPC
>>     Fan Tray                                                 Rear Left Fan Tray
>>
>>     Any idea about that ?
>>
>>     Thanks for your help,
>>
>>     Kind Regards
>>     // Mounir
>>     _______________________________________________
>>     juniper-nsp mailing listjuniper-nsp at puck.nether.net  <mailto:juniper-nsp at puck.nether.net>
>>     https://puck.nether.net/mailman/listinfo/juniper-nsp
>
>