[j-nsp] EX4200 Problem - Bad Switch?

[Paul Stewart]

Hey folks


Ran across a weird issue today on a new EX4200-48T switch.  Switch boots up
and during so I see this (sorry for the length of the post):

Trying to mount root from ufs:/dev/da0s1a
Attaching /packages/jbase via /dev/mdctl...
Mounted jbase package on /dev/md0...
Verified manifest signed by PackageProduction_10_0_0
Verified jboot signed by PackageProduction_10_0_0
Verified jbase-10.0R4.7 signed by PackageProduction_10_0_0
/packages/jcrypto-ex-10.0R4.7 not present.
/packages/jdocs-ex-10.0R4.7 not present.
Mounted jkernel-ex package on /dev/md1...
Verified manifest signed by PackageProduction_10_0_0
Verified jkernel-ex-10.0R4.7 signed by PackageProduction_10_0_0
Mounted jpfe-ex42x package on /dev/md2...
Verified manifest signed by PackageProduction_10_0_0
Verified jpfe-ex42x-10.0R4.7 signed by PackageProduction_10_0_0
Mounted jroute-ex package on /dev/md3...
Verified manifest signed by PackageProduction_10_0_0
Verified jroute-ex-10.0R4.7 signed by PackageProduction_10_0_0
/packages/jswitch-ex-10.0R4.7 not present.
Mounted jweb-ex package on /dev/md4...
Verified manifest signed by PackageProduction_10_0_0
Verified jweb-ex-10.0R4.7 signed by PackageProduction_10_0_0
Executing /packages/mnt/jweb-ex-10.0R4.7/mount.post..
Automatic reboot in progress...
FILE SYSTEM CLEAN; SKIPPING CHECKS
clean, 48430 free (46 frags, 6048 blocks, 0.0% fragmentation)
FILE SYSTEM CLEAN; SKIPPING CHECKS
clean, 28254 free (38 frags, 3527 blocks, 0.1% fragmentation)
FILE SYSTEM CLEAN; SKIPPING CHECKS
clean, 62228 free (244 frags, 7748 blocks, 0.4% fragmentation)
FILE SYSTEM CLEAN; SKIPPING CHECKS
clean, 160996 free (28 frags, 20121 blocks, 0.0% fragmentation)
FILE SYSTEM CLEAN; SKIPPING CHECKS
clean, 160996 free (28 frags, 20121 blocks, 0.0% fragmentation)
Creating initial configuration...mgd: error: Couldn't open lib
"/usr/lib/dd//libjcrypto-dd.so": Cannot open "/usr/lib/dd//libjcrypto-dd.so"
mgd: error: Couldn't open lib "/usr/lib/dd//libjcrypto_junos-dd.so": Cannot
open "/usr/lib/dd//libjcrypto_junos-dd.so"
mgd: error: Couldn't open lib "/usr/lib/dd//libjdocs-dd.so": Cannot open
"/usr/lib/dd//libjdocs-dd.so"
/config/juniper.conf:294:(8) syntax error at 'rstp'
  [edit protocols]
    'rstp;'
      syntax error
/config/juniper.conf:297:(5) error recovery ignores input until this point
at '}'
  [edit protocols]
    '}'
      error recovery ignores input until this point
/config/juniper.conf:300:(5) error recovery ignores input until this point
at '}'
  [edit protocols]
    '}'
      error recovery ignores input until this point
/config/juniper.conf:304:(1) error recovery ignores input until this point
at '}'
  [edit]
    '}'
      error recovery ignores input until this point
[edit system services ssh]
  'ssh'
    warning: daemon binary /usr/sbin/sshd not found
mgd: commit complete
Setting initial options:  debugger_on_panic=NO debugger_on_break=NO.
Starting optional daemons: OK: extracted home directories.
.
Doing initial network setup:
.
Initial interface configuration:
additional daemons:.
Additional routing options:kern.module_path: /boot//kernel;/bootLoading the
NETPFE ethernet module
/modules -> /booLoading the EX-series platform NETPFE module
t//kernel;/boot/modules;/modules
grat_arp_on_ifup=YES: net.link.ether.inet.grat_arp_on_ifup: 1 -> 1
grat_arp_delay=${grat_arp_delay}: net.link.ether.inet.grat_arp_delay: 0 -> 0
kld netpfe drv: ifpfed_ethkld platform: ex_ifpfe if_vcpkern.module_path:
/boot//kernel;/boot/modules;/modules ->
/boot//kernel;/boot/modules;/modules;/modules/peertype
kld peertype: peertype_hcm peertype_pfem peertype_sfi peertype_slavere.
Doing additional network setup:.
Starting final network daemons:.
setting ldconfig path: /usr/lib /opt/lib
ldconfig: warning: /opt/lib: No such file or directory
starting standard daemons: cron.
Local package initialization:.
kern.securelevel: -1 -> 1
starting local daemons:.
Thu Oct 14 06:24:18 UTC 2010

Amnesiac (ttyu0)



So I thought that perhaps the JunOS install is corrupt and rebooted with my
USB drive connected.  Ran through the installation and it won’t complete:


loader> install file:///jinstall-ex-4200-10.0R4.7-domestic-signed.tgz
Package /jinstall-ex-4200-10.0R4.7-domestic-signed.tgz is signed...
/kernel data=0x4efa0c+0x51a94 syms=[0x4+0x4e100+0x4+0x707d3]
Kernel entry at 0xa00000e0 ...
GDB: no debug ports present
KDB: debugger backends: ddb
KDB: current backend: ddb
platform_early_bootinit: EX Series Early Boot Initialization
Copyright (c) 1996-2010, Juniper Networks, Inc.
All rights reserved.
Copyright (c) 1992-2006 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
JUNOS 10.0R4.7 #0: 2010-08-22 02:45:23 UTC
   
builder at ormonth.juniper.net:/volume/build/junos/10.0/release/10.0R4.7/obj-po
Timecounter "decrementer" frequency 50000000 Hz quality 0
cpu0: Freescale e500v2 core revision 2.2
cpu0: HID0 80004080<EMCP,TBEN,EN_MAS7_UPDATE>
real memory  = 1044381696 (996 MB)
avail memory = 1022767104 (975 MB)
ETHERNET SOCKET BRIDGE initialising
Initializing EXSERIES platform properties ...
nexus0: <PPC e500 Nexus device>
ocpbus0: <on-chip peripheral bus> on nexus0
openpic0: <OpenPIC in on-chip peripheral bus> iomem 0xfef40000-0xfef600b3 on
ocpbus0
uart0: <16550 or compatible> iomem 0xfef04500-0xfef0450f irq 58 on ocpbus0
uart0: console (9600,n,8,1)
uart1: <16550 or compatible> iomem 0xfef04600-0xfef0460f irq 58 on ocpbus0
lbc0: <Freescale 8533 Local Bus Controller> iomem
0xfef05000-0xfef05fff,0xff000000-0xffffffff irq 22 on ocpbus0
cfi0: <AMD/Fujitsu - 8MB> iomem 0xff800000-0xffffffff on lbc0
syspld0 iomem 0xff000000-0xff00ffff on lbc0
tsec0: <eTSEC ethernet controller> iomem 0xfef24000-0xfef24fff irq 45,46,50
on ocpbus0
tsec0: hardware MAC address b0:c6:9a:61:96:7f
miibus0: <MII bus> on tsec0
e1000phy0: <Marvell 88E1112 Gigabit PHY> on miibus0
e1000phy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX-FDX,
auto
pcib0: <Freescale MPC8544 PCI host controller> iomem
0xfef08000-0xfef08fff,0xf0000000-0xf3ffffff on ocpbus0
pci0: <PCI bus> on pcib0
pci0: <serial bus, USB> at device 18.0 (no driver attached)
ehci0: <Philips ISP156x USB 2.0 controller> mem 0xf0001000-0xf00010ff irq 22
at device 18.2 on pci0
usb0: EHCI version 1.0
usb0: <Philips ISP156x USB 2.0 controller> on ehci0
usb0: USB revision 2.0
uhub0: Philips EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
umass0: STMicroelectronics ST72682  High Speed Mode, rev 2.00/2.10, addr 2
umass1: SanDisk MobileMate Micro, rev 2.00/94.07, addr 3
pcib1: <Freescale MPC8544 PCI Express host controller> iomem
0xfef0a000-0xfef0afff,0xe0000000-0xe3ffffff,0xec000000-0xec0fffff irq 42 on
ocpbus0
pci1: <PCI bus> on pcib1
pcib2: <PCI-PCI bridge> at device 0.0 on pci1
pci2: <PCI bus> on pcib2
pci2: <memory> at device 0.0 (no driver attached)
pcib3: <Freescale MPC8544 PCI Express host controller> iomem
0xfef09000-0xfef09fff,0xe4000000-0xe7ffffff,0xec100000-0xec1fffff irq 41 on
ocpbus0
pci3: <PCI bus> on pcib3
pcib4: <PCI-PCI bridge> at device 0.0 on pci3
pci4: <PCI bus> on pcib4
pci4: <memory> at device 0.0 (no driver attached)
pcib5: <Freescale MPC8544 PCI Express host controller> iomem
0xfef0b000-0xfef0bfff,0xe8000000-0xebffffff,0xec200000-0xec2fffff irq 43 on
ocpbus0
pci5: <PCI bus> on pcib5
pcib6: <PCI-PCI bridge> at device 0.0 on pci5
pci6: <PCI bus> on pcib6
pci6: <memory> at device 0.0 (no driver attached)
i2c0: <MPC85XX OnChip i2c controller> iomem 0xfef03000-0xfef03014 irq 59 on
ocpbus0
i2c1: <MPC85XX OnChip i2c controller> iomem 0xfef03100-0xfef03114 irq 59 on
ocpbus0
Timecounters tick every 10.000 msec
md0: Preloaded image </isofs-install-ex> 10477568 bytes at 0xa05ffd7c
da1 at umass-sim1 bus 1 target 0 lun 0
da1: <Generic STORAGE DEVICE 9407> Removable Direct Access SCSI-0 device
da1: 40.000MB/s transfers
da1: 1910MB (3911680 512 byte sectors: 255H 63S/T 243C)
da0 at umass-sim0 bus 0 target 0 lun 0
da0: <ST ST72682 2.10> Removable Direct Access SCSI-2 device
da0: 40.000MB/s transfers
da0: 1000MB (2048000 512 byte sectors: 64H 32S/T 1000C)
Trying to mount root from cd9660:/dev/md0
FILE SYSTEM CLEAN; SKIPPING CHECKS
clean, 160996 free (28 frags, 20121 blocks, 0.0% fragmentation)
tunefs: soft updates remains unchanged as disabled
FILE SYSTEM CLEAN; SKIPPING CHECKS
clean, 28254 free (38 frags, 3527 blocks, 0.1% fragmentation)
/dev/da0s2a: 187.2MB (383352 sectors) block size 16384, fragment size 2048
        using 4 cylinder groups of 46.80MB, 2995 blks, 6016 inodes.
        with soft updates
super-block backups (for fsck -b #) at:
32, 95872, 191712, 287552
/dev/da0s2f: 124.8MB (255584 sectors) block size 16384, fragment size 2048
        using 4 cylinder groups of 31.20MB, 1997 blks, 4096 inodes.
        with soft updates
super-block backups (for fsck -b #) at:
32, 63936, 127840, 191744
Installing disk1:/jinstall-ex-4200-10.0R4.7-domestic-signed.tgz
/dev/da0s3d: 319.6MB (654524 sectors) block size 16384, fragment size 2048
        using 4 cylinder groups of 79.91MB, 5114 blks, 10240 inodes.
super-block backups (for fsck -b #) at:
32, 163680, 327328, 490976
tty: not found
tty: not found
tty: not found
tty: not found
date: connect: Can't assign requested address
Checking package integrity...
Verified SHA1 checksum of jbase-ex-10.0R4.7.tgz
Verified SHA1 checksum of jboot-ex-10.0R4.7.tgz
Verified SHA1 checksum of jcrypto-ex-10.0R4.7.tgz
Verified SHA1 checksum of jdocs-ex-10.0R4.7.tgz
Verified SHA1 checksum of jkernel-ex-10.0R4.7.tgz
Verified SHA1 checksum of jpfe-ex42x-10.0R4.7.tgz
Verified SHA1 checksum of jroute-ex-10.0R4.7.tgz
Verified SHA1 checksum of jswitch-ex-10.0R4.7.tgz
Verified SHA1 checksum of jweb-ex-10.0R4.7.tgz
Running requirements check first for jbundle-ex-4200-10.0R4.7-domestic...
Running pre-install for jbundle-ex-4200-10.0R4.7-domestic...
Installing jbundle-ex-4200-10.0R4.7-domestic in
/tmp/pa2398.26/jbundle-ex-4200-10.0R4.7-domestic.x2398...
Running post-install for jbundle-ex-4200-10.0R4.7-domestic...
Adding jkernel-ex...
Adding jcrypto-ex...
Adding jdocs-ex...
Adding jswitch-ex...
Adding jpfe-ex42x...
Adding jroute-ex...
Adding jweb-ex...
Saving home directories
*** The installer exited with status 2 ***
*** The installation is unsuccessful!!! ***
A shell has been started. type exit<cr> to reboot:


Is this a bad switch??

Thanks in advance,

Paul