[j-nsp] EX4200 Problem - Bad Switch?

[Joe Hamelin]

It looks like you're missing a few libraries (files) in your install.
Re-install JunOS.

--
Joe Hamelin, W7COM, Tulalip, WA, 360-474-7474



On Mon, Jan 10, 2011 at 12:53 PM, Paul Stewart <paul at paulstewart.org> wrote:
> Hey folks…
>
> Ran across a weird issue today on a new EX4200-48T switch.  Switch boots up
> and during so I see this (sorry for the length of the post):
>
> Trying to mount root from ufs:/dev/da0s1a
> Attaching /packages/jbase via /dev/mdctl...
> Mounted jbase package on /dev/md0...
> Verified manifest signed by PackageProduction_10_0_0
> Verified jboot signed by PackageProduction_10_0_0
> Verified jbase-10.0R4.7 signed by PackageProduction_10_0_0
> /packages/jcrypto-ex-10.0R4.7 not present.
> /packages/jdocs-ex-10.0R4.7 not present.
> Mounted jkernel-ex package on /dev/md1...
> Verified manifest signed by PackageProduction_10_0_0
> Verified jkernel-ex-10.0R4.7 signed by PackageProduction_10_0_0
> Mounted jpfe-ex42x package on /dev/md2...
> Verified manifest signed by PackageProduction_10_0_0
> Verified jpfe-ex42x-10.0R4.7 signed by PackageProduction_10_0_0
> Mounted jroute-ex package on /dev/md3...
> Verified manifest signed by PackageProduction_10_0_0
> Verified jroute-ex-10.0R4.7 signed by PackageProduction_10_0_0
> /packages/jswitch-ex-10.0R4.7 not present.
> Mounted jweb-ex package on /dev/md4...
> Verified manifest signed by PackageProduction_10_0_0
> Verified jweb-ex-10.0R4.7 signed by PackageProduction_10_0_0
> Executing /packages/mnt/jweb-ex-10.0R4.7/mount.post..
> Automatic reboot in progress...
> FILE SYSTEM CLEAN; SKIPPING CHECKS
> clean, 48430 free (46 frags, 6048 blocks, 0.0% fragmentation)
> FILE SYSTEM CLEAN; SKIPPING CHECKS
> clean, 28254 free (38 frags, 3527 blocks, 0.1% fragmentation)
> FILE SYSTEM CLEAN; SKIPPING CHECKS
> clean, 62228 free (244 frags, 7748 blocks, 0.4% fragmentation)
> FILE SYSTEM CLEAN; SKIPPING CHECKS
> clean, 160996 free (28 frags, 20121 blocks, 0.0% fragmentation)
> FILE SYSTEM CLEAN; SKIPPING CHECKS
> clean, 160996 free (28 frags, 20121 blocks, 0.0% fragmentation)
> Creating initial configuration...mgd: error: Couldn't open lib
> "/usr/lib/dd//libjcrypto-dd.so": Cannot open "/usr/lib/dd//libjcrypto-dd.so"
> mgd: error: Couldn't open lib "/usr/lib/dd//libjcrypto_junos-dd.so": Cannot
> open "/usr/lib/dd//libjcrypto_junos-dd.so"
> mgd: error: Couldn't open lib "/usr/lib/dd//libjdocs-dd.so": Cannot open
> "/usr/lib/dd//libjdocs-dd.so"
> /config/juniper.conf:294:(8) syntax error at 'rstp'
>   [edit protocols]
>     'rstp;'
>       syntax error
> /config/juniper.conf:297:(5) error recovery ignores input until this point
> at '}'
>   [edit protocols]
>     '}'
>       error recovery ignores input until this point
> /config/juniper.conf:300:(5) error recovery ignores input until this point
> at '}'
>   [edit protocols]
>     '}'
>       error recovery ignores input until this point
> /config/juniper.conf:304:(1) error recovery ignores input until this point
> at '}'
>   [edit]
>     '}'
>       error recovery ignores input until this point
> [edit system services ssh]
>   'ssh'
>     warning: daemon binary /usr/sbin/sshd not found
> mgd: commit complete
> Setting initial options:  debugger_on_panic=NO debugger_on_break=NO.
> Starting optional daemons: OK: extracted home directories.
> .
> Doing initial network setup:
> .
> Initial interface configuration:
> additional daemons:.
> Additional routing options:kern.module_path: /boot//kernel;/bootLoading the
> NETPFE ethernet module
> /modules -> /booLoading the EX-series platform NETPFE module
> t//kernel;/boot/modules;/modules
> grat_arp_on_ifup=YES: net.link.ether.inet.grat_arp_on_ifup: 1 -> 1
> grat_arp_delay=${grat_arp_delay}: net.link.ether.inet.grat_arp_delay: 0 -> 0
> kld netpfe drv: ifpfed_ethkld platform: ex_ifpfe if_vcpkern.module_path:
> /boot//kernel;/boot/modules;/modules ->
> /boot//kernel;/boot/modules;/modules;/modules/peertype
> kld peertype: peertype_hcm peertype_pfem peertype_sfi peertype_slavere.
> Doing additional network setup:.
> Starting final network daemons:.
> setting ldconfig path: /usr/lib /opt/lib
> ldconfig: warning: /opt/lib: No such file or directory
> starting standard daemons: cron.
> Local package initialization:.
> kern.securelevel: -1 -> 1
> starting local daemons:.
> Thu Oct 14 06:24:18 UTC 2010
>
> Amnesiac (ttyu0)
>
>
>
> So I thought that perhaps the JunOS install is corrupt and rebooted with my
> USB drive connected.  Ran through the installation and it won’t complete:
>
>
> loader> install file:///jinstall-ex-4200-10.0R4.7-domestic-signed.tgz
> Package /jinstall-ex-4200-10.0R4.7-domestic-signed.tgz is signed...
> /kernel data=0x4efa0c+0x51a94 syms=[0x4+0x4e100+0x4+0x707d3]
> Kernel entry at 0xa00000e0 ...
> GDB: no debug ports present
> KDB: debugger backends: ddb
> KDB: current backend: ddb
> platform_early_bootinit: EX Series Early Boot Initialization
> Copyright (c) 1996-2010, Juniper Networks, Inc.
> All rights reserved.
> Copyright (c) 1992-2006 The FreeBSD Project.
> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
>         The Regents of the University of California. All rights reserved.
> JUNOS 10.0R4.7 #0: 2010-08-22 02:45:23 UTC
>
> builder at ormonth.juniper.net:/volume/build/junos/10.0/release/10.0R4.7/obj-po
> Timecounter "decrementer" frequency 50000000 Hz quality 0
> cpu0: Freescale e500v2 core revision 2.2
> cpu0: HID0 80004080<EMCP,TBEN,EN_MAS7_UPDATE>
> real memory  = 1044381696 (996 MB)
> avail memory = 1022767104 (975 MB)
> ETHERNET SOCKET BRIDGE initialising
> Initializing EXSERIES platform properties ...
> nexus0: <PPC e500 Nexus device>
> ocpbus0: <on-chip peripheral bus> on nexus0
> openpic0: <OpenPIC in on-chip peripheral bus> iomem 0xfef40000-0xfef600b3 on
> ocpbus0
> uart0: <16550 or compatible> iomem 0xfef04500-0xfef0450f irq 58 on ocpbus0
> uart0: console (9600,n,8,1)
> uart1: <16550 or compatible> iomem 0xfef04600-0xfef0460f irq 58 on ocpbus0
> lbc0: <Freescale 8533 Local Bus Controller> iomem
> 0xfef05000-0xfef05fff,0xff000000-0xffffffff irq 22 on ocpbus0
> cfi0: <AMD/Fujitsu - 8MB> iomem 0xff800000-0xffffffff on lbc0
> syspld0 iomem 0xff000000-0xff00ffff on lbc0
> tsec0: <eTSEC ethernet controller> iomem 0xfef24000-0xfef24fff irq 45,46,50
> on ocpbus0
> tsec0: hardware MAC address b0:c6:9a:61:96:7f
> miibus0: <MII bus> on tsec0
> e1000phy0: <Marvell 88E1112 Gigabit PHY> on miibus0
> e1000phy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX-FDX,
> auto
> pcib0: <Freescale MPC8544 PCI host controller> iomem
> 0xfef08000-0xfef08fff,0xf0000000-0xf3ffffff on ocpbus0
> pci0: <PCI bus> on pcib0
> pci0: <serial bus, USB> at device 18.0 (no driver attached)
> ehci0: <Philips ISP156x USB 2.0 controller> mem 0xf0001000-0xf00010ff irq 22
> at device 18.2 on pci0
> usb0: EHCI version 1.0
> usb0: <Philips ISP156x USB 2.0 controller> on ehci0
> usb0: USB revision 2.0
> uhub0: Philips EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
> uhub0: 2 ports with 2 removable, self powered
> umass0: STMicroelectronics ST72682  High Speed Mode, rev 2.00/2.10, addr 2
> umass1: SanDisk MobileMate Micro, rev 2.00/94.07, addr 3
> pcib1: <Freescale MPC8544 PCI Express host controller> iomem
> 0xfef0a000-0xfef0afff,0xe0000000-0xe3ffffff,0xec000000-0xec0fffff irq 42 on
> ocpbus0
> pci1: <PCI bus> on pcib1
> pcib2: <PCI-PCI bridge> at device 0.0 on pci1
> pci2: <PCI bus> on pcib2
> pci2: <memory> at device 0.0 (no driver attached)
> pcib3: <Freescale MPC8544 PCI Express host controller> iomem
> 0xfef09000-0xfef09fff,0xe4000000-0xe7ffffff,0xec100000-0xec1fffff irq 41 on
> ocpbus0
> pci3: <PCI bus> on pcib3
> pcib4: <PCI-PCI bridge> at device 0.0 on pci3
> pci4: <PCI bus> on pcib4
> pci4: <memory> at device 0.0 (no driver attached)
> pcib5: <Freescale MPC8544 PCI Express host controller> iomem
> 0xfef0b000-0xfef0bfff,0xe8000000-0xebffffff,0xec200000-0xec2fffff irq 43 on
> ocpbus0
> pci5: <PCI bus> on pcib5
> pcib6: <PCI-PCI bridge> at device 0.0 on pci5
> pci6: <PCI bus> on pcib6
> pci6: <memory> at device 0.0 (no driver attached)
> i2c0: <MPC85XX OnChip i2c controller> iomem 0xfef03000-0xfef03014 irq 59 on
> ocpbus0
> i2c1: <MPC85XX OnChip i2c controller> iomem 0xfef03100-0xfef03114 irq 59 on
> ocpbus0
> Timecounters tick every 10.000 msec
> md0: Preloaded image </isofs-install-ex> 10477568 bytes at 0xa05ffd7c
> da1 at umass-sim1 bus 1 target 0 lun 0
> da1: <Generic STORAGE DEVICE 9407> Removable Direct Access SCSI-0 device
> da1: 40.000MB/s transfers
> da1: 1910MB (3911680 512 byte sectors: 255H 63S/T 243C)
> da0 at umass-sim0 bus 0 target 0 lun 0
> da0: <ST ST72682 2.10> Removable Direct Access SCSI-2 device
> da0: 40.000MB/s transfers
> da0: 1000MB (2048000 512 byte sectors: 64H 32S/T 1000C)
> Trying to mount root from cd9660:/dev/md0
> FILE SYSTEM CLEAN; SKIPPING CHECKS
> clean, 160996 free (28 frags, 20121 blocks, 0.0% fragmentation)
> tunefs: soft updates remains unchanged as disabled
> FILE SYSTEM CLEAN; SKIPPING CHECKS
> clean, 28254 free (38 frags, 3527 blocks, 0.1% fragmentation)
> /dev/da0s2a: 187.2MB (383352 sectors) block size 16384, fragment size 2048
>         using 4 cylinder groups of 46.80MB, 2995 blks, 6016 inodes.
>         with soft updates
> super-block backups (for fsck -b #) at:
> 32, 95872, 191712, 287552
> /dev/da0s2f: 124.8MB (255584 sectors) block size 16384, fragment size 2048
>         using 4 cylinder groups of 31.20MB, 1997 blks, 4096 inodes.
>         with soft updates
> super-block backups (for fsck -b #) at:
> 32, 63936, 127840, 191744
> Installing disk1:/jinstall-ex-4200-10.0R4.7-domestic-signed.tgz
> /dev/da0s3d: 319.6MB (654524 sectors) block size 16384, fragment size 2048
>         using 4 cylinder groups of 79.91MB, 5114 blks, 10240 inodes.
> super-block backups (for fsck -b #) at:
> 32, 163680, 327328, 490976
> tty: not found
> tty: not found
> tty: not found
> tty: not found
> date: connect: Can't assign requested address
> Checking package integrity...
> Verified SHA1 checksum of jbase-ex-10.0R4.7.tgz
> Verified SHA1 checksum of jboot-ex-10.0R4.7.tgz
> Verified SHA1 checksum of jcrypto-ex-10.0R4.7.tgz
> Verified SHA1 checksum of jdocs-ex-10.0R4.7.tgz
> Verified SHA1 checksum of jkernel-ex-10.0R4.7.tgz
> Verified SHA1 checksum of jpfe-ex42x-10.0R4.7.tgz
> Verified SHA1 checksum of jroute-ex-10.0R4.7.tgz
> Verified SHA1 checksum of jswitch-ex-10.0R4.7.tgz
> Verified SHA1 checksum of jweb-ex-10.0R4.7.tgz
> Running requirements check first for jbundle-ex-4200-10.0R4.7-domestic...
> Running pre-install for jbundle-ex-4200-10.0R4.7-domestic...
> Installing jbundle-ex-4200-10.0R4.7-domestic in
> /tmp/pa2398.26/jbundle-ex-4200-10.0R4.7-domestic.x2398...
> Running post-install for jbundle-ex-4200-10.0R4.7-domestic...
> Adding jkernel-ex...
> Adding jcrypto-ex...
> Adding jdocs-ex...
> Adding jswitch-ex...
> Adding jpfe-ex42x...
> Adding jroute-ex...
> Adding jweb-ex...
> Saving home directories
> *** The installer exited with status 2 ***
> *** The installation is unsuccessful!!! ***
> A shell has been started. type exit<cr> to reboot:
>
>
> Is this a bad switch??
>
> Thanks in advance,
>
> Paul
>
>
>
> _______________________________________________
> juniper-nsp mailing list juniper-nsp at puck.nether.net
> https://puck.nether.net/mailman/listinfo/juniper-nsp
>