[j-nsp] Load balancing using Ethernet Aggregate interface ae0

[Doug Hanks]

I'm really not sure what you're asking.

Aggregated link protection is for a 1:1 active/backup scenario and can't have more than two members, and you still need to do this going to a single switch.

Doug

-----Original Message-----
From: medrees [mailto:medrees at isu.net.sa] 
Sent: Friday, March 18, 2011 11:11 PM
To: Doug Hanks; juniper-nsp at puck.nether.net
Subject: RE: [j-nsp] Load balancing using Ethernet Aggregate interface ae0

Already I have one aggregate and connected to two different switches one
primary and one backup

ge-0/0/0 {                                  to SW1
    gigether-options {
        802.3ad {
            ae0;
            primary;
        }
    }
}
ge-0/1/0 {                               to SW2
    gigether-options {
        802.3ad {
            ae0;
            backup;
        }
    }
}

-----Original Message-----
From: Doug Hanks [mailto:dhanks at juniper.net] 
Sent: Saturday, March 19, 2011 8:57 AM
To: medrees; juniper-nsp at puck.nether.net
Subject: RE: [j-nsp] Load balancing using Ethernet Aggregate interface ae0

As stated before, you can't have an aggregate interface going to two
individual switches.

-----Original Message-----
From: medrees [mailto:medrees at isu.net.sa]
Sent: Friday, March 18, 2011 10:36 PM
To: Doug Hanks; juniper-nsp at puck.nether.net
Subject: RE: [j-nsp] Load balancing using Ethernet Aggregate interface ae0

Hi Doug, All

  Since I have 6509 but without VSS I decided to expand my links using the
same existing model which use one primary link connected to switch and
another backup link to another switch both of them in the same Ethernet
aggregate interface ae0.
 so please confirm this new setup to increase the links I will add one more
primary and one backup links and configure in both switches ether channel
ports but still from the juniper side the same ether aggregate interface
will contain FOUR physical interfaces.

Juniper R1 --- ae0 ---- two primary interfaces ------ two interfaces in one
layer-2 ether channel port Po1 ---- Cisco SW1 Juniper R1 --- ae0 ---- two
backup interfaces  ------ two interfaces in one
layer-2 ether channel port Po1 ---- Cisco SW2

-----Original Message-----
From: juniper-nsp-bounces at puck.nether.net
[mailto:juniper-nsp-bounces at puck.nether.net] On Behalf Of medrees
Sent: Wednesday, March 16, 2011 11:02 AM
To: 'Doug Hanks'; juniper-nsp at puck.nether.net
Subject: Re: [j-nsp] Load balancing using Ethernet Aggregate interface ae0

Thanks Doug a lot.

-----Original Message-----
From: Doug Hanks [mailto:dhanks at juniper.net]
Sent: Wednesday, March 16, 2011 9:35 AM
To: medrees; juniper-nsp at puck.nether.net
Subject: RE: [j-nsp] Load balancing using Ethernet Aggregate interface ae0

Is the Cisco switch you're connecting to a 6509 with VSS?  If so, yes you
can do that.  If not, you won't be able to.

-----Original Message-----
From: medrees [mailto:medrees at isu.net.sa]
Sent: Tuesday, March 15, 2011 11:31 PM
To: Doug Hanks; juniper-nsp at puck.nether.net
Subject: RE: [j-nsp] Load balancing using Ethernet Aggregate interface ae0

Hi Doug

   Thanks for your reply, my question is that "is it possible to make
aggregation in two links from juniper side and the other side is connected
to two different Layer-2 Cisco switches for load balance?" currently I'm
connected this setup but one physical interface as primary and the other as
backup inside the ae0.


-----Original Message-----
From: Doug Hanks [mailto:dhanks at juniper.net]
Sent: Wednesday, March 16, 2011 9:17 AM
To: medrees; juniper-nsp at puck.nether.net
Subject: RE: [j-nsp] Load balancing using Ethernet Aggregate interface ae0

If I understand your question correctly ...

LACP requires a single signaling plane, so the remote devices need to be a
virtual-chassis, mc-lag, VSS or some other virtualization technology.

If you use a static LAG, there's no signaling at all, and the above still
applies, as the packets have to be reassembled on the remote device.  If the
remote devices truly are separate, you will just end up black holing the
traffic.  In this case just using a routing protocol.

Doug

-----Original Message-----
From: juniper-nsp-bounces at puck.nether.net
[mailto:juniper-nsp-bounces at puck.nether.net] On Behalf Of medrees
Sent: Tuesday, March 15, 2011 11:06 PM
To: juniper-nsp at puck.nether.net
Subject: [j-nsp] Load balancing using Ethernet Aggregate interface ae0

Hi Expertise

         I'm going to create new Aggregate Ethernet for M10i router to load
balance the traffic among these interfaces and I know that juniper router
can do this aggregation even if the remote side is connected to two
different devices, so in this case I won't deploy LACP and will use the ON
mode , but I'm confused if it will work correctly and what is the operation
mechanism the router use to can force the other side devices to load share
the downstream traffic on aggregated physical interfaces.

So if anyone can help me with documentation or his experience for this task
send to me.

Thanks in advance.


_______________________________________________
juniper-nsp mailing list juniper-nsp at puck.nether.net
https://puck.nether.net/mailman/listinfo/juniper-nsp



_______________________________________________
juniper-nsp mailing list juniper-nsp at puck.nether.net
https://puck.nether.net/mailman/listinfo/juniper-nsp