[j-nsp] SXR 650 Redundancy Group Problem

[Walaa Abdel razzak]

Hi Experts

 

I am configuring redundancy group to trigger failover in case of interface failure. I have reth interface for trust zone that has two physical interfaces, one interface on the active node and the other on the passive and the same for reth1 on untrust zone. The target is to make traffic go through the passive node in case of any physical interface failure in the active node. The problem I am facing is that the failover happen normally when any interface goes down but there is no traffic from trust to untrust or vice versa, when the down interface comes to up again, the traffic flows without problems.

 

The RG configuration is as follows:

 

test at FW1# show chassis                               

cluster {

    reth-count 2;

    redundancy-group 0 {

        node 0 priority 100;

        node 1 priority 1;

    }

    redundancy-group 1 {

        node 0 priority 100;

        node 1 priority 1;

        preempt;

        gratuitous-arp-count 4;

        interface-monitor {

            ge-2/0/0 weight 255;  à Interface on the active node

            ge-2/0/1 weight 255; à Interface on the active node

        }

    }

}

 

When the active interface goes down:

 

Mar 20 03:43:51  FW1 jsrpd[1085]: JSRPD_RG_STATE_CHANGE: Redundancy-group 1 transitioned from 'primary' to 'secondary-hold' state due to Monitor failed: IF 

Mar 20 03:43:52  FW1 jsrpd[1085]: JSRPD_RG_STATE_CHANGE: Redundancy-group 1 transitioned from 'secondary-hold' to 'secondary' state due to Back to back failover interval expired

 

 

Interface belonging to the reth:

 

test@ FW1# show interfaces ge-2/0/0  à active node

gigether-options {

    redundant-parent reth1;

}

 

{primary:node0}[edit]

test@ FW1# show interfaces ge-2/0/1    à active node

gigether-options {

    redundant-parent reth0;

}

 

{primary:node0}[edit]

test@ FW1# show interfaces ge-11/0/0   à passive node

gigether-options {

    redundant-parent reth1;

}

 

{primary:node0}[edit]

test@ FW1# show interfaces ge-11/0/1    à passive node

gigether-options {

    redundant-parent reth0;

}

 

test at FW1# run show interfaces terse | match reth 

ge-2/0/0.15             up    down aenet    --> reth1.15   à active interface down

ge-2/0/0.20             up    down aenet    --> reth1.20

ge-2/0/0.32767          up    down aenet    --> reth1.32767

ge-2/0/1.5              up    up   aenet    --> reth0.5

ge-2/0/1.32767          up    up   aenet    --> reth0.32767

ge-11/0/0.15            up    up   aenet    --> reth1.15

ge-11/0/0.20            up    up   aenet    --> reth1.20

ge-11/0/0.32767         up    up   aenet    --> reth1.32767

ge-11/0/1.5             up    up   aenet    --> reth0.5

ge-11/0/1.32767         up    up   aenet    --> reth0.32767

reth0                   up    down

reth0.5                 up    down inet     172.16.0.2/30   

reth0.32767             up    down

reth1                   up    down

reth1.15                up    down inet     192.168.0.2/30  

reth1.20                up    down inet     192.168.1.2/30  

reth1.32767             up    down

 

Any suggestions?

 

BR,