[j-nsp] Tower top switch/router recommendation..

[Doug Hanks]

I would have to look into it, but you should be able to set a max bandwidth/transmit under cos then use filters + policers per customer.

-----Original Message-----
From: Peter Kranz [mailto:pkranz at unwiredltd.com] 
Sent: Tuesday, March 22, 2011 5:49 PM
To: Doug Hanks; juniper-nsp at puck.nether.net
Subject: RE: [j-nsp] Tower top switch/router recommendation..

Hi Doug,
	Thanks for responding..

I need to be able to do something like this;

Customer BW Pool of 20 Mbps up and down
	Customer A, 5 Mbps committed information rate CIR, burstable to 15
Mbps as long as resources are available
	Customer B, 5 Mbps committed information rate CIR, burstable to 15
Mbps as long as resources are available..

If both customers attempt 15 Mbps at the same time, the switch should give
each 10 Mbps..

Easy to do in HTB using RATE= and CEIL= statements, but I can't figure out
how to do it in JunOS..

Peter Kranz
www.UnwiredLtd.com
Desk: 510-868-1614 x100
Mobile: 510-207-0000
pkranz at unwiredltd.com

-----Original Message-----
From: Doug Hanks [mailto:dhanks at juniper.net] 
Sent: Tuesday, March 22, 2011 5:13 PM
To: Peter Kranz; juniper-nsp at puck.nether.net
Subject: RE: [j-nsp] Tower top switch/router recommendation..

Maybe someone else can chime in, as I'm not an expert with MIR.

Junos policers use the token bucket algorithm and allow you to configure a
bandwidth-limit and burst-size-limit.

You can create firewall filters to match traffic and apply these filters as
coarse or as granular as you need.

Here's an example of a 1m policer:

policer 1m {
    if-exceeding {
        bandwidth-limit 1m;
        burst-size-limit 125k;
    }
    then discard;

Doug

-----Original Message-----
From: Peter Kranz [mailto:pkranz at unwiredltd.com]
Sent: Tuesday, March 22, 2011 4:43 PM
To: Doug Hanks; juniper-nsp at puck.nether.net
Subject: RE: [j-nsp] Tower top switch/router recommendation..

It seems like on the EX platform, I would need each customer in a separate
VLAN for this to work (All customers on one port are on the same VLAN, and
only split by subnets).. Also don't see how one goes about setting up a
MIR.. CIR seems straight forward..

Peter Kranz
www.UnwiredLtd.com
Desk: 510-868-1614 x100
Mobile: 510-207-0000
pkranz at unwiredltd.com



-----Original Message-----
From: Doug Hanks [mailto:dhanks at juniper.net]
Sent: Tuesday, March 22, 2011 4:29 PM
To: Peter Kranz; juniper-nsp at puck.nether.net
Subject: RE: [j-nsp] Tower top switch/router recommendation..

The EX4200-48P - supports virtual-chassis[1] - or the EX3200-48P can do
this, although is requires an advanced license for BGP (EX-48-AFL).

CoS is pretty much the same for all Junos devices.  Take a look at the
technical documentation for the EX and CoS.

http://www.juniper.net/techpubs/en_US/junos10.4/information-products/pathway
-pages/ex-series/cos.html

[1] http://www.juniper.net/us/en/local/pdf/datasheets/1000215-en.pdf

Doug

-----Original Message-----
From: juniper-nsp-bounces at puck.nether.net
[mailto:juniper-nsp-bounces at puck.nether.net] On Behalf Of Peter Kranz
Sent: Tuesday, March 22, 2011 3:20 PM
To: juniper-nsp at puck.nether.net
Subject: [j-nsp] Tower top switch/router recommendation..

I'm wondering if this is something that could be done with Junipers;

On our mountain top sites, we currently have dual 48 port POE switches, and
dual Dell 1950's running Quagga/Zebra routing suites..
The sites support wimax access points and redundant microwave backhauls to
other towers or our data centers..
OSPF/BGP is used to mesh the sites with Quagga/Zebra handling the route
failover..
Each access point (one per port on the switch) can have up to 75 customers
on them, and we use HTB on Linux to apply CIR and MIR rules to each customer
at a subnet level..

Over the years, this solution has proven to be reliable, and surprisingly
high performance, but as traffic volumes to the towers grow with
next-generation products, we are starting to push 400-600 Mbps to the
towers. Additionally, it's a bit of a pain to rebuild failed linux routers
in the field, or replace power supplies, hard drives, etc..

So, I'm looking for some form of stacking router/switch solution that could
handle BGP/OSPF/~75 MIR and CIR rules per interface with enforcement by
customer subnet (they are all on the same interface and vlan)/and tcpdump
for easy debug of customer connectivity problems..

Possible with Juniper? Is so, what device, and what QOS rules? 

Peter Kranz
Founder/CEO - Unwired Ltd
www.UnwiredLtd.com
Desk: 510-868-1614 x100
Mobile: 510-207-0000
pkranz at unwiredltd.com




_______________________________________________
juniper-nsp mailing list juniper-nsp at puck.nether.net
https://puck.nether.net/mailman/listinfo/juniper-nsp