[j-nsp] MX5-error while booting.

[megabitik]

I'd try to use install-media to get everything back to factory defaults. Have you tried this yet?

With best regards,
Vitaly Vlasenko

On 29.11.2012, at 12:04, 叶雨飞 <sunyucong at gmail.com> wrote:

> it says DRAM test fails, my guess is you need to replace memory.
> 
> On Wed, Nov 28, 2012 at 8:57 PM, Ali Sumsam
> <ali+junipernsp at eintellego.net> wrote:
>> Here are some more errors if it helps
>> 
>> 
>> tunefs: soft updates remains unchanged as disabled
>> 
>> Creating initial configuration...Interface control process:
>> /usr/libexec/ld-elf.so.1: Shared object "libcrypto.so.3" not found,
>> required by "cgatool"
>> 
>> umass0: at uhub0 port 3 (addr 2) disconnected
>> 
>> (da0:umass-sim0:0:0:0): lost device
>> 
>> g_vfs_done():da0s1a[WRITE(offset=8192, length=2048)]error = 6
>> 
>> umass0: detached
>> 
>> umass1: at uhub0 port 2 (addr 3) disconnected
>> 
>> (da1:umass-sim1:1:0:0): lost device
>> 
>> g_vfs_done():da1s1f[WRITE(offset=8192, length=2048)]error = 6
>> 
>> mgd: warning: panic: vinvalbuf: dirty bufs
>> 
>> Uptime: 1m29s
>> 
>> (da0:dead_sim0:0:0:0): Synchronize cache failed, status == 0x8, scsi status
>> == 0x0
>> 
>> (da1:dead_sim0:0:0:0): Synchronize cache failed, status == 0x8, scsi status
>> == 0x0
>> 
>> Cannot dump. No dump device defined.
>> 
>> Automatic reboot in 15 seconds - press a key on the console to abort
>> 
>> 
>> *Ali Sumsam CCIE*
>> *Network Engineer - Level 3*
>> eintellego Pty Ltd
>> ali at eintellego.net ; www.eintellego.net
>> 
>> Phone: 1300 753 383 ; Fax: (+612) 8572 9954
>> 
>> Cell +61 (0)410 603 531
>> 
>> facebook.com/eintellego
>> PO Box 7726, Baulkham Hills, NSW 1755 Australia
>> 
>> The Experts Who The Experts Call
>> Juniper - Cisco – Brocade - IBM
>> 
>> 
>> 
>> On Thu, Nov 29, 2012 at 12:21 PM, Ali Sumsam
>> <ali+junipernsp at eintellego.net>wrote:
>> 
>>> Hi,
>>> 
>>> My new MX5 died today. If I try to boot it up, it stuck at following
>>> message.
>>> 
>>> U-Boot 1.1.6 (Jun 10 2011 - 00:50:30)
>>> 
>>> CPU:   8572, Version: 2.1, (0x80e00021)
>>> Core0:  E500, Version: 3.0, (0x80210030)
>>> Clock Configuration:
>>>       CPU0:1333 MHz,        CPU1:1333 MHz, CCB: 533 MHz,
>>>       DDR: 267 MHz (533 MT/s data rate) (Synchronous), LBC:  33 MHz
>>> L1:    D-cache 32 kB enabled
>>>       I-cache 32 kB enabled
>>> Board: MX5-T 1.8
>>> CPLD:  Version 0x1f
>>> DRAM:  Initializing  -     DDR: 2048 MB
>>> Testing DRAM from 0x00000000 to 0x80000000
>>> DRAM test phase 1:
>>> DRAM test fails at: 7ff63e24
>>> hang at function = 0xfffbe504
>>> ### ERROR ### Please RESET the board ###
>>> 
>>> 
>>> Any suggestions?
>>> 
>>> Regards,
>>> 
>>> *Ali Sumsam CCIE*
>>> *Network Engineer - Level 3*
>>> eintellego Pty Ltd
>>> ali at eintellego.net ; www.eintellego.net
>>> 
>>> Phone: 1300 753 383 ; Fax: (+612) 8572 9954
>>> 
>>> Cell +61 (0)410 603 531
>>> 
>>> facebook.com/eintellego
>>> PO Box 7726, Baulkham Hills, NSW 1755 Australia
>>> 
>>> The Experts Who The Experts Call
>>> Juniper - Cisco – Brocade - IBM
>> _______________________________________________
>> juniper-nsp mailing list juniper-nsp at puck.nether.net
>> https://puck.nether.net/mailman/listinfo/juniper-nsp
> 
> _______________________________________________
> juniper-nsp mailing list juniper-nsp at puck.nether.net
> https://puck.nether.net/mailman/listinfo/juniper-nsp