[j-nsp] MX5-error while booting.

[叶雨飞]

it says DRAM test fails, my guess is you need to replace memory.

On Wed, Nov 28, 2012 at 8:57 PM, Ali Sumsam
<ali+junipernsp at eintellego.net> wrote:
> Here are some more errors if it helps
>
>
> tunefs: soft updates remains unchanged as disabled
>
> Creating initial configuration...Interface control process:
> /usr/libexec/ld-elf.so.1: Shared object "libcrypto.so.3" not found,
> required by "cgatool"
>
> umass0: at uhub0 port 3 (addr 2) disconnected
>
> (da0:umass-sim0:0:0:0): lost device
>
> g_vfs_done():da0s1a[WRITE(offset=8192, length=2048)]error = 6
>
> umass0: detached
>
> umass1: at uhub0 port 2 (addr 3) disconnected
>
> (da1:umass-sim1:1:0:0): lost device
>
> g_vfs_done():da1s1f[WRITE(offset=8192, length=2048)]error = 6
>
> mgd: warning: panic: vinvalbuf: dirty bufs
>
> Uptime: 1m29s
>
> (da0:dead_sim0:0:0:0): Synchronize cache failed, status == 0x8, scsi status
> == 0x0
>
> (da1:dead_sim0:0:0:0): Synchronize cache failed, status == 0x8, scsi status
> == 0x0
>
> Cannot dump. No dump device defined.
>
> Automatic reboot in 15 seconds - press a key on the console to abort
>
>
> *Ali Sumsam CCIE*
> *Network Engineer - Level 3*
> eintellego Pty Ltd
> ali at eintellego.net ; www.eintellego.net
>
> Phone: 1300 753 383 ; Fax: (+612) 8572 9954
>
> Cell +61 (0)410 603 531
>
> facebook.com/eintellego
> PO Box 7726, Baulkham Hills, NSW 1755 Australia
>
> The Experts Who The Experts Call
> Juniper - Cisco – Brocade - IBM
>
>
>
> On Thu, Nov 29, 2012 at 12:21 PM, Ali Sumsam
> <ali+junipernsp at eintellego.net>wrote:
>
>> Hi,
>>
>> My new MX5 died today. If I try to boot it up, it stuck at following
>> message.
>>
>> U-Boot 1.1.6 (Jun 10 2011 - 00:50:30)
>>
>> CPU:   8572, Version: 2.1, (0x80e00021)
>> Core0:  E500, Version: 3.0, (0x80210030)
>> Clock Configuration:
>>        CPU0:1333 MHz,        CPU1:1333 MHz, CCB: 533 MHz,
>>        DDR: 267 MHz (533 MT/s data rate) (Synchronous), LBC:  33 MHz
>> L1:    D-cache 32 kB enabled
>>        I-cache 32 kB enabled
>> Board: MX5-T 1.8
>> CPLD:  Version 0x1f
>> DRAM:  Initializing  -     DDR: 2048 MB
>> Testing DRAM from 0x00000000 to 0x80000000
>> DRAM test phase 1:
>> DRAM test fails at: 7ff63e24
>> hang at function = 0xfffbe504
>> ### ERROR ### Please RESET the board ###
>>
>>
>> Any suggestions?
>>
>> Regards,
>>
>> *Ali Sumsam CCIE*
>> *Network Engineer - Level 3*
>> eintellego Pty Ltd
>> ali at eintellego.net ; www.eintellego.net
>>
>> Phone: 1300 753 383 ; Fax: (+612) 8572 9954
>>
>> Cell +61 (0)410 603 531
>>
>> facebook.com/eintellego
>> PO Box 7726, Baulkham Hills, NSW 1755 Australia
>>
>> The Experts Who The Experts Call
>> Juniper - Cisco – Brocade - IBM
>>
>>
> _______________________________________________
> juniper-nsp mailing list juniper-nsp at puck.nether.net
> https://puck.nether.net/mailman/listinfo/juniper-nsp