[j-nsp] MX5-error while booting.

Ali Sumsam ali+junipernsp at eintellego.net
Wed Nov 28 23:57:35 EST 2012


Here are some more errors if it helps


tunefs: soft updates remains unchanged as disabled

Creating initial configuration...Interface control process:
/usr/libexec/ld-elf.so.1: Shared object "libcrypto.so.3" not found,
required by "cgatool"

umass0: at uhub0 port 3 (addr 2) disconnected

(da0:umass-sim0:0:0:0): lost device

g_vfs_done():da0s1a[WRITE(offset=8192, length=2048)]error = 6

umass0: detached

umass1: at uhub0 port 2 (addr 3) disconnected

(da1:umass-sim1:1:0:0): lost device

g_vfs_done():da1s1f[WRITE(offset=8192, length=2048)]error = 6

mgd: warning: panic: vinvalbuf: dirty bufs

Uptime: 1m29s

(da0:dead_sim0:0:0:0): Synchronize cache failed, status == 0x8, scsi status
== 0x0

(da1:dead_sim0:0:0:0): Synchronize cache failed, status == 0x8, scsi status
== 0x0

Cannot dump. No dump device defined.

Automatic reboot in 15 seconds - press a key on the console to abort


*Ali Sumsam CCIE*
*Network Engineer - Level 3*
eintellego Pty Ltd
ali at eintellego.net ; www.eintellego.net

Phone: 1300 753 383 ; Fax: (+612) 8572 9954

Cell +61 (0)410 603 531

facebook.com/eintellego
PO Box 7726, Baulkham Hills, NSW 1755 Australia

The Experts Who The Experts Call
Juniper - Cisco – Brocade - IBM



On Thu, Nov 29, 2012 at 12:21 PM, Ali Sumsam
<ali+junipernsp at eintellego.net>wrote:

> Hi,
>
> My new MX5 died today. If I try to boot it up, it stuck at following
> message.
>
> U-Boot 1.1.6 (Jun 10 2011 - 00:50:30)
>
> CPU:   8572, Version: 2.1, (0x80e00021)
> Core0:  E500, Version: 3.0, (0x80210030)
> Clock Configuration:
>        CPU0:1333 MHz,        CPU1:1333 MHz, CCB: 533 MHz,
>        DDR: 267 MHz (533 MT/s data rate) (Synchronous), LBC:  33 MHz
> L1:    D-cache 32 kB enabled
>        I-cache 32 kB enabled
> Board: MX5-T 1.8
> CPLD:  Version 0x1f
> DRAM:  Initializing  -     DDR: 2048 MB
> Testing DRAM from 0x00000000 to 0x80000000
> DRAM test phase 1:
> DRAM test fails at: 7ff63e24
> hang at function = 0xfffbe504
> ### ERROR ### Please RESET the board ###
>
>
> Any suggestions?
>
> Regards,
>
> *Ali Sumsam CCIE*
> *Network Engineer - Level 3*
> eintellego Pty Ltd
> ali at eintellego.net ; www.eintellego.net
>
> Phone: 1300 753 383 ; Fax: (+612) 8572 9954
>
> Cell +61 (0)410 603 531
>
> facebook.com/eintellego
> PO Box 7726, Baulkham Hills, NSW 1755 Australia
>
> The Experts Who The Experts Call
> Juniper - Cisco – Brocade - IBM
>
>


More information about the juniper-nsp mailing list