[j-nsp] l2circuit/xconnect between MX104 and a ME3600X
Caio
caiot5 at gmail.com
Fri Sep 30 10:26:30 EDT 2016
I'm sorry, the interface was down at the time I was extracting the outputs
you requested, here's the output with the interface being up:
#show xconnect interface Gi0/1 detail
Legend: XC ST=Xconnect State S1=Segment1 State S2=Segment2 State
UP=Up DN=Down AD=Admin Down IA=Inactive
SB=Standby HS=Hot Standby RV=Recovering NH=No Hardware
XC ST Segment 1 S1 Segment 2
S2
------+---------------------------------+--+---------------------------------+--
DN pri ac Gi0/1:55(Ethernet) UP mpls YY.YY.YY.YY:2
DN
Interworking: none Local VC label 16
Remote VC label 300192
pw-class: eompls
#show xconnect interface Gi0/1 detail
Legend: XC ST=Xconnect State S1=Segment1 State S2=Segment2 State
UP=Up DN=Down AD=Admin Down IA=Inactive
SB=Standby HS=Hot Standby RV=Recovering NH=No Hardware
XC ST Segment 1 S1 Segment 2
S2
------+---------------------------------+--+---------------------------------+--
DN pri ac Gi0/1:55(Ethernet) UP mpls YY.YY.YY.YY:2
DN
Interworking: none Local VC label 16
Remote VC label 300192
pw-class: eompls
#show mpls l2transport vc 2 detail
Local interface: Gi0/1 up, line protocol up, Ethernet up
Destination address: YY.YY.YY.YY, VC ID: 2, VC status: down
Last error: MPLS dataplane reported a fault to the nexthop
Output interface: none, imposed label stack {}
Preferred path: not configured
Default path: no route
No adjacency
Create time: 00:12:03, last status change time: 00:05:07
Last label FSM state change time: 00:05:07
Signaling protocol: LDP, peer YY.YY.YY.YY:0 up
Targeted Hello: XX.XX.XX.XX(LDP Id) -> YY.YY.YY.YY, LDP is UP
Graceful restart: not configured and not enabled
Non stop routing: configured and not enabled
Status TLV support (local/remote) : enabled/not supported
LDP route watch : enabled
Label/status state machine : activating, LruRruD
Last local dataplane status rcvd: DOWN(pw-tx-fault)
Last BFD dataplane status rcvd: Not sent
Last BFD peer monitor status rcvd: No fault
Last local AC circuit status rcvd: No fault
Last local AC circuit status sent: DOWN(pw-rx-fault)
Last local PW i/f circ status rcvd: No fault
Last local LDP TLV status sent: No fault
Last remote LDP TLV status rcvd: Not sent
Last remote LDP ADJ status rcvd: No fault
MPLS VC labels: local 16, remote 300192
Group ID: local 0, remote 0
MTU: local 1600, remote 1600
Remote interface description:
Sequencing: receive disabled, send disabled
Control Word: Off
Dataplane:
SSM segment/switch IDs: 0/4096 (used), PWID: 1
VC statistics:
transit packet totals: receive 0, send 0
transit byte totals: receive 0, send 0
transit packet drops: receive 0, seq error 0, send 0
#show mpls l2transport binding 2
Destination Address: YY.YY.YY.YY,VC ID: 2
Local Label: 16
Cbit: 0, VC Type: Ethernet, GroupID: 0
MTU: 1600, Interface Desc: NOBLE L2L SPO
VCCV: CC Type: CW [1], RA [2]
CV Type: LSPV [2], BFD/Raw [5]
Remote Label: 300192
Cbit: 0, VC Type: Ethernet, GroupID: 0
MTU: 1600, Interface Desc: n/a
VCCV: CC Type: RA [2], TTL [3]
CV Type: LSPV [2], BFD/UDP [3]
#show mpls forwarding-table labels 18 detail
Local Outgoing Prefix Bytes Label Outgoing Next Hop
Label Label or Tunnel Id Switched interface
On Fri, Sep 30, 2016 at 11:06 AM, Caio <caiot5 at gmail.com> wrote:
> Hi James,
>
> Here's the configuration:
> Juniper side:
>
> set interfaces ge-0/0/0 mtu 1600
> set interfaces ge-0/0/0 encapsulation ethernet-ccc
> set interfaces ge-0/0/0 unit 0
> set protocols l2circuit neighbor XX.XX.XX.XX interface ge-0/0/0.0
> virtual-circuit-id 2
> set protocols l2circuit neighbor XX.XX.XX.XX interface ge-0/0/0.0
> control-word
> set protocols l2circuit neighbor XX.XX.XX.XX interface ge-0/0/0.0 mtu 1600
> set protocols l2circuit neighbor XX.XX.XX.XX interface ge-0/0/0.0
> pseudowire-status-tlv
> set protocols ldp interface xe-2/0/1.1 transport-address router-id
> set protocols mpls interface xe-2/0/1.1
> set protocols ldp egress-policy connected
> set protocols ldp deaggregate
> set protocols ldp interface lo0.0 transport-address interface
> set interfaces lo0 unit 0 family inet address YY.YY.YY.YY/32
>
>
> Cisco side:
>
> pseudowire-class eompls
> encapsulation mpls
> control-word
>
> interface GigabitEthernet0/1
> no switchport
> mtu 1600
> no ip address
> xconnect YY.YY.YY.YY 2 encapsulation mpls pw-class eompls
>
>
> mpls ldp router-id Loopback0 force
>
> interface Loopback0
> ip address XX.XX.XX.XX 255.255.255.255
>
> And here's the output you requested from the cisco device:
>
> #show xconnect interface Gi0/1 detail
> Legend: XC ST=Xconnect State S1=Segment1 State S2=Segment2 State
> UP=Up DN=Down AD=Admin Down IA=Inactive
> SB=Standby HS=Hot Standby RV=Recovering NH=No Hardware
>
> XC ST Segment 1 S1 Segment 2
> S2
> ------+---------------------------------+--+----------------
> -----------------+--
> AD pri ac Gi0/1:55(Ethernet) AD mpls YY.YY.YY.YY:2
> DN
> Interworking: none Local VC label unassigned
>
> Remote VC label 300192
>
> pw-class: eompls
>
> #show mpls l2transport vc 2 detail
> Local interface: Gi0/1 admin down, line protocol down, Ethernet admin down
> Destination address: YY.YY.YY.YY, VC ID: 2, VC status: admin down
> Last error: Local access circuit is not ready for label advertise
> Output interface: none, imposed label stack {}
> Preferred path: not configured
> Default path: no route
> No adjacency
> Create time: 01:07:10, last status change time: 00:38:27
> Last label FSM state change time: 00:35:04
> Signaling protocol: LDP, peer YY.YY.YY.YY:0 up
> Targeted Hello: XX.XX.XX.XX(LDP Id) -> YY.YY.YY.YY, LDP is UP
> Graceful restart: not configured and not enabled
> Non stop routing: configured and not enabled
> Status TLV support (local/remote) : enabled/not supported
> LDP route watch : enabled
> Label/status state machine : remote ready, LndRru
> Last local dataplane status rcvd: No fault
> Last BFD dataplane status rcvd: Not sent
> Last BFD peer monitor status rcvd: No fault
> Last local AC circuit status rcvd: DOWN(hard-down)
> Last local AC circuit status sent: No fault
> Last local PW i/f circ status rcvd: No fault
> Last local LDP TLV status sent: DOWN AC(rx/tx faults),
> (pw-tx-fault) (withdrawn)
> Last remote LDP TLV status rcvd: Not sent
> Last remote LDP ADJ status rcvd: No fault
> MPLS VC labels: local unassigned, remote 300192
> Group ID: local unknown, remote 0
> MTU: local unknown, remote 1600
> Remote interface description:
> Sequencing: receive disabled, send disabled
> Control Word: Off
> Dataplane:
> SSM segment/switch IDs: 0/8124 (used), PWID: 1
> VC statistics:
> transit packet totals: receive 0, send 0
> transit byte totals: receive 0, send 0
> transit packet drops: receive 0, seq error 0, send 0
>
>
> #show mpls l2transport binding 2
> Destination Address: YY.YY.YY.YY,VC ID: 2
> Local Label: unassigned.
> Remote Label: 300192
> Cbit: 0, VC Type: Ethernet, GroupID: 0
> MTU: 1600, Interface Desc: n/a
> VCCV: CC Type: RA [2], TTL [3]
> CV Type: LSPV [2], BFD/UDP [3]
>
> #show mpls forwarding-table labels 18 detail
> Local Outgoing Prefix Bytes Label Outgoing Next Hop
>
> Label Label or Tunnel Id Switched interface
>
>
> On Fri, Sep 30, 2016 at 5:20 AM, James Bensley <jwbensley at gmail.com>
> wrote:
>
>> You need to share the configs I think you want much help with this.
>>
>> Also from the Cisco side can you give the full output from...
>>
>> show xconnect interface Gi0/1 detail
>>
>> show mpls l2transport vc 2 detail
>>
>> show mpls l2transport binding 2
>>
>> show mpls forwarding-table labels 18 detail
>>
>>
>> Cheers,
>> James.
>> _______________________________________________
>> juniper-nsp mailing list juniper-nsp at puck.nether.net
>> https://puck.nether.net/mailman/listinfo/juniper-nsp
>>
>
>
More information about the juniper-nsp
mailing list