[j-nsp] MX240+QFX5100 using Fusion - Any positive experience
Alain Hebert
ahebert at pubnix.net
Thu Aug 10 15:32:11 EDT 2017
Yeah,
We have 104's too but since they're in production, its not a good
idea to even sneeze nearthem =D.
So we're using one of our future productionMX240 with "MPCE Type 3
3D" with a "10X10GE SFP+" MIC. Pretty much the generic one for MX240
The cascade ports works enough to talk to the satellite and
convert/upgrade/downgrade them. Had no issue testing with xe-2/0/3-9
with generic stuff.
Thanks for the input.
> show chassis hardware
Hardware inventory:
Item Version Part number Description
Chassis MX240
Midplane REV 07 760-021404 MX240 Backplane
FPM Board REV 03 760-021392 Front Panel Display
PEM 0 Rev 10 740-029970 PS 1.4-2.52kW; 90-264VAC in
PEM 1 Rev 06 740-029970 PS 1.4-2.52kW; 90-264VAC in
PEM 2 Rev 05 740-029970 PS 1.4-2.52kW; 90-264VAC in
PEM 3 Rev 07 740-029970 PS 1.4-2.52kW; 90-264VAC in
Routing Engine 0 REV 08 740-031116 RE-S-1800x4
Routing Engine 1 REV 08 740-031116 RE-S-1800x4
CB 0 REV 14 750-031391 Enhanced MX SCB
CB 1 REV 14 750-031391 Enhanced MX SCB
FPC 2 REV 07 750-045372 MPCE Type 3 3D
CPU REV 08 711-035209 HMPC PMB 2G
MIC 0 REV 07 750-033307 10X10GE SFPP
PIC 0 BUILTIN 10X10GE SFPP
Xcvr 0 REV 01 740-031980 SFP+-10G-SR
Xcvr 1 REV 01 740-021308 SFP+-10G-SR
Fan Tray 0 REV 01 710-030216 Enhanced Fan Tray
set chassis redundancy routing-engine 0 master
set chassis redundancy routing-engine 1 backup
set chassis network-services enhanced-ip
set chassis satellite-management fpc 101 serial-number <snip>
set chassis satellite-management fpc 101 SAT1
set chassis satellite-management fpc 101 cascade-ports xe-2/0/1
set chassis satellite-management fpc 102 serial-number <snip>
set chassis satellite-management fpc 102 SAT2
set chassis satellite-management fpc 102 cascade-ports xe-2/0/0
set chassis satellite-management upgrade-groups GROUP1 satellite 101
set chassis satellite-management upgrade-groups GROUP2 satellite 102
set chassis satellite-management auto-satellite-conversion satellite 101
set chassis satellite-management auto-satellite-conversion satellite 102
> show chassis satellite
Device Cascade Port Extended Ports
Alias Slot State Ports State Total/Up
SAT1 101 Online xe-2/0/1 online 4/4
SAT2 102 Online xe-2/0/0 online 7/6
This is a Copper/SFP, same source SFP as those that are currently
working in your QFX5100, but with Junos.
> show interfaces ge-102/0/20
Physical interface: ge-102/0/20, Enabled, Physical link is Up, Extended Port
Interface index: 157, SNMP ifIndex: 546
Description: <snip>
Link-level type: Ethernet, MTU: 1500, MRU: 1508, LAN-PHY mode,
Link-mode: *Half-duplex,* Speed: Auto, BPDU Error: None,
Loop Detect PDU Error: None, Ethernet-Switching Error: None,
MAC-REWRITE Error: None, Loopback: Disabled, Source filtering: Disabled,
Flow control: Enabled, Auto-negotiation: Enabled, Remote fault: Online,
IEEE 802.3az Energy Efficient Ethernet: Disabled, Auto-MDIX: Enabled
Pad to minimum frame size: Disabled
Device flags : Present Running
Interface flags: SNMP-Traps Internal: 0x4000
Link flags : None
CoS queues : 8 supported, 8 maximum usable queues
Schedulers : 0
Current address: f4:b5:2f:44:48:04, Hardware address: f4:b5:2f:44:48:04
Last flapped : 2017-08-10 08:03:30 EDT (07:11:46 ago)
Input rate : 464 bps (1 pps)
Output rate : 0 bps (0 pps)
Active alarms : None
Active defects : None
Interface transmit statistics: Disabled
Logical interface ge-102/0/20.0 (Index 348) (SNMP ifIndex 552)
Flags: Up 0x4004000 Encapsulation: ENET2
Input packets : 0
Output packets: 100
Protocol inet, MTU: 1486
Max nh cache: 75000, New hold nh limit: 75000, Curr nh cnt: 0,
Curr new hold cnt: 0, NH drop cnt: 0
Flags: Sendbcast-pkt-to-re
Addresses, Flags: Is-Preferred Is-Primary
Destination: 10.25.1.12/31, Local: 10.25.1.13
Protocol multiservice, MTU: Unlimited
Flags: Is-Primary
That bold should be 10Gbps/Full, they're the same source SFP+ as
the cascade ports
> show interfaces xe-102/0/22
Physical interface: xe-102/0/22, Enabled, Physical link is Up, Extended Port
Interface index: 161, SNMP ifIndex: 550
Link-level type: Ethernet, MTU: 1514, MRU: 1522, LAN-PHY mode, Speed:
*Unspecified*, Duplex: *Unspecified*, BPDU Error: None, Loop Detect PDU
Error: None, Ethernet-Switching Error: None, MAC-REWRITE Error: None,
Loopback: Disabled, Source filtering: Disabled, Flow control: Enabled
Pad to minimum frame size: Disabled
Device flags : Present Running
Interface flags: SNMP-Traps Internal: 0x4000
Link flags : None
CoS queues : 8 supported, 8 maximum usable queues
Schedulers : 0
Current address: f4:b5:2f:44:48:04, Hardware address: f4:b5:2f:44:48:04
Last flapped : 2017-08-10 08:03:30 EDT (07:23:44 ago)
Input rate : 0 bps (0 pps)
Output rate : 0 bps (0 pps)
Active alarms : None
Active defects : None
Interface transmit statistics: Disabled
Logical interface xe-102/0/22.0 (Index 351) (SNMP ifIndex 555)
Flags: Up SNMP-Traps 0x4004000 Encapsulation: ENET2
Input packets : 0
Output packets: 85
Protocol inet, MTU: 1500
Max nh cache: 75000, New hold nh limit: 75000, Curr nh cnt: 0, Curr
new hold cnt: 0, NH drop cnt: 0
Flags: Sendbcast-pkt-to-re, Is-Primary
Addresses, Flags: Is-Default Is-Preferred Is-Primary
Destination: 9.9.9/24, Local: 9.9.9.9, Broadcast: 9.9.9.255
Protocol multiservice, MTU: Unlimited
-----
Alain Hebert ahebert at pubnix.net
PubNIX Inc.
50 boul. St-Charles
P.O. Box 26770 Beaconsfield, Quebec H9W 6G7
Tel: 514-990-5911 http://www.pubnix.net Fax: 514-990-9443
On 08/10/17 14:34, santiago martinez wrote:
> Hi there, which MPC are you using. We have fusion edge on our lab with mx104 and no problem so far.
>
> We have a mx240 , if we have the same MPC I guess I can give it a try.
>
> Can you share your chassis config / show chassis satellite output / show interface ge-102/0/20
>
> Santi
>
>
>
> Sent from my iPhone
>
>> On 10 Aug 2017, at 13:08, Alain Hebert <ahebert at pubnix.net> wrote:
>>
>> Hi,
>>
>> I'm thinking our local Juniper vendor is taking us for his personal Q&A...
>>
>> Another tech sold to us instead of VCF: Fusion.
>>
>> Anyone got it working on MX240+QFX5100...
>>
>>
>> Config:
>>
>> < basic satellite config >
>>
>> set interfaces ge-102/0/20 unit 0 family inet address 10.25.1.13/31
>>
>>
>> Test:
>>
>> Every time I try to ping .12, I get this log.
>>
>> Aug 10 07:49:56 <snip> fpc2 KERNEL/PFE APP=NH OUT OF SYNC: error code 3 REASON: NH add received for an ifl that does not exist ERROR-SPECIFIC INFO: nh_id=684 , type = Hold, ifl index 348 does not exist TYPE-SPECIFIC INFO: none
>>
>>
>> What we looked at:
>>
>> 1. Yes everything was rebooted;
>>
>> 2. Yes The satellite look fine;
>>
>> 3. Yes the latest firmware is on the MX and the QFX;
>>
>> MX: junos-install-mx-x86-32-17.2R1.13.tgz
>>
>> QFX: satellite-3.1R1.3-signed.tgz since satellite-3.1R1.4.tgz is not signed so it cannot be installed.
>>
>> 4. Yes the optic are the same that those working in our QFX Junos native;
>>
>> And no amount of GoogleFu could find a solution. Our next step is JTAC.
>>
>> --
>> -----
>> Alain Hebert ahebert at pubnix.net
>> PubNIX Inc.
>> 50 boul. St-Charles
>> P.O. Box 26770 Beaconsfield, Quebec H9W 6G7
>> Tel: 514-990-5911 http://www.pubnix.net Fax: 514-990-9443
>>
>> _______________________________________________
>> juniper-nsp mailing list juniper-nsp at puck.nether.net
>> https://puck.nether.net/mailman/listinfo/juniper-nsp
More information about the juniper-nsp
mailing list