[j-nsp] MX204 Tunnel Services

Fraser McGlinn fraser at frizianz.com
Thu Dec 27 17:40:45 EST 2018


Further to this, and to clarify I do already have tunnel-services enabled and after configuring I get output packets on each unit, but no input packets. It seems like the PFE is just eating the packets.

fraser@> show configuration chassis | display set | match tunnel-services   
set chassis fpc 0 pic 0 tunnel-services bandwidth 10g
set chassis fpc 0 pic 1 tunnel-services bandwidth 1g

fraser@> show interfaces lt-0/0/0                                            
Physical interface: lt-0/0/0, Enabled, Physical link is Up
  Interface index: 159, SNMP ifIndex: 544
  Type: Logical-tunnel, Link-level type: Logical-tunnel, MTU: Unlimited, Speed: 10000mbps
  Device flags   : Present Running
  Interface flags: Point-To-Point SNMP-Traps Internal: 0x4000
  Link flags     : None
  Physical info  : 13
  Current address: ee:38:73:e9:50:37, Hardware address: ee:38:73:e9:50:37
  Last flapped   : 2018-12-19 03:07:15 AEDT (1w2d 06:20 ago)
  Input rate     : 0 bps (0 pps)
  Output rate    : 0 bps (0 pps)

fraser@> show interfaces lt-0/1/10   
Physical interface: lt-0/1/10, Enabled, Physical link is Up
  Interface index: 160, SNMP ifIndex: 598
  Type: Logical-tunnel, Link-level type: Logical-tunnel, MTU: Unlimited, Speed: 1000mbps
  Device flags   : Present Running
  Interface flags: Point-To-Point SNMP-Traps Internal: 0x4000
  Link flags     : None
  Physical info  : 13
  Current address: ee:38:73:e9:58:27, Hardware address: ee:38:73:e9:58:27
  Last flapped   : 2018-12-19 03:07:15 AEDT (1w2d 06:20 ago)
  Input rate     : 0 bps (0 pps)
  Output rate    : 0 bps (0 pps)

fraser@> show configuration | display set | match lt-0/0/0 
set interfaces lt-0/0/0 unit 100 encapsulation ethernet
set interfaces lt-0/0/0 unit 100 peer-unit 101
set interfaces lt-0/0/0 unit 100 family inet address 100.64.0.1/30
set interfaces lt-0/0/0 unit 101 encapsulation ethernet
set interfaces lt-0/0/0 unit 101 peer-unit 100
set interfaces lt-0/0/0 unit 101 family inet address 100.64.0.2/30
set routing-instances TEST interface lt-0/0/0.101

fraser@> show interfaces lt-0/0/0                 
Physical interface: lt-0/0/0, Enabled, Physical link is Up
  Interface index: 159, SNMP ifIndex: 544
  Type: Logical-tunnel, Link-level type: Logical-tunnel, MTU: Unlimited, Speed: 10000mbps
  Device flags   : Present Running
  Interface flags: Point-To-Point SNMP-Traps Internal: 0x4000
  Link flags     : None
  Physical info  : 13
  Current address: ee:38:73:e9:50:37, Hardware address: ee:38:73:e9:50:37
  Last flapped   : 2018-12-19 03:07:15 AEDT (1w2d 06:29 ago)
  Input rate     : 0 bps (0 pps)
  Output rate    : 0 bps (0 pps)

  Logical interface lt-0/0/0.100 (Index 328) (SNMP ifIndex 588)
    Flags: Up SNMP-Traps 0x4000 Encapsulation: ENET2
    MAC: ee:38:73:e9:50:37
    Input packets : 0
    Output packets: 21
    Protocol inet, MTU: 1500
    Max nh cache: 0, New hold nh limit: 0, Curr nh cnt: 0, Curr new hold cnt: 0, NH drop cnt: 0
      Flags: Sendbcast-pkt-to-re
      Addresses, Flags: Is-Preferred Is-Primary
        Destination: 100.64.0.0/30, Local: 100.64.0.1, Broadcast: 100.64.0.3

  Logical interface lt-0/0/0.101 (Index 333) (SNMP ifIndex 590)
    Flags: Up SNMP-Traps 0x4000 Encapsulation: ENET2
    MAC: ee:38:73:e9:50:38
    Input packets : 0
    Output packets: 10
    Protocol inet, MTU: 1500
    Max nh cache: 0, New hold nh limit: 0, Curr nh cnt: 0, Curr new hold cnt: 0, NH drop cnt: 0
      Flags: Sendbcast-pkt-to-re, Is-Primary
      Addresses, Flags: Is-Default Is-Preferred Is-Primary
        Destination: 100.64.0.0/30, Local: 100.64.0.2, Broadcast: 100.64.0.3

  Logical interface lt-0/0/0.32767 (Index 329) (SNMP ifIndex 589)
    Flags: Up SNMP-Traps 0x4000 VLAN-Tag [ 0x0000.0 ]  Encapsulation: ENET2
    Input packets : 0
    Output packets: 0

fraser@> 

> On 28 Dec 2018, at 2:03 am, Tim Jackson <jackson.tim at gmail.com> wrote:
> 
> I've done LT interfaces on MX204 with multiple LSYS' to build some lab topologies without issue. This was back in beta and worked fine, haven't run it on newer code, but I do run GRE tunnels in 18.1R3 without issue.
> 
> --
> Tim
> 
> 
> 
> On Wed, Dec 26, 2018, 5:43 PM Fraser McGlinn <fraser at frizianz.com <mailto:fraser at frizianz.com> wrote:
> Hey Everyone,
> 
> Yet another post re MX204 ;)
> 
> Trying to get lt-x/x/x interfaces working on MX204 (18.3R1.9), thus far no luck. Interfaces are created and bandwidth set after enabling tunnel services on the PIC, however only output packets on the source interface increment. Input packets do not increment on the receiving unit, so seems to get lost in the nether.
> 
> Has anyone got LT interfaces working on MX204 and an example config?
> 
> Cheers,
> Fraser
> _______________________________________________
> juniper-nsp mailing list juniper-nsp at puck.nether.net <mailto:juniper-nsp at puck.nether.net>
> https://puck.nether.net/mailman/listinfo/juniper-nsp <https://puck.nether.net/mailman/listinfo/juniper-nsp>



More information about the juniper-nsp mailing list