[j-nsp] SRX100 u-boot

[Mohammad Khalil]

Ops , but it did not work either
Nand format failed

BR,
Mohammad

On Sun, 11 Nov 2018 at 14:46, Jonas Frey <jf at probe-networks.de> wrote:

> Hi Mohammad,
>
> thats a typo, its nand_format (note the underscore).
> Am Sonntag, den 11.11.2018, 05:31 -0500 schrieb Mohammad Khalil:
> > => reset
> >
> >
> > U-Boot 1.1.6-JNPR-2.7 (Build time: Nov 26 2013 - 19:04:49)
> >
> > Initializing memory this may take some time...
> > Measured DDR clock 266.62 MHz
> > SRX_100H2 board revision major:1, minor:0, serial #: BZ4214AF1453
> > OCTEON CN5020-SCP pass 1.1, Core clock: 500 MHz, DDR clock: 266 MHz
> > (532
> > Mhz data rate)
> > DRAM:  2048 MB
> > Starting Memory POST...
> > Checking datalines... OK
> > Checking address lines... OK
> > Checking 512K memory for U-Boot... OK.
> > Running U-Boot CRC Test... OK.
> > Flash:  4 MB
> > USB:   scanning bus for devices... 4 USB Device(s) found
> >        scanning bus for storage devices... Read Error for
> > STMicroelectronics device 0
> > Not intializing this device, disabling autoboot
> > Device may need formatting, please issue command :
> >         <nand_format> at console prompt to format
> > 2 Storage Device(s) found
> > Clearing DRAM........ done
> > BIST check passed.
> > Boot Media: nand-flash usb
> > Net:   pic init done (err = 0)octeth0
> > POST Passed
> > Press SPACE to abort autoboot in 1 seconds
> > => nand-format
> > Unknown command 'nand-format' - try 'help'
> >
> >
> > On Sun, 11 Nov 2018 at 04:17, Muhammad Atif Jauhar <atif.jauhar at gmail
> > .com>
> > wrote:
> >
> > >
> > > Hi Khalil,
> > >
> > > Kindly follow below link to recover it.
> > >
> > >
> > > https://forums.juniper.net/t5/SRX-Services-Gateway/Boot-problem-of-
> > > UBoot-srx240-having-status-LED-red/td-p/211103
> > >
> > > Regards,
> > >
> > > Muhammad Atif Jauhar
> > > (+966-56-00-04-985)
> > >
> > >
> > > On Sun, Nov 11, 2018 at 11:36 AM Mohammad Khalil <eng.mssk at gmail.co
> > > m>
> > > wrote:
> > >
> > > >
> > > > Hello all
> > > > I have my Juniper SRX 100h stuck in the u-boot mode
> > > > I have tried to download a new image on a USB stick , plugged it
> > > > into the
> > > > device and tried to upgrade with no luck
> > > > Looked around but could not find a solution , anyone can help
> > > > please?
> > > >
> > > > BR,
> > > > Mohammad
> > > > _______________________________________________
> > > > juniper-nsp mailing list juniper-nsp at puck.nether.net
> > > > https://puck.nether.net/mailman/listinfo/juniper-nsp
> > > >
> > _______________________________________________
> > juniper-nsp mailing list juniper-nsp at puck.nether.net
> > https://puck.nether.net/mailman/listinfo/juniper-nsp
>