[j-nsp] SRX100 u-boot

[Mohammad Khalil]

I cannot see : "loading /boot/defaults/loader.conf" when I reset the device

BR,
Mohammad

On Sun, 11 Nov 2018 at 14:43, Mohammad Khalil <eng.mssk at gmail.com> wrote:

> Ops , but it did not work either
> Nand format failed
>
> BR,
> Mohammad
>
> On Sun, 11 Nov 2018 at 14:46, Jonas Frey <jf at probe-networks.de> wrote:
>
>> Hi Mohammad,
>>
>> thats a typo, its nand_format (note the underscore).
>> Am Sonntag, den 11.11.2018, 05:31 -0500 schrieb Mohammad Khalil:
>> > => reset
>> >
>> >
>> > U-Boot 1.1.6-JNPR-2.7 (Build time: Nov 26 2013 - 19:04:49)
>> >
>> > Initializing memory this may take some time...
>> > Measured DDR clock 266.62 MHz
>> > SRX_100H2 board revision major:1, minor:0, serial #: BZ4214AF1453
>> > OCTEON CN5020-SCP pass 1.1, Core clock: 500 MHz, DDR clock: 266 MHz
>> > (532
>> > Mhz data rate)
>> > DRAM:  2048 MB
>> > Starting Memory POST...
>> > Checking datalines... OK
>> > Checking address lines... OK
>> > Checking 512K memory for U-Boot... OK.
>> > Running U-Boot CRC Test... OK.
>> > Flash:  4 MB
>> > USB:   scanning bus for devices... 4 USB Device(s) found
>> >        scanning bus for storage devices... Read Error for
>> > STMicroelectronics device 0
>> > Not intializing this device, disabling autoboot
>> > Device may need formatting, please issue command :
>> >         <nand_format> at console prompt to format
>> > 2 Storage Device(s) found
>> > Clearing DRAM........ done
>> > BIST check passed.
>> > Boot Media: nand-flash usb
>> > Net:   pic init done (err = 0)octeth0
>> > POST Passed
>> > Press SPACE to abort autoboot in 1 seconds
>> > => nand-format
>> > Unknown command 'nand-format' - try 'help'
>> >
>> >
>> > On Sun, 11 Nov 2018 at 04:17, Muhammad Atif Jauhar <atif.jauhar at gmail
>> > .com>
>> > wrote:
>> >
>> > >
>> > > Hi Khalil,
>> > >
>> > > Kindly follow below link to recover it.
>> > >
>> > >
>> > > https://forums.juniper.net/t5/SRX-Services-Gateway/Boot-problem-of-
>> > > UBoot-srx240-having-status-LED-red/td-p/211103
>> > >
>> > > Regards,
>> > >
>> > > Muhammad Atif Jauhar
>> > > (+966-56-00-04-985)
>> > >
>> > >
>> > > On Sun, Nov 11, 2018 at 11:36 AM Mohammad Khalil <eng.mssk at gmail.co
>> > > m>
>> > > wrote:
>> > >
>> > > >
>> > > > Hello all
>> > > > I have my Juniper SRX 100h stuck in the u-boot mode
>> > > > I have tried to download a new image on a USB stick , plugged it
>> > > > into the
>> > > > device and tried to upgrade with no luck
>> > > > Looked around but could not find a solution , anyone can help
>> > > > please?
>> > > >
>> > > > BR,
>> > > > Mohammad
>> > > > _______________________________________________
>> > > > juniper-nsp mailing list juniper-nsp at puck.nether.net
>> > > > https://puck.nether.net/mailman/listinfo/juniper-nsp
>> > > >
>> > _______________________________________________
>> > juniper-nsp mailing list juniper-nsp at puck.nether.net
>> > https://puck.nether.net/mailman/listinfo/juniper-nsp
>>
>