[j-nsp] SRX100 u-boot

[Mohammad Khalil]

Thanks mate for the help
Actually , am stuck at the => and cannot reach the loader
I hit boot and nothing happened
setenv loaderdev net (without = because it gave me bad character)
reset
and again stuck in =>

On Sun, 11 Nov 2018 at 07:59, Jonas Frey <jf at probe-networks.de> wrote:

> Are you stuck at the "=>" Uboot prompt or are able to reach loader>?
> From loader> it should be pretty straight forward to reinstall junos
> from a install media.
>
> If you are stuck at "=>" then try:
> boot
> (should put you into loader>)
>
> Or:
> setenv loaderdev=net
> reboot
> (this should try to load via net, however it can take some time untill
> it works - just be patient)
>
> Or:
> setenv loaderdev usb1:0
> boot
> (should force to load from usb1)
>
>
> If you have a 2nd (same) SRX you could also try to do a "snapshort
> media usb factory" to the USB stick and afterwards insert that stick
> into the faulty SRX and force it to boot from there.
>
>
>
> Am Sonntag, den 11.11.2018, 14:43 +0200 schrieb Mohammad Khalil:
> > Ops , but it did not work either
> > Nand format failed
> >
> > BR,
> > Mohammad
> >
> > On Sun, 11 Nov 2018 at 14:46, Jonas Frey <jf at probe-networks.de>
> > wrote:
> > > Hi Mohammad,
> > >
> > > thats a typo, its nand_format (note the underscore).
> > > Am Sonntag, den 11.11.2018, 05:31 -0500 schrieb Mohammad Khalil:
> > > > => reset
> > > >
> > > >
> > > > U-Boot 1.1.6-JNPR-2.7 (Build time: Nov 26 2013 - 19:04:49)
> > > >
> > > > Initializing memory this may take some time...
> > > > Measured DDR clock 266.62 MHz
> > > > SRX_100H2 board revision major:1, minor:0, serial #: BZ4214AF1453
> > > > OCTEON CN5020-SCP pass 1.1, Core clock: 500 MHz, DDR clock: 266
> > > MHz
> > > > (532
> > > > Mhz data rate)
> > > > DRAM:  2048 MB
> > > > Starting Memory POST...
> > > > Checking datalines... OK
> > > > Checking address lines... OK
> > > > Checking 512K memory for U-Boot... OK.
> > > > Running U-Boot CRC Test... OK.
> > > > Flash:  4 MB
> > > > USB:   scanning bus for devices... 4 USB Device(s) found
> > > >        scanning bus for storage devices... Read Error for
> > > > STMicroelectronics device 0
> > > > Not intializing this device, disabling autoboot
> > > > Device may need formatting, please issue command :
> > > >         <nand_format> at console prompt to format
> > > > 2 Storage Device(s) found
> > > > Clearing DRAM........ done
> > > > BIST check passed.
> > > > Boot Media: nand-flash usb
> > > > Net:   pic init done (err = 0)octeth0
> > > > POST Passed
> > > > Press SPACE to abort autoboot in 1 seconds
> > > > => nand-format
> > > > Unknown command 'nand-format' - try 'help'
> > > >
> > > >
> > > > On Sun, 11 Nov 2018 at 04:17, Muhammad Atif Jauhar <atif.jauhar at g
> > > mail
> > > > .com>
> > > > wrote:
> > > >
> > > > >
> > > > > Hi Khalil,
> > > > >
> > > > > Kindly follow below link to recover it.
> > > > >
> > > > >
> > > > > https://forums.juniper.net/t5/SRX-Services-Gateway/Boot-problem
> > > -of-
> > > > > UBoot-srx240-having-status-LED-red/td-p/211103
> > > > >
> > > > > Regards,
> > > > >
> > > > > Muhammad Atif Jauhar
> > > > > (+966-56-00-04-985)
> > > > >
> > > > >
> > > > > On Sun, Nov 11, 2018 at 11:36 AM Mohammad Khalil <eng.mssk at gmai
> > > l.co
> > > > > m>
> > > > > wrote:
> > > > >
> > > > > >
> > > > > > Hello all
> > > > > > I have my Juniper SRX 100h stuck in the u-boot mode
> > > > > > I have tried to download a new image on a USB stick , plugged
> > > it
> > > > > > into the
> > > > > > device and tried to upgrade with no luck
> > > > > > Looked around but could not find a solution , anyone can help
> > > > > > please?
> > > > > >
> > > > > > BR,
> > > > > > Mohammad
> > > > > > _______________________________________________
> > > > > > juniper-nsp mailing list juniper-nsp at puck.nether.net
> > > > > > https://puck.nether.net/mailman/listinfo/juniper-nsp
> > > > > >
> > > > _______________________________________________
> > > > juniper-nsp mailing list juniper-nsp at puck.nether.net
> > > > https://puck.nether.net/mailman/listinfo/juniper-nsp
> > >
>