[rbak-nsp] Help me to indentify this problem!

Tanan Satayapiwat tanan.satayapiwat at ericsson.com
Mon Aug 9 06:43:19 EDT 2010


I mean not in the supported way. In other words, it's not documented and you're on your own :-)

-----Original Message-----
From: Marcin Kuczera [mailto:marcin at leon.pl] 
Sent: Monday, August 09, 2010 12:41 PM
To: Tanan Satayapiwat
Cc: Navin Nepali; redback-nsp at puck.nether.net
Subject: Re: [rbak-nsp] Help me to indentify this problem!

Tanan Satayapiwat wrote:
> "Compact Flash Test : FAILED"
>  
> Definitely need a replacement. Note that this is internal compact 
> flash so it's not field-replacable.


It IS replacable.
Just open the cover, replace 512k CF with ANY flash but:
- can not be Kingstone, SE works with Kingstone but it is extremally slow.
- best - tested is SANDISK Extreme III, any size - tested with max 8G capacity
- need TFTP server with SEOS image

Regards,
Marcin



>  
> Tanan
> 
> ----------------------------------------------------------------------
> --
> *From:* Navin Nepali [mailto:navin_n at yahoo.com]
> *Sent:* Monday, August 09, 2010 12:06 PM
> *To:* Tanan Satayapiwat
> *Subject:* RE: [rbak-nsp] Help me to indentify this problem!
> 
> Ok Tanan..i got some log now.
>  
> [0]Booting(2)....
> Enabling L1/L2 Caches...
> Reset Cause:
>         Power On Reset (PPC/TDM Subsystems)
> 
> Cold boot, clearing out vxWorks memory space SCC RAM controller 
> Initialized
> PPC1: Initialized PPC1
> Detected Peer XC-RP, will try to establish link....
> PPC1: Polling for commands from PPC0
> Monitor 0 channel 1 Voltage is 1.511 V (9AC0) Monitor 0 channel 2 
> Voltage is 1.787 V (B700) Monitor 1 channel 1 Voltage is 5.028 V 
> (80C0) Monitor 1 channel 2 Voltage is 3.348 V (AB80) Monitor 1 channel 
> 3 Voltage is 2.524 V (8140) Monitor 1 channel 4 Voltage is 2.109 V 
> (D800) Monitor 0 Temp = 40.00 C (2800) Monitor 1 Temp = 28.50 C (1C80) 
> ATA device not present or not responding Reading MAC address Backplane 
> EEPROM MAC address 00:30:88:01:FA:4C Welcome to SmartFirmware(tm) for 
> Redback PowerPC Copyright (c) 1999-2005 by Redback Networks, Inc. 
> version 1.0b1272
> SmartFirmware(tm) Copyright 1996-2000 by CodeGen, Inc.
> All Rights Reserved.
> Executing POST
>                            PPC0 L2 Cache Test : PASSED
>                           Sandisk Screen Test : PASSED
>                                   Bridge Test : PASSED
>                                PPC SDRAM Test : PASSED
>                                SCC SDRAM Test : PASSED
>                            Serial(16552) Test : PASSED
>                                 Ethernet Test : PASSED
>                               ISA Bridge Test : PASSED
>                                    Forte Test : PASSED
>                                     Opus Test : PASSED
>                                      Max Test : PASSED
>                                     Bits Test : PASSED
>                                      SCC Test : PASSED
>                            Compact Flash Test : FAILED
>                                  PC Card Test : PASSED FAILED (1 
> error) Loop 1 of 1,  2010/08/09 09:51:21 POST FAILED
> Auto-boot in 0 seconds - press se* to abort, CR-CR to boot:       
> inflating image from 7050959 bytes to
> Flushing L1 D-Cache, @ 0x10000, 40591497 bytes
> PPC1: PPC1 image loaded @0x10000
> error: error while trying to load or boot ok CR-CR no such symbol 
> "CR-CR"
> error: undefined word
> ok se*
> no such symbol "se*"
> error: undefined word
> ok
> ok
> ok
> ok
> [0]Booting(2)....
> Enabling L1/L2 Caches...
> Reset Cause:
>         Power On Reset (PPC/TDM Subsystems)
> 
> Cold boot, clearing out vxWorks memory space SCC RAM controller 
> Initialized
> PPC1: Initialized PPC1
> Detected Peer XC-RP, will try to establish link....
> PPC1: Polling for commands from PPC0
> Monitor 0 channel 1 Voltage is 1.513 V (9B00) Monitor 0 channel 2 
> Voltage is 1.787 V (B700) Monitor 1 channel 1 Voltage is 9.988 V 
> (FFC0) Monitor 1 channel 2 Voltage is 4.994 V (FFC0) Monitor 1 channel 
> 3 Voltage is 4.994 V (FFC0) Monitor 1 channel 4 Voltage is 2.497 V 
> (FFC0) Monitor 0 Temp = 39.75 C (27C0) Monitor 1 Temp = 0.-25 C 
> (FFFFFFC0) ATA device not present or not responding Reading MAC 
> address Backplane EEPROM MAC address 00:30:88:01:FA:4C Welcome to 
> SmartFirmware(tm) for Redback PowerPC Copyright (c) 1999-2005 by 
> Redback Networks, Inc. version 1.0b1272
> SmartFirmware(tm) Copyright 1996-2000 by CodeGen, Inc.
> All Rights Reserved.
> Executing POST
>                            PPC0 L2 Cache Test : PASSED
>                           Sandisk Screen Test : PASSED
>                                   Bridge Test : PASSED
>                                PPC SDRAM Test : PASSED
>                                SCC SDRAM Test : PASSED
>                            Serial(16552) Test : PASSED
>                                 Ethernet Test : PASSED
>                               ISA Bridge Test : PASSED
>                                    Forte Test : PASSED
>                                     Opus Test : PASSED
>                                      Max Test : PASSED
>                                     Bits Test : PASSED
>                                      SCC Test : PASSED
>                            Compact Flash Test : FAILED
>                                  PC Card Test : PASSED FAILED (1 
> error) Loop 1 of 1,  2010/08/09 09:54:37 POST FAILED
> Auto-boot in 0 seconds - press se* to abort, CR-CR to boot:       
> inflating image from 7050959 bytes to
> Flushing L1 D-Cache, @ 0x10000, 40591497 bytes
> PPC1: PPC1 image loaded @0x10000
> error: error while trying to load or boot
>  
>  
> Seems like Compact Flash card is not working.
>  
> So how to replace it?
> 
> 
> --- On *Mon, 8/9/10, Tanan Satayapiwat
> /<tanan.satayapiwat at ericsson.com>/* wrote:
> 
> 
>     From: Tanan Satayapiwat <tanan.satayapiwat at ericsson.com>
>     Subject: RE: [rbak-nsp] Help me to indentify this problem!
>     To: "Navin Nepali" <navin_n at yahoo.com>,
>     "redback-nsp at puck.nether.net" <redback-nsp at puck.nether.net>
>     Date: Monday, August 9, 2010, 2:35 PM
> 
>     then re-seat it and see if there is an error during boot up.
>      
>     Tanan
> 
>     ------------------------------------------------------------------------
>     *From:* Navin Nepali [mailto:navin_n at yahoo.com]
>     *Sent:* Monday, August 09, 2010 11:04 AM
>     *To:* redback-nsp at puck.nether.net; Tanan Satayapiwat
>     *Subject:* RE: [rbak-nsp] Help me to indentify this problem!
> 
>     I didn't get any messages from the console.
>      
> 
> 
>     --- On *Mon, 8/9/10, Tanan Satayapiwat
>     /<tanan.satayapiwat at ericsson.com>/* wrote:
> 
> 
>         From: Tanan Satayapiwat <tanan.satayapiwat at ericsson.com>
>         Subject: RE: [rbak-nsp] Help me to indentify this problem!
>         To: "Navin Nepali" <navin_n at yahoo.com>,
>         "redback-nsp at puck.nether.net" <redback-nsp at puck.nether.net>
>         Date: Monday, August 9, 2010, 2:28 PM
> 
>         Connect to the console of Slot 7 and if it's cycling through the
>         reboot, you may see some notable errors.
>          
>         Tanan
> 
>         ------------------------------------------------------------------------
>         *From:* redback-nsp-bounces at puck.nether.net
>         [mailto:redback-nsp-bounces at puck.nether.net] *On Behalf Of
>         *Navin Nepali
>         *Sent:* Monday, August 09, 2010 8:53 AM
>         *To:* redback-nsp at puck.nether.net
>         *Subject:* [rbak-nsp] Help me to indentify this problem!
> 
>         Today my se800 box went down suddenly. The active XCRP3 card's
>         status went to fail and the standby card didn't respond. I
>         manually pulled out both cards and re-inserted. The card in Slot
>         7 is still in Failed state while the standby card recovered. Now
>         the system is running from the standby card.
>          
>         If I do "show hardware", the slot 7's type is Unknown. So this
>         means the card has hardware fault or still can be used?
>          
>          
> 
> 
> 
> 
> 
> ----------------------------------------------------------------------
> --
> 
> _______________________________________________
> redback-nsp mailing list
> redback-nsp at puck.nether.net
> https://puck.nether.net/mailman/listinfo/redback-nsp




More information about the redback-nsp mailing list