[rbak-nsp] Regarding the XCRP3 Card
Marcin Kuczera
marcin at leon.pl
Mon May 21 16:51:44 EDT 2012
Navin Nepali wrote:
> Hi!!
> I am getting this message during the boot of the XCRP3 card and it is
> not booting. What may be the problem?
>
> Issue of CF card???
As you have working XCRP3, please run diagnostics on stanby card.
1. shutdown card in the other XCRP slot than actvie
2. turn on on-demand diagnostics state
3. run diagnostics (level3)
You should get the answer, I mean - if diagnostics are ok, then CF must
be replaced.
(at least I think so..)
Regards,
Marcin
> //
> /I am standby
> set max route entry to 190650
> filtered interface fxp0
> booted_partition: 0
> boot device: wd1
> root on wd1a dumps on wd2b
> mountroot: trying msdos...
> mountroot: trying nfs...
> mountroot: trying ffs...
> Standby xcrp's time is in sync with the active's ...
> root file system type: ffs
> init: copying out path `/p01/sbin/init' 15
> ** /dev/rwd1a
> ** Last Mounted on /
> ** Root file system
> ** Phase 1 - Check Blocks and Sizes
> trap type 100 at 5bd1c6c
> panic: trap type 100 at 5bd1c6c, Machine Status (SRR1) 0x00001032, DAR:
> 0x0195e008/
> /syncing disks... done
> siara2k: dumpsys called/
> /dumping to dev 10,33 offset 8/
> /[0]Booting(2)....
> Enabling L1/L2 Caches.../
> /Reset Cause:
> SCC Watchdog Reset (PPC Subsystem ONLY)
> ISA reset (PPC Subsystem ONLY)/
>
> /Cold boot, clearing out vxWorks memory space
> Writing SCC Reset into 0x04EBFFE8
> SCC RAM controller Initialized
> Detected Peer XC-RP, will try to establish link....
> PPC1: Initialized PPC1
> Monitor 0 channel 1 Voltage is 1.513 V (9B00)
> PPC1: Polling for commands from PPC0
> Monitor 0 channel 2 Voltage is 1.777 V (B600)
> Monitor 1 channel 1 Voltage is 5.028 V (80C0)
> Monitor 1 channel 2 Voltage is 3.338 V (AB00)
> Monitor 1 channel 3 Voltage is 2.534 V (81C0)
> Monitor 1 channel 4 Voltage is 2.111 V (D840)
> Monitor 0 Temp = 30.50 C (1E80)
> Monitor 1 Temp = 28.00 C (1C00)
> Reading MAC address
> Backplane EEPROM MAC address 00:30:88:01:FA:4C
> Welcome to SmartFirmware(tm) for Redback PowerPC Copyright (c) 1999-2005
> by Redback Networks, Inc. version 1.0b1272
> SmartFirmware(tm) Copyright 1996-2000 by CodeGen, Inc.
> All Rights Reserved.
> Executing POST
> PPC0 L2 Cache Test : PASSED
> Sandisk Screen Test : PASSED
> Bridge Test : PASSED
> PPC SDRAM Test : PASSED
> SCC SDRAM Test : PASSED
> Serial(16552) Test : PASSED
> Ethernet Test : PASSED
> ISA Bridge Test : PASSED
> Forte Test : PASSED
> Opus Test : PASSED
> Max Test : PASSED
> Bits Test : PASSED
> SCC Test : PASSED
> Compact Flash Test : PASSED
> PC Card Test : PASSED
> PASSED Loop 1 of 1, 2012/05/20 15:10:06
> POST PASSED
> Auto-boot in 0 seconds - press se* to abort, CR-CR to boot:
> inflating image from 9142372 bytes to
> Flushing L1 D-Cache, @ 0x10000, 51525652 bytes
> PPC1: PPC1 image loaded @0x10000
> -
> verifying checksum of /p01/netbsd ... succeeded
> Flushing L1 D-cache, @ 0x5A00000, 2631657 bytes. Please wait....
> Syncing L1-I cache, Please wait....
> launching...
> Start of symbol table: 0x5d96000
> End of symbol table: 0x60187e9
> OFW VERSION: PowerPC,1.0b1272
> MINIKERNEL VERSION: 23
> BOOTPATH: ///pci/isa at B/ide at i1F0/disk at 1,0:a/
> /BOOTARGS: /p01/netbsd
> BOOTDIR: /p01
> Kernel args[2]: -d
> [ preserving 2631660 bytes of netbsd ELF symbol table ]
> pmap_bootstrap: Kernel Start @0x05A00000 to Kernel End @ 0x05D95F50
> pmap_bootstrap: physmem: 240384 pages
> pmap_bootstrap: # of available mem regions: 1
> pmap_bootstrap:after DDB - avail mem regions: 2
> ptab_cnt: 131072
> Page Table @ 0x6800000, size: 0x00800000
> UVM Physical memory: start 0xdeaddead, size 0x00000000
> dump buffer @ PA: 0x07001000
> Phys. mem mapped by UVM: start 0x07047000, size 0x389b9000
> Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001
> The NetBSD Foundation, Inc. All rights reserved.
> Copyright (c) 1982, 1986, 1989, 1991, 1993
> The Regents of the University of California. All rights reserved./
> /NetBSD 1.5.3 (CUSTOM_XC2) #0: Fri Jan 29 16:44:01 PST 2010
>
> //sysbuild at SWB-node05:/project/sysbuild-extra/builds-ec/REL_6_2/obj/netbsd-kernels/CUSTOM_XC2/
> <mailto:sysbuild at SWB-node05:/project/sysbuild-extra/builds-ec/REL_6_2/obj/netbsd-kernels/CUSTOM_XC2>
> /CPU: 750 (Revision 8302)
> total memory = 939 MB
> avail memory = 885 MB
> using 1024 buffers containing 4096 KB of memory
> Dumpspace: 0xe93a8000
> XCRP version 0 (XCRP_VER_2dot6) model 1
> Backplane Id: 0x3
> The controller card is in slot 8
> Chassis product code: 8Y
> mainbus0 (root)
> vxmem0 at mainbus0cpu0 at mainbus0
> L2CR: 0xFD81408C: : 1MB Pipelined synchronous late-write SRAM with
> parity backside cache enabled
> scc0 at mainbus0 Local SCC @ 0x60000000 Remote SCC @ 0x70000000
> SCC Memory Size (from OFW) 256 MB
> scc_init: Mapped SCC Registers @0xe93bc000
> scc_init: Mapped vxWorks memory console @0xe93bd000
> Mapping in 0x02000000 bytes starting @ 0x64000000 for PTD driver
> Mapped REMOTE SCC Memory @0xe94bd000
> Init 0x08000000 bytes of SCC SDRAM @ 0x68000000 for RDB...Done
> grackle0 at mainbus0
> pci0 at grackle0 bus 0
> pci0: i/o space, memory space enabled
> pchb0 at pci0 dev 0 function 0
> pchb0: Motorola product 0x0004 (rev. 0x14)
> pcib0 at pci0 dev 11 function 0
> pcib0: Symphony Labs 83C553 PCI-ISA Bridge (rev. 0x10)
> Symphony Labs 82C105 (IDE mass storage, interface 0x8f, revision 0x05)
> at pci0 dev 11 function 1 not configured
> fxp0 at pci0 dev 14 function 0: i82559S Ethernet, rev 9
> Establishing IRQ 20 of type 3 level 5, func 0x5a03044
> fxp0: interrupting at irq 20
> fxp0: detected 64 word EEPROM
> Found local-mac-address property
> OF MAC Address: 0x0 0x30 0x88 0x1 0xFA 0x4C
> fxp0: Ethernet address 00:30:88:01:fa:4c, 10/100 Mb/s
> inphy0 at fxp0 phy 1: i82555 10/100 media interface, rev. 4
> inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
> isa0 at pcib0
> com0 at isa0 port 0x4500-0x4507 irq 22: ns16550a, working fifo
> com0: console
> Establishing IRQ 22 of type 3 level 3, func 0x5a09370
> wdcprobe:0: before reset, st0=0x50, st1=0x0
> wdc1 at isa0 port 0x470-0x477 irq 18
> Establishing IRQ 18 of type 2 level 6, func 0x5a0afec
> wdc1:0: before reset, st0=0x50, st1=0x0
> wd1 at wdc1 channel 0 drive 0: <SMART CF> <multi_single><SMART>
> <00001011540001053652> <20060729>
> wd1: drive supports 16-sector pio transfers, lba addressing
> wd1: 488 MB, 993 cyl, 16 head, 63 sec, 512 bytes/sect x 1000944 sectors
> wd1: drive supports PIO mode 4, DMA mode 2
> wdcprobe:0: before reset, st0=0x50, st1=0x0
> wdc2 at isa0 port 0x170-0x177 irq 10
> Establishing IRQ 10 of type 2 level 6, func 0x5a0afec
> wdc2:0: before reset, st0=0x50, st1=0x0
> wd2 at wdc2 channel 0 drive 0: <STI Flash 7.2.0 RBAKCF1GBJI>
> <multi_single><STI Flash> < STI1J2d106362191959> <12-15-04>
> wd2: drive supports 16-sector pio transfers, lba addressing
> wd2: 977 MB, 1986 cyl, 16 head, 63 sec, 512 bytes/sect x 2001888 sectors
> wd2: drive supports PIO mode 4
> rtc0 at isa0 port 0x7fff8-0x7ffff iomem 0xfd000000-0xfd000007ds1747 reg
> attached @ 0xe94d5ff8
> ds1747 nvr attached @ 0xe94d6000
> Current date : century : 20, 05/20/12 (Mon)
> Current time : 15:10:40
> clpd67xx0 at isa0 port 0x3e0-0x3e1 iomem
> 0xfe0003e0-0xfe0003e1Establishing IRQ 11 of type 3 level 6, func 0x5bf3db0
> CL-PD6720 rev 12, status = 0xdf, flag = 0x1
> ipc0 at mainbus0Mapped Shared Memory Block @ PA 0x5500000 to VA 0x5500000
> Establishing IRQ 30 of type 3 level 5, func 0x5bd9324
> 107 EPIC : Step 1, Device ID: 0, Vendor ID: 0
> 107 EPIC : # IRQs: 23, # CPUs: 0, Version ID: 2
> flashattach: configuring 1 flash device(s)
> PPA Transport Driver v. 1.0
> init_ptd_sccmem: Init. SCC SDRAM for PTD driver...Done
> P2P memory: local=0x6401f000 remote=0x7401f000->0xe9658000 size=1048576
> ## ptdmem_add: npg 7648 size 31326208 bmapsz 956 (pg 0xe1255000) ##
> ptd_extraspace = 0x6401e000
> remote_ptd_extraspace = 0x7401e000
> Mapped remote_ptd_extraspace at 0xe9758000
> pdtattach: configuring 16 pdt devices
> ephemeral range was 49152-65535, new range is 56608-65535
> Initializing XCRP INFO area @ 0xfd000000...succeeded
> Displaying previous reboot data.../
> /Reboot Recorded on 15:09:49 05/20/12
> Temperature/Voltage information:
> Monitor 0 Temp = 30.50 C Monitor 1 Temp = 28.00 C
> Monitor 0 channel 1 Voltage 1.513 V Monitor 0 channel 2 Voltage 1.777 V
> Monitor 1 channel 1 Voltage 5.028 V Monitor 1 channel 2 Voltage 3.338 V
> Monitor 1 channel 3 Voltage 2.534 V Monitor 1 channel 4 Voltage 2.111 V
> OFW Reset Cause: SCC Watchdog Reset ISA reset
> BSD Reboot recorded on 15:09:17 05/20/12 (Sun)
> Reboot by BSD - BSD_REBOOT_ON_PANIC
> Initializing RTC NVRAM LOG area @ fd001400 succeeded
> Initializing XCRP L2 Cache Log area @ 0xfd06fe00...succeeded
> Using local P2P memory @ PA 0x6401F000
> P2P device:
> Carving scc mem 0x68000000
> header_start = 0x68000020 no_of_header_blocks 1
> vxWorks is booting!!!!!
> Waiting for Vxworks to find active and standby...
> ....VX Redundancy state: ### VX_BOOT_DONE TRUE ###
> .VX Redundancy state: ### VERSION B3 TRUE ###
> .VX Redundancy state: ### VX_M2M_LINKUP TRUE ###
> xcrp will let the active sync timeNotifying all processes of M2MUP status
> VX Redundancy state: ### VX_IS_ACTIVE FALSE ###
> Notifying all processes of STANDBY status
> Using remote P2P memory @ PA 0xE9658000
> VX Redundancy state: ### VX_ACTSTB_DECIDED TRUE ###
> start using scc to keep time.../
> /I am standby
> set max route entry to 190650
> filtered interface fxp0
> booted_partition: 0
> boot device: wd1
> root on wd1a dumps on wd2b
> mountroot: trying msdos...
> mountroot: trying nfs...
> mountroot: trying ffs...
> Standby xcrp's time is in sync with the active's ...
> root file system type: ffs
> init: copying out path `/p01/sbin/init' 15
> ** /dev/rwd1a
> ** Last Mounted on /
> ** Root file system
> ** Phase 1 - Check Blocks and Sizes
> trap type 100 at 5bd1c84
> panic: trap type 100 at 5bd1c84, Machine Status (SRR1) 0x00001032, DAR:
> 0x7fffddb0/
> /syncing disks... done
> siara2k: dumpsys called/
> /dumping to dev 10,33 offset 8/
> /[0]Booting(2)....
> Enabling L1/L2 Caches.../
> /Reset Cause:
> SCC Watchdog Reset (PPC Subsystem ONLY)
> ISA reset (PPC Subsystem ONLY)/
>
>
> ------------------------------------------------------------------------
>
> _______________________________________________
> redback-nsp mailing list
> redback-nsp at puck.nether.net
> https://puck.nether.net/mailman/listinfo/redback-nsp
More information about the redback-nsp
mailing list