[rbak-nsp] Regarding the XCRP3 Card

Sun May 20 13:41:33 EDT 2012

Hi!!
I am getting this message during the boot of the XCRP3 card and it is not booting. What may be the problem?

Issue of CF card???

I am standby
set max route entry to 190650
filtered interface fxp0
booted_partition: 0
boot device: wd1
root on wd1a dumps on wd2b
mountroot: trying msdos...
mountroot: trying nfs...
mountroot: trying ffs...
Standby xcrp's time is in sync with the active's ...
root file system type: ffs
init: copying out path `/p01/sbin/init' 15
** /dev/rwd1a
** Last Mounted on /
** Root file system
** Phase 1 - Check Blocks and Sizes
trap type 100 at 5bd1c6c
panic: trap type 100 at 5bd1c6c, Machine Status (SRR1) 0x00001032, DAR: 0x0195e008
syncing disks... done
siara2k: dumpsys called
dumping to dev 10,33 offset 8
[0]Booting(2)....
Enabling L1/L2 Caches...
Reset Cause:
        SCC Watchdog Reset (PPC Subsystem ONLY)
        ISA reset (PPC Subsystem ONLY)

Cold boot, clearing out vxWorks memory space
Writing SCC Reset into 0x04EBFFE8
SCC RAM controller Initialized
Detected Peer XC-RP, will try to establish link....
PPC1: Initialized PPC1
Monitor 0 channel 1 Voltage is 1.513 V (9B00)
PPC1: Polling for commands from PPC0
Monitor 0 channel 2 Voltage is 1.777 V (B600)
Monitor 1 channel 1 Voltage is 5.028 V (80C0)
Monitor 1 channel 2 Voltage is 3.338 V (AB00)
Monitor 1 channel 3 Voltage is 2.534 V (81C0)
Monitor 1 channel 4 Voltage is 2.111 V (D840)
Monitor 0 Temp = 30.50 C (1E80)
Monitor 1 Temp = 28.00 C (1C00)
Reading MAC address 
Backplane EEPROM MAC address 00:30:88:01:FA:4C
Welcome to SmartFirmware(tm) for Redback PowerPC Copyright (c) 1999-2005 by Redback Networks, Inc. version 1.0b1272
SmartFirmware(tm) Copyright 1996-2000 by CodeGen, Inc.
All Rights Reserved.
Executing POST
                           PPC0 L2 Cache Test : PASSED
                          Sandisk Screen Test : PASSED
                                  Bridge Test : PASSED
                               PPC SDRAM Test : PASSED
                               SCC SDRAM Test : PASSED
                           Serial(16552) Test : PASSED
                                Ethernet Test : PASSED
                              ISA Bridge Test : PASSED
                                   Forte Test : PASSED
                                    Opus Test : PASSED
                                     Max Test : PASSED
                                    Bits Test : PASSED
                                     SCC Test : PASSED
                           Compact Flash Test : PASSED
                                 PC Card Test : PASSED
PASSED Loop 1 of 1,  2012/05/20 15:10:06
POST PASSED
Auto-boot in 0 seconds - press se* to abort, CR-CR to boot:        
inflating image from 9142372 bytes to 
Flushing L1 D-Cache, @ 0x10000, 51525652 bytes 
PPC1: PPC1 image loaded @0x10000
-
verifying checksum of /p01/netbsd ... succeeded
Flushing L1 D-cache, @ 0x5A00000, 2631657 bytes. Please wait....
Syncing L1-I cache, Please wait....
launching...
Start of symbol table: 0x5d96000
End of symbol table: 0x60187e9
OFW VERSION: PowerPC,1.0b1272
MINIKERNEL VERSION: 23
BOOTPATH: /pci/isa at B/ide at i1F0/disk at 1,0:a
BOOTARGS: /p01/netbsd
BOOTDIR: /p01
Kernel args[2]: -d
[ preserving 2631660 bytes of netbsd ELF symbol table ]
pmap_bootstrap: Kernel Start @0x05A00000 to Kernel End @ 0x05D95F50
pmap_bootstrap: physmem: 240384 pages
pmap_bootstrap: # of available mem regions: 1
pmap_bootstrap:after DDB - avail mem regions: 2
ptab_cnt: 131072
Page Table @ 0x6800000, size: 0x00800000
UVM Physical memory: start 0xdeaddead, size 0x00000000
dump buffer @ PA: 0x07001000
Phys. mem mapped by UVM: start 0x07047000, size 0x389b9000
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.
NetBSD 1.5.3 (CUSTOM_XC2) #0: Fri Jan 29 16:44:01 PST 2010
    sysbuild at SWB-node05:/project/sysbuild-extra/builds-ec/REL_6_2/obj/netbsd-kernels/CUSTOM_XC2
CPU: 750 (Revision 8302)
total memory = 939 MB
avail memory = 885 MB
using 1024 buffers containing 4096 KB of memory
Dumpspace: 0xe93a8000
XCRP version 0 (XCRP_VER_2dot6) model 1
Backplane Id: 0x3
The controller card is in slot 8
Chassis product code: 8Y
mainbus0 (root)
vxmem0 at mainbus0cpu0 at mainbus0
L2CR: 0xFD81408C: : 1MB Pipelined synchronous late-write SRAM with parity backside cache enabled
scc0 at mainbus0 Local SCC @ 0x60000000 Remote SCC @ 0x70000000
SCC Memory Size (from OFW) 256 MB
scc_init: Mapped SCC Registers @0xe93bc000
scc_init: Mapped vxWorks memory console @0xe93bd000
Mapping in 0x02000000 bytes starting @ 0x64000000 for PTD driver
Mapped REMOTE SCC Memory @0xe94bd000
Init 0x08000000 bytes of SCC SDRAM @ 0x68000000 for RDB...Done
grackle0 at mainbus0
pci0 at grackle0 bus 0
pci0: i/o space, memory space enabled
pchb0 at pci0 dev 0 function 0
pchb0: Motorola product 0x0004 (rev. 0x14)
pcib0 at pci0 dev 11 function 0
pcib0: Symphony Labs 83C553 PCI-ISA Bridge (rev. 0x10)
Symphony Labs 82C105 (IDE mass storage, interface 0x8f, revision 0x05) at pci0 dev 11 function 1 not configured
fxp0 at pci0 dev 14 function 0: i82559S Ethernet, rev 9
Establishing IRQ 20 of type 3 level 5, func 0x5a03044
fxp0: interrupting at irq 20
fxp0: detected 64 word EEPROM
Found local-mac-address property
OF MAC Address: 0x0 0x30 0x88 0x1 0xFA 0x4C 
fxp0: Ethernet address 00:30:88:01:fa:4c, 10/100 Mb/s
inphy0 at fxp0 phy 1: i82555 10/100 media interface, rev. 4
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
isa0 at pcib0
com0 at isa0 port 0x4500-0x4507 irq 22: ns16550a, working fifo
                                                              com0: console
Establishing IRQ 22 of type 3 level 3, func 0x5a09370
wdcprobe:0: before reset, st0=0x50, st1=0x0
wdc1 at isa0 port 0x470-0x477 irq 18
Establishing IRQ 18 of type 2 level 6, func 0x5a0afec
wdc1:0: before reset, st0=0x50, st1=0x0
wd1 at wdc1 channel 0 drive 0: <SMART CF> <multi_single><SMART> <00001011540001053652> <20060729>
wd1: drive supports 16-sector pio transfers, lba addressing
wd1: 488 MB, 993 cyl, 16 head, 63 sec, 512 bytes/sect x 1000944 sectors
wd1: drive supports PIO mode 4, DMA mode 2
wdcprobe:0: before reset, st0=0x50, st1=0x0
wdc2 at isa0 port 0x170-0x177 irq 10
Establishing IRQ 10 of type 2 level 6, func 0x5a0afec
wdc2:0: before reset, st0=0x50, st1=0x0
wd2 at wdc2 channel 0 drive 0: <STI Flash 7.2.0 RBAKCF1GBJI> <multi_single><STI Flash> < STI1J2d106362191959> <12-15-04>
wd2: drive supports 16-sector pio transfers, lba addressing
wd2: 977 MB, 1986 cyl, 16 head, 63 sec, 512 bytes/sect x 2001888 sectors
wd2: drive supports PIO mode 4
rtc0 at isa0 port 0x7fff8-0x7ffff iomem 0xfd000000-0xfd000007ds1747 reg attached @ 0xe94d5ff8
ds1747 nvr attached @ 0xe94d6000
Current date : century : 20, 05/20/12 (Mon)
Current time : 15:10:40
clpd67xx0 at isa0 port 0x3e0-0x3e1 iomem 0xfe0003e0-0xfe0003e1Establishing IRQ 11 of type 3 level 6, func 0x5bf3db0
CL-PD6720 rev 12, status = 0xdf, flag = 0x1
ipc0 at mainbus0Mapped Shared Memory Block @ PA 0x5500000 to VA 0x5500000
Establishing IRQ 30 of type 3 level 5, func 0x5bd9324
107 EPIC : Step 1, Device ID: 0, Vendor ID: 0
107 EPIC : # IRQs: 23, # CPUs: 0, Version ID: 2
flashattach: configuring 1 flash device(s)
PPA Transport Driver v. 1.0
init_ptd_sccmem: Init. SCC SDRAM for PTD driver...Done
P2P memory: local=0x6401f000 remote=0x7401f000->0xe9658000 size=1048576
## ptdmem_add: npg 7648  size 31326208 bmapsz 956 (pg 0xe1255000) ##
ptd_extraspace = 0x6401e000
remote_ptd_extraspace = 0x7401e000
Mapped remote_ptd_extraspace at 0xe9758000
pdtattach: configuring 16 pdt devices
ephemeral range was 49152-65535, new range is 56608-65535
Initializing XCRP INFO area @ 0xfd000000...succeeded 
Displaying previous reboot data...
Reboot Recorded on 15:09:49 05/20/12
Temperature/Voltage information:
Monitor 0 Temp = 30.50 C Monitor 1 Temp = 28.00 C
Monitor 0 channel 1 Voltage 1.513 V Monitor 0 channel 2 Voltage 1.777 V
Monitor 1 channel 1 Voltage 5.028 V Monitor 1 channel 2 Voltage 3.338 V
Monitor 1 channel 3 Voltage 2.534 V Monitor 1 channel 4 Voltage 2.111 V
OFW Reset Cause: SCC Watchdog Reset  ISA reset 
BSD Reboot recorded on 15:09:17 05/20/12 (Sun)
Reboot by BSD - BSD_REBOOT_ON_PANIC
Initializing RTC NVRAM LOG area @ fd001400 succeeded
Initializing XCRP L2 Cache Log area @ 0xfd06fe00...succeeded 
Using local P2P memory @ PA 0x6401F000
P2P device: 
Carving scc mem 0x68000000
header_start = 0x68000020 no_of_header_blocks 1
vxWorks is booting!!!!!
Waiting for Vxworks to find active and standby...
....VX Redundancy state:  ###  VX_BOOT_DONE TRUE  ###
.VX Redundancy state:  ###  VERSION B3 TRUE  ###
.VX Redundancy state:  ###  VX_M2M_LINKUP TRUE  ###
xcrp will let the active sync timeNotifying all processes of M2MUP status
VX Redundancy state:  ###  VX_IS_ACTIVE FALSE  ###
Notifying all processes of STANDBY status
Using remote P2P memory @ PA 0xE9658000
VX Redundancy state:  ###  VX_ACTSTB_DECIDED TRUE  ###
start using scc to keep time...
I am standby
set max route entry to 190650
filtered interface fxp0
booted_partition: 0
boot device: wd1
root on wd1a dumps on wd2b
mountroot: trying msdos...
mountroot: trying nfs...
mountroot: trying ffs...
Standby xcrp's time is in sync with the active's ...
root file system type: ffs
init: copying out path `/p01/sbin/init' 15
** /dev/rwd1a
** Last Mounted on /
** Root file system
** Phase 1 - Check Blocks and Sizes
trap type 100 at 5bd1c84
panic: trap type 100 at 5bd1c84, Machine Status (SRR1) 0x00001032, DAR: 0x7fffddb0
syncing disks... done
siara2k: dumpsys called
dumping to dev 10,33 offset 8
[0]Booting(2)....
Enabling L1/L2 Caches...
Reset Cause:
        SCC Watchdog Reset (PPC Subsystem ONLY)
        ISA reset (PPC Subsystem ONLY)
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://puck.nether.net/pipermail/redback-nsp/attachments/20120520/8c028f61/attachment.html>