[cisco-voip] H323 to CM 6.1.2

[Scott Voll]

That was the command I was looking for.  Thanks

but all the number are coming up with the right Dial peer.

I think I might have had a CSS on CFA that was causing some of the
issue..... we will see.

Scott

On Mon, Aug 25, 2008 at 12:19 PM, Joe Cisco <smetsysocsic at gmail.com> wrote:

> Ok. My next obvious question, is this... does the calling search space
> on the h323 gateway (in the GUI) have the ability to see all needed
> extensions?
>
> If so, if you do a "show dialplan number XXXX" on the gateway (where
> XXXX is an actual 4 digit extension) do you see it match the voip dial
> peer? I'd try it several times for different extensions.
>
> -Joe C.
>
> On Mon, Aug 25, 2008 at 2:11 PM, Scott Voll <svoll.voip at gmail.com> wrote:
> > yep
> > destination-pattern ....
> >
> > it worked just fine with CM 4.1.  the cm 6.1 is a different IP so I just
> > changed the session target address.
> >
> > Scott
> >
> > On Mon, Aug 25, 2008 at 12:03 PM, Joe Cisco <smetsysocsic at gmail.com>
> wrote:
> >>
> >> Does the VoIP dial peer include all the extensions in question?
> >>
> >> Example, the following voip dial peer only covers 4 digit extensions
> >> starting with the number "4"
> >>
> >> !
> >> dial-peer voice 4000 voip
> >>  description 4XXX extension to publisher
> >>  preference 1
> >>  destination-pattern 4...
> >>  progress_ind setup enable 3
> >>  progress_ind progress enable 8
> >>  voice-class h323 1
> >>  session target ipv4:172.16.1.10
> >>  dtmf-relay h245-alphanumeric
> >>  codec g711ulaw
> >>  no vad
> >> !
> >>
> >> -Joe C.
> >>
> >> On Mon, Aug 25, 2008 at 1:34 PM, Scott Voll <svoll.voip at gmail.com>
> wrote:
> >> > no.  did I need to reboot?
> >> >
> >> > Q931 looks normal.... but I'm not seeing the problem ones as I'm not
> >> > sure
> >> > when they are happening.  It's not consistant.
> >> >
> >> > Scott
> >> >
> >> >
> >> > On Mon, Aug 25, 2008 at 11:28 AM, Ryan West <rwest at zyedge.com> wrote:
> >> >>
> >> >> Debug isdn q931 to make sure that your system is generating the
> >> >> message,
> >> >> make sure it's actually hitting your gateway.  Did you reboot your
> >> >> router
> >> >> after making the change?
> >> >>
> >> >>
> >> >>
> >> >> -ryan
> >> >>
> >> >>
> >> >>
> >> >> From: cisco-voip-bounces at puck.nether.net
> >> >> [mailto:cisco-voip-bounces at puck.nether.net] On Behalf Of Scott Voll
> >> >> Sent: Monday, August 25, 2008 2:23 PM
> >> >> To: cisco-voip at puck.nether.net
> >> >> Subject: [cisco-voip] H323 to CM 6.1.2
> >> >>
> >> >>
> >> >>
> >> >> I have a VGW (CMM) with a couple PRI's connected to my new CM 6.1.2
> >> >> cluster.
> >> >>
> >> >>
> >> >>
> >> >> I am having reports of calls not going through.(your call cannot be
> >> >> completed as dialed).
> >> >>
> >> >>
> >> >>
> >> >> All I did on the dial peers was change the IPV4:(new server cluster
> >> >> IP).
> >> >> All looks good
> >> >>
> >> >>
> >> >>
> >> >> is it an IOS issue or a CM issue.
> >> >>
> >> >>
> >> >>
> >> >> I call a DID and get the message and call it again and it works.  I
> >> >> thought it was my cell phone, but I'm getting more reports of it.
> >> >>
> >> >>
> >> >>
> >> >> if anyone can give me a starting spot, I would like to trouble shoot
> >> >> this.
> >> >>
> >> >>
> >> >>
> >> >> TIA
> >> >>
> >> >>
> >> >>
> >> >> Scott
> >> >
> >> > _______________________________________________
> >> > cisco-voip mailing list
> >> > cisco-voip at puck.nether.net
> >> > https://puck.nether.net/mailman/listinfo/cisco-voip
> >> >
> >> >
> >
> >
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://puck.nether.net/pipermail/cisco-voip/attachments/20080825/fcbe95ca/attachment.html>