[cisco-voip] CISCO 2851

[Nick Griffin]

So, you should be able to obtain snmp information from the router now, via
your application. Assuming you have not tied an access-list to your
community configured. That is saying that you have not configured the router
to send snmp traps to a snmp receiver application:
Rack1R6(config)#do sh snmp
Chassis: 00000000
0 SNMP packets input
    0 Bad SNMP version errors
    0 Unknown community name
    0 Illegal operation for community name supplied
    0 Encoding errors
    0 Number of requested variables
    0 Number of altered variables
    0 Get-request PDUs
    0 Get-next PDUs
    0 Set-request PDUs
0 SNMP packets output
    0 Too big errors (Maximum packet size 1500)
    0 No such name errors
    0 Bad values errors
    0 General errors
    0 Response PDUs
    0 Trap PDUs

SNMP logging: enabled
    Logging to 1.1.1.1.162, 0/10, 0 sent, 0 dropped.
Rack1R6(config)#do sh run | i snmp
snmp-server community cisco RO
snmp-server host 1.1.1.1 version 2c PubLIC


On Tue, Jun 3, 2008 at 3:18 PM, David Toledo <DavidT at morganmint.com> wrote:

>  Sorry guys
>
>
>
>
>
> I just need the be able to monitor the cisco router but the snmp must be
> enable to use my application
>
> To gather all the information to manage all my devices.
>
>
>
> Now is showing:
>
> SNMP logging: disabled
>
>
>
>
>
>
>
>
>  ------------------------------
>
> *From:* cisco-voip-bounces at puck.nether.net [mailto:
> cisco-voip-bounces at puck.nether.net] *On Behalf Of *Nick Griffin
> *Sent:* Tuesday, June 03, 2008 4:12 PM
>
> *To:* David Toledo
> *Cc:* cisco-voip at puck.nether.net
> *Subject:* Re: [cisco-voip] CISCO 2851
>
>
>
> Please toss us what your requirements are and we could provide a solution.
>
> On Tue, Jun 3, 2008 at 3:08 PM, David Toledo <DavidT at morganmint.com>
> wrote:
>
> I got it to work with the command bellow
>
>
>
> But now when type the command: *show snmp*
>
> * *
>
> *It show that the: "SNMP logging: disabled"*
>
> * *
>
> *Why is that*
>
> * *
>
> *Thanks*
>
> * *
>
> *David*
>
>
>
>
>  ------------------------------
>
> *From:* cisco-voip-bounces at puck.nether.net [mailto:
> cisco-voip-bounces at puck.nether.net] *On Behalf Of *Mordechai
> *Sent:* Tuesday, June 03, 2008 3:48 PM
> *To:* David Toledo; cisco-voip at puck.nether.net
>
>
> *Subject:* Re: [cisco-voip] CISCO 2851
>
>
>
> Where is the ^ marker stuck? If under ro than try upper case RO. Otherwise
> the syntax is correct:
>
>
>
> *snmp-server community kh0vr0 RO 50*
>
>
>
>
>  ------------------------------
>
> *From:* cisco-voip-bounces at puck.nether.net [mailto:
> cisco-voip-bounces at puck.nether.net] *On Behalf Of *David Toledo
> *Sent:* Tuesday, June 03, 2008 3:36 PM
> *To:* cisco-voip at puck.nether.net
> *Subject:* Re: [cisco-voip] CISCO 2851
>
>
>
> *Sorry guys I'm not familiar with the command very well*
>
> *I enable but not sure if woulf runn this command bellow*
>
> * *
>
> *snmp-server community kh0vr0 ro 50 ???*
>
> * *
>
> *! Create SNMP communities and username*
>
> !access-list 50 permit host xxxxxxxxxx
>
>
>
> !snmp-server community kh0vrw RW 50
>
> !snmp-server community kh0vr0 RO 50
>
> !snmp-server system-shutdown
>
> !username %%%% password xxxxxxx
>
>
>
>
>
> Thanks
>
>
>
> David
>
>
>
>
>
>
>  ------------------------------
>
> *From:* cisco-voip-bounces at puck.nether.net [mailto:
> cisco-voip-bounces at puck.nether.net] *On Behalf Of *Nick Griffin
> *Sent:* Tuesday, June 03, 2008 3:25 PM
> *To:* David Toledo
> *Cc:* cisco-voip at puck.nether.net
> *Subject:* Re: [cisco-voip] CISCO 2851
>
>
>
> have you enabled "enable" and entered config mode " conf t"
>
>
>
>
>
>
>
> On Tue, Jun 3, 2008 at 2:22 PM, David Toledo <DavidT at morganmint.com>
> wrote:
>
> I try to enable my snmp on cisco 2851 I got this error
>
>
>
>
>
> % Invalid input detected at '^' marker.
>
>
>  ------------------------------
>
> *From:* cisco-voip-bounces at puck.nether.net [mailto:
> cisco-voip-bounces at puck.nether.net] *On Behalf Of *Nick Griffin
> *Sent:* Tuesday, June 03, 2008 3:09 PM
> *To:* David Toledo
> *Cc:* cisco-voip at puck.nether.net
> *Subject:* Re: [cisco-voip] CISCO 2851
>
>
>
> snmp-server community BLAH
>
> On Tue, Jun 3, 2008 at 2:06 PM, David Toledo <DavidT at morganmint.com>
> wrote:
>
> Does any one know how to enable snmp for the cisco 2851 router
>
>
>
> Thanks
>
>
>
>
>
> David
>
>
> _______________________________________________
> cisco-voip mailing list
> cisco-voip at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-voip
>
>
>
>
> _______________________________________________
> cisco-voip mailing list
> cisco-voip at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-voip
>
>
>
>
>
> No virus found in this incoming message.
> Checked by AVG.
> Version: 7.5.524 / Virus Database: 269.24.6/1480 - Release Date: 6/3/2008
> 7:00 AM
>
>
>
> No virus found in this outgoing message.
> Checked by AVG.
> Version: 7.5.524 / Virus Database: 269.24.6/1480 - Release Date: 6/3/2008
> 7:00 AM
>
>
> _______________________________________________
> cisco-voip mailing list
> cisco-voip at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-voip
>
>
>
> _______________________________________________
> cisco-voip mailing list
> cisco-voip at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-voip
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://puck.nether.net/pipermail/cisco-voip/attachments/20080603/fed1d804/attachment.html>