[c-nsp] Bus error when going to 12.2.26

[Rodney Dunn]

This crash was in the boot image it looks like
because the 'sh ver' says:

> >> lone-ds3-hub1 uptime is 2 days, 7 hours, 20 minutes
> >> System returned to ROM by reload at 07:03:29 UTC Wed Nov 3 2004
> >> System restarted at 07:05:06 UTC Wed Nov 3 2004

Notice on bootup it decompresses two images.
a) the boot
then
b) the full IOS image

What boot image do you have in bootflash?

Can you confirm that it did boot up normally after the
crash loading the boot image?

Rodney




On Fri, Nov 05, 2004 at 02:47:57PM -0600, Brian Feeny wrote:
> 
> We upgraded a 7206/NPE-150 that is mostly handling a bunch of CT3's  
> from 12.2.19 to 12.2.26
> and saw a bus error on reboot.  Its up and working, but I was concerned  
> about the error and if anyone
> could shed some light on what may be wrong.
> 
> Brian
> 
> 
> >>
> >> -- System Bootstrap, Version 11.1(10) [dschwart 10], RELEASE SOFTWARE  
> >>  (fc1)
> >> Copyright (c) 1994 by cisco Systems, Inc.
> >> C7200 processor with 131072 Kbytes of main memory
> >>
> >>
> >> Self decompressing the image :   
> >> #################################################
> >> ###################################################################### 
> >> # #########
> >> ###################################################################### 
> >> # #########
> >> ################################################# [OK]
> >>
> >> %C7200-3-PACONFIG: Exceeds 3 high speed port adaptors
> >> %CT3-1-INITFAIL: Slot 4 firmware init (ct3sw_pci_init (count !=   
> >> expected_count))
> >> %PA-3-DEACTIVATED: port adapter in bay [4] powered off.
> >> %SYS-4-CONFIG_NEWER: Configuration from version 12.2 may not be   
> >> correctly unders
> >> tood
> >> %CONTROLLER-5-UPDOWN: Controller T3 1/0, changed state to up
> >> %CONTROLLER-5-UPDOWN: Controller T3 2/0, changed state to up
> >> %ALIGN-1-FATAL: Illegal access to a low address
> >>  addr=0x0, pc=0x60274888, ra=0x60274B7C, sp=0x6090C3A0
> >>
> >>
> >> === Flushing messages (07:04:15 UTC Wed Nov 3 2004) ===
> >>
> >> *** System received a Bus Error exception ***
> >> signal= 0xa, code= 0x40c, context= 0x6081ba20
> >> PC = 0x6033c890, Cause = 0x2420, Status Reg = 0x34008002
> >>
> >> System Bootstrap, Version 11.1(10) [dschwart 10], RELEASE SOFTWARE   
> >> (fc1)
> >> Copyright (c) 1994 by cisco Systems, Inc.
> >> C7200 processor with 131072 Kbytes of main memory
> >>
> >>
> >> Self decompressing the image :   
> >> #################################################
> >> ############################################################# [OK]
> >>
> >>               Restricted Rights Legend
> >>
> >> Use, duplication, or disclosure by the Government is
> >> subject to restrictions as set forth in subparagraph
> >> (c) of the Commercial Computer Software - Restricted
> >> Rights clause at FAR sec. 52.227-19 and subparagraph
> >> (c) (1) (ii) of the Rights in Technical Data and Computer
> >> Software clause at DFARS sec. 252.227-7013.
> >>
> >>            cisco Systems, Inc.
> >>            170 West Tasman Drive
> >>            San Jose, California 95134-1706
> >>
> >> ------------------
> >>
> >> lone-ds3-hub1#sh ver
> >> Cisco Internetwork Operating System Software
> >> IOS (tm) 7200 Software (C7200-P-M), Version 12.2(26), RELEASE  
> >> SOFTWARE  (fc2)
> >> Copyright (c) 1986-2004 by cisco Systems, Inc.
> >> Compiled Sat 31-Jul-04 01:26 by eaarmas
> >> Image text-base: 0x60008940, data-base: 0x610E8000
> >>
> >> ROM: System Bootstrap, Version 11.1(10) [dschwart 10], RELEASE   
> >> SOFTWARE (fc1)
> >>
> >> lone-ds3-hub1 uptime is 2 days, 7 hours, 20 minutes
> >> System returned to ROM by reload at 07:03:29 UTC Wed Nov 3 2004
> >> System restarted at 07:05:06 UTC Wed Nov 3 2004
> >> System image file is "slot0:c7200-p-mz.122-26.bin"
> >>
> >> cisco 7206 (NPE150) processor (revision B) with 114688K/16384K bytes   
> >> of memory.
> >> Processor board ID 16072082
> >> R4700 CPU at 150Mhz, Implementation 33, Rev 1.0, 512KB L2 Cache
> >> 6 slot midplane, Version 1.3
> >>
> >> Last reset from power-on
> >> X.25 software, Version 3.0.0.
> >> Bridging software.
> >> Primary Rate ISDN software, Version 1.1.
> >>
> >> Number of Fast PAs = 4
> >> Number of Fast+Medium PAs = 4
> >> Total number of PA bandwidth points consumed = 560
> >> Please refer to the following document "Cisco 7200 Series Port  
> >> Adaptor  Hardware Configuration Guidelines" on CCO <www.cisco.com>,  
> >> for c7200  bandwidth points oversubscription/usage guidelines.
> >> WARNING: Number of Fast PAs Exceeds 3
> >>
> >> 1 FastEthernet/IEEE 802.3 interface(s)
> >> 87 Serial network interface(s)
> >> 4 Channelized T3 port(s)
> >> 125K bytes of non-volatile configuration memory.
> >> 1024K bytes of packet SRAM memory.
> >>
> >> 20480K bytes of Flash PCMCIA card at slot 0 (Sector size 128K).
> >> 46976K bytes of ATA PCMCIA card at slot 1 (Sector size 512 bytes).
> >> 4096K bytes of Flash internal SIMM (Sector size 256K).
> >> Configuration register is 0x2102
> >>
> >> --------
> >>
> >> Ser1/0 - PA-MC-T3
> >> Ser2/0 - PA-MC-T3
> >> Ser4/0 and 4/1 - PA-MC-2T3
> >> Fa5/0 - PA-FE-TX
> >>
> 
> ------------------------------------------------------------------------ 
> ------
> Brian Feeny, CCIE #8036, CISSP    	e: signal at shreve.net
> Network Engineer           			p: 318.213.4709
> ShreveNet Inc.             			f: 318.221.6612



> _______________________________________________
> cisco-nsp mailing list  cisco-nsp at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-nsp
> archive at http://puck.nether.net/pipermail/cisco-nsp/