[c-nsp] Catalyst 4506 won't boot!?

[MADMAN]

   First thing I would try is pull all card minus the sup and see if it 
comes up.  If it does add one at a time.

   Dave

Xavier Mertens wrote:

> After a looooong time, I got:
> 
>  0: F  1: F  2: F  3: F  4: F  5: F  6: F  7: F  8: F  9: F 10: F 11: F
>  12: F 13: F 14: F 15: F 16: F 17: F 18: F 19: F 20: F 21: F 22: F 23: F
>  24: F 25: F 26: F 27: F 28: F 29: F 30: F 31: F
> 
> Port Traffic: L2 Asic Loopback ...
> 
> Xavier
> --
> The best things in life are free, but the expensive ones are still worth a look.
> 
> On Tue, 8 Feb 2005, Xavier wrote:
> 
> 
>>Hi,
>>
>>I just mounted a brand new Catalyst 4506 with the following modules:
>>
>>Slot1: ws-x4013+=
>>Slot2: ws-x4448-gb-rj45=
>>Slot3: ws-x4306-gb=
>>Slot4: ws-x4306-gb=
>>
>>Here are the messages on console:
>>
>> **********************************************************
>> *                                                        *
>> * Welcome to Rom Monitor for WS-X4013+ System.           *
>> * Copyright (c) 1999-2003 by Cisco Systems, Inc.         *
>> * All rights reserved.                                   *
>> *                                                        *
>> **********************************************************
>>
>> Rom Monitor Program Version 12.1(20r)EW1
>> Supervisor: WS-X4013+  Chassis: WS-C4506
>> Hardware Revisions - Board: 5.4 CPLD: 3 Dagobah: 90
>>
>>
>> MAC Address  : 00-0e-83-5a-95-29
>> Ip Address   : Not set.
>> Netmask      : Not set.
>> Gateway      : Not set.
>> TftpServer   : Not set.
>> Main Memory  : 256 MBytes
>>
>>
>>
>> ***** The system will autoboot in 5 seconds *****
>>
>>
>> Type control-C to prevent autobooting.
>> . . . . .
>>
>> ******** The system will autoboot now ********
>>
>>
>> config-register = 0x2101
>>
>> Autobooting using the first file from bootflash.....
>>
>>
>>Rommon reg: 0x5A004180
>>
>>Running diags...
>>
>>Decompressing the image
>>########################## [OK]
>>
>>k2diags version 2.4.2
>>
>>prod: WS-X4013+  part: 73-9447-02  serial: JAE0840XJPY
>>
>>
>>Power-on-self-test for Module 1:  WS-X4013+
>> Port/Test Status: (. = Pass, F = Fail)
>> Reset Reason: PowerUp
>>
>>
>>Port Traffic: L2 Serdes Loopback ...
>>
>>And nothing more! Status LEDs are red on all modules!
>>Any suggestion?
>>
>>Xavier
>>--
>>"Research is what I'm doing when I don't know what I'm doing."
>>- Wernher Von Braun (1912-1977) 
>>_______________________________________________
>>cisco-nsp mailing list  cisco-nsp at puck.nether.net
>>https://puck.nether.net/mailman/listinfo/cisco-nsp
>>archive at http://puck.nether.net/pipermail/cisco-nsp/
>>
> 
> _______________________________________________
> cisco-nsp mailing list  cisco-nsp at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-nsp
> archive at http://puck.nether.net/pipermail/cisco-nsp/
> 

-- 
David Madland
CCIE# 2016
Sr. Network Engineer
Qwest Communications
612-664-3367

"Emotion should reflect reason not guide it"