[c-nsp] RPR+ on Cisco 7513

[Rodney Dunn]

Dan,

Can you poste a 'sh redund' before
you force the switchover?

Also, post a 'sh diag' and a
'sh ver' from both RSP's.

and the configuration.

Rodney

On Tue, Jan 25, 2005 at 10:19:47AM -0500, Dan Benson wrote:
> Thank you all for your feed back on RPR.  At this point, I have loaded 
> the code suggested by many, 12.0(27)S4, running SSO, not RPR and I am 
> still not able to get this working.  When I force the switch over from 
> one RSP to the other, I get this error on the new Master RSP:
> 
> 
> 00:02:48: %HA-5-MODE: Operating mode is hsa, configured mode is sso.
> 00:02:48: %HA-2-CUTOVER_NOTICE: Cutover initiated. Cease all console 
> activity until system restarts.
> 00:02:48: %HA-2-CUTOVER_NOTICE: Do not add/remove RSPs or line cards 
> until switchover completes.
> 00:02:48: %HA-2-CUTOVER_NOTICE: Deinitializing subsystems...
> 00:02:48: %OIR-6-REMCARD: Card removed from slot 0, interfaces disabled
> 00:02:48: %OIR-6-REMCARD: Card removed from slot 1, interfaces disabled
> 00:02:48: %OIR-6-REMCARD: Card removed from slot 2, interfaces disabled
> 00:02:48: %OIR-6-REMCARD: Card removed from slot 3, interfaces disabled
> 00:02:48: %OIR-6-REMCARD: Card removed from slot 4, interfaces disabled
> 00:02:48: %HA-2-CUTOVER_NOTICE: Reinitializing subsystems...
> 00:02:49: %CBUS-3-CMDTIMEOUT: Cmd timed out, CCB 0xF800FF20, slot 0, cmd 
> code 0
> -Traceback= 4045F704 40460A08 40458C20 4045D70C 4045DDDC 404544DC 
> 40143F58 401C35C8 40143A08 40393BC4 40393BB0
> 00:02:49: %CBUS-3-CMDTIMEOUT: Cmd timed out, CCB 0xF800FF30, slot 1, cmd 
> code 0
> -Traceback= 4045F704 40460A08 40458C20 4045D70C 4045DDDC 404544DC 
> 40143F58 401C35C8 40143A08 40393BC4 40393BB0
> 00:02:50: %CBUS-3-CMDTIMEOUT: Cmd timed out, CCB 0xF800FF40, slot 2, cmd 
> code 0
> -Traceback= 4045F704 40460A08 40458C20 4045D70C 4045DDDC 404544DC 
> 40143F58 401C35C8 40143A08 40393BC4 40393BB0
> 00:02:50: %CBUS-3-CMDTIMEOUT: Cmd timed out, CCB 0xF800FF50, slot 3, cmd 
> code 0
> -Traceback= 4045F704 40460A08 40458C20 4045D70C 4045DDDC 404544DC 
> 40143F58 401C35C8 40143A08 40393BC4 40393BB0
> 00:02:50: %RSP-3-SLAVECHANGE: Slave changed state from Non-participant 
> to Slave
> 00:02:50: %CBUS-3-CMDTIMEOUT: Cmd timed out, CCB 0xF800FF60, slot 4, cmd 
> code 0
> -Traceback= 4045F704 40460A08 40458C20 4045D70C 4045DDDC 404544DC 
> 40143F58 401C35C8 40143A08 40393BC4 40393BB0
> 00:02:50: %HA-2-CUTOVER_NOTICE: System preparing to restart...
> 00:02:50: %HA-5-NOTICE: Resuming initialization...
> 00:02:50: %HA-2-CUTOVER_NOTICE: Cutover completed and system restarted.
> 00:02:50: %HA-2-CUTOVER_NOTICE: You may add/remove RSPs and line cards 
> after interfaces are fully operational.
> 00:02:50: %HA-5-NOTICE: Standby (slave) will be restarted in 
> approximately 5 minutes.
> 
> At this point, the system again does not see any of the VIPs in the 
> chassie and therefore the router is dead to me.  This is in a Lab, and I 
> look forward to all your help.  Thanks Much.. //db