[c-nsp] 1721 Service module configuration

[goutam at infovision21.com]

I did the following  and its fails the selftest.
Not sure if there are any ??

#test service-module serial 0
Failed to perform service-module selftest


> 
> From: "Dan Martin" <dmartin at micromuse.com>
> Date: 2005/05/22 Sun PM 01:53:33 EDT
> To: <goutam at infovision21.com>
> Subject: RE: RE: [c-nsp] 1721 Service module configuration
> 
> The straight through should be fine.
> 
> It would be easier to say the problem was the wic but it looks like the
> wic is passing post.  
> 
> Is there some kind of enhanced debug you can turn on so you can verify
> the wic is indeed coming up with no complaints?
> 
> I even think there is some kind of hardware test command you can issue,
> isn't there?
> 
> -----Original Message-----
> From: goutam at infovision21.com [mailto:goutam at infovision21.com] 
> Sent: Sunday, May 22, 2005 11:09 AM
> To: Dan Martin
> Subject: Re: RE: [c-nsp] 1721 Service module configuration
> 
> Thanks Dan,
> Do i have to use an RJ48 or can i use RJ45 straight thru
> The person who installed T1 tested with RJ45..(i called him to confirm
> this) but cisco docs say RJ48
> 
> Is it possible that the WIC DSU/CSU is bad ??
> 
> Thanks a lot again
> - Goutam
> 
> 
> > 
> > From: "Dan Martin" <dmartin at micromuse.com>
> > Date: 2005/05/22 Sun AM 10:55:22 EDT
> > To: <goutam at infovision21.com>
> > Subject: RE: [c-nsp] 1721 Service module configuration
> > 
> > Of no particular assistance;
> > 
> > Its actually rj48, the T1 uses wires 1,2 and 4,5
> > Ethernet uses 1,2 and 3,6
> > 
> > If your patch cable is straight through, its moot, although it still
> > doesn't explain why the module is "locking".
> > 
> > -----Original Message-----
> > From: cisco-nsp-bounces at puck.nether.net
> > [mailto:cisco-nsp-bounces at puck.nether.net] On Behalf Of
> > goutam at infovision21.com
> > Sent: Sunday, May 22, 2005 10:44 AM
> > To: cisco-nsp at puck.nether.net
> > Subject: [c-nsp] 1721 Service module configuration
> > 
> > Hello,
> > 
> > I have a new cisco router 1721 and was trying to configure T1.
> > inserted the WIC DSU/CSU card. I configured the fast ethernet port for
> > remote access. (Iam using a RJ 45 to connect from Smart jack to
> DSU/CSU
> > My command list is as follows
> > 
> > #config t
> > #interface serial 0
> > #service-module t1 framing esf
> > %Service module configuration command failed: LOCK OBTAIN TIMEOUT.
> > 
> > I get the error as described in last line .. 
> > Service module configuration command failed: LOCK OBTAIN TIMEOUT.
> > 
> > I tried clearing out the using "clear service-module serial 0"
> > 
> > No clue on how to proceed ?
> > 
> > Any help is appreciated.
> > goutam
> > 
> > 
> > 
> > 
> > _______________________________________________
> > cisco-nsp mailing list  cisco-nsp at puck.nether.net
> > https://puck.nether.net/mailman/listinfo/cisco-nsp
> > archive at http://puck.nether.net/pipermail/cisco-nsp/
> > 
> > 
> 
> 
>