[c-nsp] Really need help with atm vc-per-vp on NM-4T1 3640

[Jason Philbrook]

On my 3640, I have to re-enter the command at each boot for the 
interfaces because it won't save in the startup config.

dsl-atm.a10.dc(config)#int atm1/0
dsl-atm.a10.dc(config-if)#atm vc-per-vp 1024
dsl-atm.a10.dc(config-if)#^Z
dsl-atm.a10.dc(config)#int atm1/1
dsl-atm.a10.dc(config-if)#atm vc-per-vp 1024
dsl-atm.a10.dc(config-if)#^Z

Then I have to reenter customer's configs. 12.1(5)T15 is what I am 
running.

On Fri, Feb 03, 2006 at 08:47:44AM -0800, Ruben Alvarez wrote:
> Anyone else?  The bug was early in 12.2.  It's not related to the bug.
> Also, I can't remove the command either.  I try a "no atm vc-per-vp 1024."
> It behaves like to accepted the command, but it still shows up when I do a
> "sh int."  
> 
> -----Original Message-----
> From: Brian Turnbow [mailto:b.turnbow at twt.it] 
> Sent: Friday, February 03, 2006 2:51 AM
> To: Ruben Alvarez; cisco-nsp at puck.nether.net
> Subject: RE: [c-nsp] Really need help with atm vc-per-vp on NM-4T1 3640
> 
> Basically this command robs bits from the vp side to use in the vc side.
> It limits teh vps you can then use ie 512 only allows you to have vp values
> 0-15 64-79 
> There was a bug related to this command that was resolved somewhere in 12.2,
> but I don't remrember when.
> 
> Brian
> 
> -----Original Message-----
> From: cisco-nsp-bounces at puck.nether.net
> [mailto:cisco-nsp-bounces at puck.nether.net] On Behalf Of Ruben Alvarez
> Sent: venerdì 3 febbraio 2006 2.06
> To: cisco-nsp at puck.nether.net
> Subject: [c-nsp] Really need help with atm vc-per-vp on NM-4T1 3640
> 
> All.
> 
> I'm having a really hard time getting this command to work.  As I
> understand, I should be able to adjust the number of maximum active VCs that
> module will allow.  Currently, it is allowing 255 maximum VCs.  I'm using
> IOS 12.2(32) GD.
> 
> I'll shut all 4 of the interfaces and apply the command.  It looks like the
> command is applied, but the value for maximum active VCs does not change.
> If I do a show interface, I see that the command is in the interface,
> vc-per-vp 512.
> 
> There's not much documentation of this command.  Anyone have any experience
> with this?
> 
> Thanks
> Ruben Alvarez
> Opus:interactive
> 
> 
> 
> _______________________________________________
> cisco-nsp mailing list  cisco-nsp at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-nsp
> archive at http://puck.nether.net/pipermail/cisco-nsp/
> 
> 
> _______________________________________________
> cisco-nsp mailing list  cisco-nsp at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-nsp
> archive at http://puck.nether.net/pipermail/cisco-nsp/

-- 
/*
Jason Philbrook   |   Midcoast Internet Solutions - Internet Access,
    KB1IOJ        |  Hosting, and TCP-IP Networks for Midcoast Maine
 http://f64.nu/   |             http://www.midcoast.com/
*/