[c-nsp] Channelized E1/PRI Problem

[Jarrod Friedland (DHL AU)]

Peter

You may want to start with this

http://www.cisco.com/warp/public/116/show_ce1.html

I think you will find what you are after on this page or off one of the
links at the bottom

 
 
 
--
Kind Regards
Jarrod Friedland
Communications Analyst Oceania
------------------------------------------------------------------------
------------------
D H L
 
P: +61 7 3845 7735 * M: +61 401 500 134 * F: +61 7 3825 7979
E-mail: jarrod.friedland at dhl.com * www: http://www.dhl.com/
10 Boronia Road Eagle Farm Queensland 4009
 
 

> -----Original Message-----
> From: cisco-nsp-bounces at puck.nether.net [mailto:cisco-nsp-
> bounces at puck.nether.net] On Behalf Of Peter Nyamukusa
> Sent: Thursday, 17 May 2007 3:24 AM
> To: cisco-nsp at puck.nether.net
> Subject: [c-nsp] Channelized E1/PRI Problem
> 
> Hi Folks,
> 
> 
> 
> I have just installed a Channelized E1/PRI card on my 3725 router and
I am
> getting a local alarm from the E1 card could it be possible that the
> Chassis
> is not compatible to the card. I have pasted the show version & show
> controllers from my router, any help is appreciated in pointing me in
the
> right direction
> 
> 
> 
> System image file is "slot0:c3725-is-mz.123-13a.bin"
> 
> 
> 
> cisco 3725 (R7000) processor (revision 0.1) with 245760K/16384K bytes
of
> memory.
> 
> Processor board ID FCZ09487019
> 
> R7000 CPU at 240MHz, Implementation 39, Rev 3.3, 256KB L2 Cache
> 
> Channelized E1, Version 1.0.
> 
> Bridging software.
> 
> X.25 software, Version 3.0.0.
> 
> SuperLAT software (copyright 1990 by Meridian Technology Corp).
> 
> Primary Rate ISDN software, Version 1.1.
> 
> 2 FastEthernet/IEEE 802.3 interface(s)
> 
> 8 Low-speed serial(sync/async) network interface(s)
> 
> 2 Channelized E1/PRI port(s)
> 
> DRAM configuration is 64 bits wide with parity disabled.
> 
> 55K bytes of non-volatile configuration memory.
> 
> 31360K bytes of ATA System CompactFlash (Read/Write)
> 
> 62720K bytes of ATA Slot0 CompactFlash (Read/Write)
> 
> 
> 
> 
> 
> show controllers e1 2/0
> 
> E1 2/0 is down.
> 
>   Applique type is Channelized E1 - balanced
> 
>   Transmitter is sending remote alarm.
> 
>   Receiver has loss of signal.
> 
>   alarm-trigger is not set
> 
>   Framing is CRC4, Line Code is HDB3, Clock Source is Line.
> 
>   Data in current interval (323 seconds elapsed):
> 
>      0 Line Code Violations, 0 Path Code Violations
> 
>      0 Slip Secs, 323 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
> 
>      0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 323
Unavail
> Secs
> 
>   Data in Interval 1:
> 
>      0 Line Code Violations, 0 Path Code Violations
> 
>      0 Slip Secs, 900 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
> 
>      0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 900
Unavail
> Secs
> 
> 
> 
> Peter
> 
> 
> 
> _______________________________________________
> cisco-nsp mailing list  cisco-nsp at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-nsp
> archive at http://puck.nether.net/pipermail/cisco-nsp/