Duplex problems typically show runt, crc and collisions.
The show interface line with:
Full-duplex, Unknown Speed, 100BaseTX/FX
might be the problem.
How about :
interface FastEthernet1/0
ip address *.*.*.* *.*.*.*
load-interval 30
speed 100
duplex full
end
and check the config on the 3560
int fa1/2
speed 100
duplex full
switchport
switchport mode access
spanning-tree portfast
If you are paranoid with portfast, add "spanning-tree bpduguard enable"
----
Matthew Huff | One Manhattanville Rd
OTA Management LLC | Purchase, NY 10577
http://www.ox.com | Phone: 914-460-4039
aim: matthewbhuff | Fax: 914-460-4139
-----Original Message-----
From: cisco-nsp-bounces at puck.nether.net [mailto:cisco-nsp-bounces at puck.nether.net] On Behalf Of Elmar K. Bins
Sent: Monday, June 08, 2009 5:03 PM
To: cisco-nsp at puck.nether.net
Subject: [c-nsp] ASR7401 and PA-FE-TX (ISL)
Re folks,
my private 7401 felt a bit empty, and I bought an ISL for it
(this should be the mgt interface, not much bandwidth).
I wonder if it is broken, or if I am doing something wrong, or
if this just cannot work because I'm too st00p1d and bought the
wrong thing...
The "show interface" output is quite interesting. No input packets,
but hundreds of thousands of input errors _per second_:
==========================================================================
rt#sh int f1/0
FastEthernet1/0 is up, line protocol is up
Hardware is DEC21140A, address is 000a.4230.841c (bia 000a.4230.841c)
Internet address is *.*.*.*
MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
reliability 245/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full-duplex, Unknown Speed, 100BaseTX/FX
ARP type: ARPA, ARP Timeout 04:00:00
Last input never, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
30 second input rate 0 bits/sec, 0 packets/sec
30 second output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
2770584934 input errors, 0 CRC, 0 frame, 42604211 overrun, 2727980723 ignored
0 watchdog
0 input packets with dribble condition detected
2432 packets output, 242733 bytes, 0 underruns
0 output errors, 0 collisions, 2090 interface resets
0 babbles, 0 late collision, 0 deferred
2078 lost carrier, 0 no carrier
0 output buffer failures, 0 output buffers swapped out
==========================================================================
Needless to say, I cannot see anything there and I cannot ping the
address with a direct connection either...
Config is straightforward:
interface FastEthernet1/0
ip address *.*.*.* *.*.*.*
load-interval 30
duplex full
end
(I explicitly set the media-type, but that was obviously alright)
Of course the switch (3560) the box is connected to has full-duplex
configured on the if.
Any ideas?
Elmar.
_______________________________________________
cisco-nsp mailing list cisco-nsp at puck.nether.net
https://puck.nether.net/mailman/listinfo/cisco-nsp
archive at http://puck.nether.net/pipermail/cisco-nsp/