[c-nsp] Cisco CISCO7606-S Module

[Mohammad Khalil]

hi Arie

we made the hard reset and the logs still appear so TAC informed us that the module is faulty and we ordered a new one
Thanks a lot for your help

Regards,
Mohammad Khalil

> Subject: RE: [c-nsp] Cisco CISCO7606-S Module
> Date: Sun, 22 Aug 2010 15:37:16 +0200
> From: avayner at cisco.com
> To: eng_mssk at hotmail.com; cisco-nsp at puck.nether.net
> 
> Mohammad,
> 
> This could be (after a very quick query) related to CSCef46923 "Group of
> 4 ports on WS-X6516-xx modules may stop forwarding traffic"
> 
> These are the release notes:
> PROBLEM/SYMPTOMS
> ================
> Under very rare conditions, a group of ports on the same port-ASIC may
> experience connectivity issue. This issue can occur on any module which
> uses the same port-ASIC as WS-X6516-GE-TX.
> 
> The following syslog messages might also be seen, but is not required to
> observe the issue.
> 
> %PM_SCP-SP-6-LCP_FW_ERR_INFORM: Module 4 is experiencing the following
> error:
> Pinnacle #0, Frames with Bad Packet CRC Error (PI_CI_S_PKTCRC_ERR -
> 0xC7) = 
> 110
> 
> 
> Syslog Messages update  (3/14/05)
> ==========================================
> 
> Examples of Syslog message from IOS:
> ______________________________________________________________
> %PM_SCP-SP-2-LCP_FW_ERR_INFORM: Module 5 is experiencing the following
> error:
> PINNACLE Pb transient parity error detected : ports - 1 3 5 7
> 
> %PM_SCP-SP-2-LCP_FW_ERR_INFORM: Module 5 is experiencing the following
> error:
> Bus Asic #1 transient Pb error.  Recovered. (0x1234, 0x5678)
> 
> 
> Examples of Syslog message from CatOS:
> ______________________________________________________________
>  
> %SYS-3-PKTBUFFERFAIL_ERRDIS:Packet buffer failure detected.
> Err-disabling 
> port 5/5.
>  
> %SYS-3-PKTBUFFERFAIL_PWRCYCLE:Packet buffer failure detected. Power
> cycling
> module 5.
>  
> ______________________________________________________________
> 
> Condition
> =========
> The problem usually happens to a group of ports that are connected 
> through the same ASIC.
>   
> WORKAROUND
> ==========
> The problem will usually recover after hard-reset the module.  If the
> problem
> keeps happening on the same module, please contact TAC.
> 
> 
> 
> 
> 
> 
> So, I would suggest you contact TAC for this...
> Arie
> 
> -----Original Message-----
> From: cisco-nsp-bounces at puck.nether.net
> [mailto:cisco-nsp-bounces at puck.nether.net] On Behalf Of Mohammad Khalil
> Sent: Sunday, August 22, 2010 10:26
> To: cisco-nsp at puck.nether.net
> Subject: [c-nsp] Cisco CISCO7606-S Module
> 
> 
> 
> 
> We
> are facing some issues with our Cisco CISCO7606-S on the
> module SFM-capable 48 port 10/100/1000mb RJ45 (Model Number
> WS-X6548-GE-TX) 
> please see the log below:Aug 21 03:53:18.275 EET:
> %PM_SCP-SP-2-LCP_FW_ERR_INFORM: Module 3 is experiencing the following
> error: Bus Asic #0 transient Pb error.  Recovered (0x0000, 0x0042) 
> Aug 21 03:53:31.327 EET: %PM_SCP-SP-2-LCP_FW_ERR_INFORM: Module 3 is
> experiencing the following error: Bus Asic #0 transient Pb error.
> Recovered (0x0000, 0x0042) 
> Aug 21 03:53:44.579 EET: %PM_SCP-SP-2-LCP_FW_ERR_INFORM: Module 3 is
> experiencing the following error: Bus Asic #0 transient Pb error.
> Recovered (0x0000, 0x0046) 
> Aug 21 03:53:57.631 EET: %PM_SCP-SP-2-LCP_FW_ERR_INFORM: Module 3 is
> experiencing the following error: Bus Asic #0 transient Pb error.
> Recovered (0x0000, 0x0042) 
> Aug 21 03:54:11.392 EET: %PM_SCP-SP-2-LCP_FW_ERR_INFORM: Module 3 is
> experiencing the following error: Bus Asic #0 transient Pb error.
> Recovered (0x0000, 0x0042)
> any ideas ?  
> 
> Thanks in advance
> Best Regards,
> 
> 
> 
>  		 	   		  
> _______________________________________________
> cisco-nsp mailing list  cisco-nsp at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-nsp
> archive at http://puck.nether.net/pipermail/cisco-nsp/