[c-nsp] DFC3C-XL refuses to operate in XL mode
Dimitris Befas
dimitris.befas at gmail.com
Wed Jul 30 06:13:50 EDT 2014
You cannot get an PFC3CXL mode when combining CFC and PFC sub-modules. The
PFC capability is per module, but the PFC mode is a chassis function.
For your specific hardware config, you will accomplish a PFC3CXL mode only
if you remove slots 3 and 5 or if you replace their sub-modules with
DFC3CXL.
Dimitris
On Jul 30, 2014 12:39 PM, "Jiri Prochazka" <jiri.prochazka at superhosting.cz>
wrote:
> Hi,
>
> I am building a new 7606S chassis, with RSP720-3CXL (12.2(33)SRE10) and a
> few X6704-10GE linecards.
>
> Most of 6704-10GE cards are equipped with DFC3C-XL modules.
>
> The problem is that two DFC3C-XL modules are unwilling to operate in 3C-XL
> mode. Both DFC's are from different sources, so I highly doubt both are
> faulty the same way.
>
> But both show the same symptoms. Although they are 3C-XL versions, they
> work as 3C only..which degrades PFC operating mode of the whole chassis to
> PFC3C. As soon as I swap DFC on respective 6704 card to some other piece,
> it works OK.
>
> What confuses me the most is this log record ->
>
> *Feb 25 02:15:11.324: %OIR-SP-6-DOWNGRADE_EARL: Module 6 PFC installed is
> not identical to system PFC and will perform at current system operating
> mode.
>
>
> WS-X6704-10GE with WS-F6700-DFC3CXL is in the SLOT 4. RSP720-3CXL-GE with
> 7600-PFC3CXL is in the SLOT 6.
>
> Why is the switch complaining that PFC in slot6 (Supervisor) is not
> identical to system PFC (Supervisor?)?
>
>
> 7606S-lab#show module
> Mod Ports Card Type Model Serial No.
> --- ----- -------------------------------------- ------------------
> -----------
> 1 4 CEF720 4 port 10-Gigabit Ethernet WS-X6704-10GE SAL1552ZWUQ
> 2 4 CEF720 4 port 10-Gigabit Ethernet WS-X6704-10GE SAL1545UJY7
> 3 4 CEF720 4 port 10-Gigabit Ethernet WS-X6704-10GE SAL1234173T
> 4 4 CEF720 4 port 10-Gigabit Ethernet WS-X6704-10GE SAL16020J6H
> 5 48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX SAL10019Q21
> 6 2 Route Switch Processor 720 (Active) RSP720-3CXL-GE SAL1538QMQX
>
> Mod MAC addresses Hw Fw Sw Status
> --- ---------------------------------- ------ ------------ ------------
> -------
> 1 0011.934a.001c to 0011.934a.001f 1.5 Unknown Unknown PwrDown
> 2 0011.9370.270c to 0011.9370.270f 1.5 Unknown Unknown PwrDown
> 3 0022.902b.fc44 to 0022.902b.fc47 2.7 Unknown Unknown PwrDown
> 4 0011.204f.ff68 to 0011.204f.ff6b 1.5 12.2(18r)S1 12.2(33)SRE1 Ok
> 5 0016.9dcb.6434 to 0016.9dcb.6463 2.9 Unknown Unknown PwrDown
> 6 001c.584c.ab98 to 001c.584c.ab9b 5.9 12.2(33r)SRE 12.2(33)SRE1 Ok
>
> Mod Sub-Module Model Serial Hw Status
> ---- --------------------------- ------------------ ----------- -------
> -------
> 1 Distributed Forwarding Card WS-F6700-DFC3CXL SAL1423K3UR 1.6
> PwrDown
> 2 Distributed Forwarding Card WS-F6700-DFC3CXL SAL160101ZB 1.7
> PwrDown
> 3 Centralized Forwarding Card WS-F6700-CFC SAL12330HQ6 4.1
> PwrDown
> 4 Distributed Forwarding Card WS-F6700-DFC3CXL SAL1406AMHG 1.4 Ok
> 5 Centralized Forwarding Card WS-F6700-CFC SAL1336XWTP 4.1
> PwrDown
> 6 Policy Feature Card 3 7600-PFC3CXL SAL153813DT 1.0 Ok
> 6 C7600 MSFC4 Daughterboard 7600-MSFC4 SAL1538AW19 1.5 Ok
>
>
> After a reload with card inserted and powered, the chassis loads to PFC3
> mode.
>
> 7606S-lab#show platform hardware pfc mode
> PFC operating mode : PFC3C
>
> As soon as I remove the card, reload, the chassis loads to PFC3C-XL mode.
> When the card is inserted, it's powered down, to prevent DFC mismatch. Even
> when the DFC and PFC version is the same..both XL.
>
>
> Any thoughts what can be wrong? Other than 'two faulty DFC modules'. As I
> said, both are from different sources and we have used both previously so
> it's really unlikely.
>
>
> Thanks!
>
>
> Jiri
>
>
>
>
>
>
>
> _______________________________________________
> cisco-nsp mailing list cisco-nsp at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-nsp
> archive at http://puck.nether.net/pipermail/cisco-nsp/
>
More information about the cisco-nsp
mailing list