[cisco-voip] CallManager Problem - Make outside call

Kevin Thorngren kthorngr at cisco.com
Tue Apr 11 14:09:00 EDT 2006


Hi Alan,

Does the MGCP GW show registered in CCMAdmin?

Is the voice port on the GW up?

Does "show isdn stat" show "multiple_frame_established"?

Does the CSS of the phone contain the Partition that the Route Pattern 
is in?

You can use "debug mgcp packet" to see if CCM is sending the call via 
MGCP to the GW.

Kevin

On Apr 11, 2006, at 12:55 PM, Alan Su wrote:

> Hi Kevin,
>  
> I tried all those different pattern, but still can't get any response 
> (even the outside dial tone). and I use debug isdn q.921/q.931/event 
> but no see anything in my voice gateway. is it possible that i wrong 
> configure in gateway ? how can I verify is there any signal really 
> comes from CCM to my MGCP gateway? Thanks a lot ~
>  
>  
> Regards,
>  
> Alan
>
>  
> 2006/4/12, Kevin Thorngren <kthorngr at cisco.com>: Hi Alan,
>>
>> I had a typo below.  In the US we would dial 011 for international
>> patterns.  My below example should have had 9.011!.  The "!" allows
>> users to keep dialing digits until the interdigit timeout timer 
>> expires
>> (15 seconds).  You could use the following two patterns:
>>
>> 9.!
>> 9.!#
>>
>> The "#" allows the users to terminate the dialing with a #.  Point 
>> both
>> Route Patterns to the same GW or RL.
>>
>> Once CCM determines the call is an outside call then it will play
>> outside dialtone.  If you don't have any internal patterns that begin
>> with 9 then the users should hear outside dialtone after the 9 is
>> dialed.  The "!" allows them to continue dialing.  In the first 
>> pattern
>> CCM will wait 15 seconds after the last digit (interdigit timeout)
>> before extending the call.  The second pattern allows the user to
>> terminate the dialing with a # and CCM will extend the call right 
>> away.
>>
>> Here is an example of the UK numbering plan.
>> http://www.cisco.com/en/US/partner/products/sw/voicesw/ps556/
>> products_tech_note09186a008028af3a.shtml
>>
>> Kevin
>>
>> On Apr 11, 2006, at 11:42 AM, Alan Su wrote:
>>
>> > Hi Kelvin,
>> >
>> > Thanks a lot, I'll study those valuable documents you share with me.
>> > Regarding the dialing pattern, I also have below questions:
>> > 1. What if I'm in out of US ? Do I still can use @ for typical north
>> > American dial plan ?
>> >
>> > 2. Can user only dial one digit (ex:9), and after hearing the dial
>> > tone then begin to dial the outside number? In this case, I can't 
>> set
>> > the full pattern in my route pattern, how should I configure it ?
>> >
>> > Many many thanks for your help.
>> >
>> >
>>  > Regards,
>> >
>> > Alan
>> >
>> >
>> > 2006/4/11, Kevin Thorngren <kthorngr at cisco.com>: Hi Alan,
>> >>
>> >> The 9. pattern needs to match the full pattern you are using.Some
>> >> examples are:
>> >>
>> >>  9.@ - typical north American dial plan macro that matches local, 
>> ld
>> >> and
>> >> international patterns.
>> >> 9.[2-9]XXXXXX - More specific pattern for local 7 digit dialing
>> >> 9.1[2-9]XX[2-9]XXXXXX - More specific pattern for LD dialing
>> >> 9.011T - More specifc pattern for international dialing
>> >>
>> >> The CCM will need to match the full pattern dialed from the phone
>> >> before extending the call to the GW.With 9. the GW is receiving a
>> >> blank dialed number (assuming you are doing pre-dot discard).Also
>> >> you
>> >> will want to select the option for outside dialtone.The below links
>> >> should help describe this.
>> >>
>> >> http://www.cisco.com/en/US/products/sw/voicesw/ps556/
>> >> products_tech_note09186a0080094b2a.shtml
>> >>
>> >> http://www.cisco.com/en/US/products/sw/voicesw/ps556/
>> >> products_tech_note09186a00800945b9.shtml
>> >>
>> >> http://www.cisco.com/en/US/products/sw/voicesw/ps556/
>> >> products_administration_guide_chapter09186a00803edabe.html
>> >>
>> >>   http://www.cisco.com/en/US/products/sw/voicesw/ps556/
>> >> products_administration_guide_chapter09186a00803ed685.html
>> >>
>> >> HTH,
>> >> Kevin
>> >> On Apr 11, 2006, at 7:47 AM, Alan Su wrote:
>> >>
>> >> > Dear All,
>> >> >
>> >>  > My IPT architecture is: CCM(4.02) + Voice Gateway(3745 runing 
>> MGCP
>> >> w/
>> >> > E1 PRI trunk to PSTN).
>> >> > I already configured the MGCP and ccm-manager option in the voice
>> >> > gateway, and it's registered to CM without any problem.
>> >> > I also made the gateway configuratio in CCM to this router.
>> >> >
>> >> > Right now my problem is, I don't know how to setup the route 
>> pattern
>> >> > to allow IP Phone to make outside call.
>> >> > My idea is, when user dial "9", the phone will provide an outside
>> >> dial
>> >> > tone and user can directly dial the PSTN phone number to 
>> complete a
>> >> > call (just like the old fashion way). But when I configure the 
>> route
>> >> > pattern "9." and set the S1/DS1-0 at VGW to be the gateway, there is
>> >> > nothing but a "Bad Address".
>> >> >
>> >> > Does anyone know how to find the reference document for the
>> >> > configuration or how to fix this problem? I did lots of search 
>> but
>> >> > nothing found. Any comment would be very grateful. Thanks a lot ~
>> >> >
>> >> >
>> >> > Regards,
>> >> >
>> >> > Alan
>> >> > <VGW-Config.txt>_______________________________________________
>> >> > cisco-voip mailing list
>> >> > cisco-voip at puck.nether.net
>> >> > https://puck.nether.net/mailman/listinfo/cisco-voip
>> >>
>>




More information about the cisco-voip mailing list