[cisco-voip] Caller ID

pnowicki at neo.rr.com pnowicki at neo.rr.com
Sat Apr 22 00:50:07 EDT 2006


With this type of setup where you have 2 different ranges of DID (ex. 
701355XXXX and 701250XXXX) like you said, you can not set the calling 
number transformation to a pattern such as these. This is why the 
external phone number mask on the DN pages of the phones are handy. You 
can set those to what ever you would like (usually restricted to phone 
numbers assigned to your PRI group by the carrier)..

Set these to 701355XXXX or what ever you like.. Then on your route 
pattern, check the box for "use external phone number mask" in the 
calling party transformation area. You do not need to set anything more 
in the calling number modification fields... 

If the carrier still sends out the billing number of the PRI's, instead 
of the callerid that you specified, then I would suggest checking out 
your numbering plan and Calling Party number type settings on the PRI 
itself.. The "CallManager" setting basically says that you are using 
the "9.@" route pattern with route filters and for the callmanager to 
apply the number type/plan as recognizes number formats. If it does not 
recognize it, or if you are not using the "9.@" route pattern, then, it 
will send out an "unknown" setting to the carrier for these fields. 
This is usually ok for most purposes, but I find that carriers are more 
and more requiring the numbering type to be set appropriately. I would 
suggest to set the "Calling party IE number type" to ISDN and 
the "Calling Numbering Plan" to National if you are sending out a ten 
digit phone number as the caller id...

Hope this helps...

-Patrick

----- Original Message -----
From: Ward Knutson <ward_knutson at educ8.org>
Date: Friday, April 21, 2006 10:41 am
Subject: [cisco-voip] Caller ID
To: cisco-voip at puck.nether.net

> I recently changed my gateway from a H.323 with 1-T1 PRI to a MGCP 
> with2-T1 PRI's.  The T1's are pooled and I am having trouble 
> passing caller
> ID information on outgoing calls.  Before I was able to set the Caller
> ID DN to 701355XXXX and it worked fine.  Since I have two 
> different set
> of DID's tied to these T1's I can't use the same settings.  I 
> tried 10
> X's and also tried to leave the Caller ID DN blank but then I get the
> number that is associated to the T1 from the service provider.  
> This it
> how I have it set now.
> 
> 
> 
> Calling Line ID Presentation                                Allowed
> 
> Calling Party Selection                                       
> Originator
> Called party IE number type unknown                  Cisco CallManager
> 
> Calling party IE number type unknown                 Cisco CallManager
> 
> Called Numbering Plan                                       Cisco
> CallManager
> 
> Calling Numbering Plan                                      Cisco
> CallManager
> 
> Number if digits to strip                                       1
> 
> Caller ID DN
> 7013553000
> 
> SMDI Base Port                                                 0
> 
> 
> 
> If you have any ideas they would be greatly appreciated.
> 
> 
> 
> 
> 
> Ward Knutson
> 
> Network Coordinator
> 
> Bismarck Public Schools
> 
> Bismarck, North Dakota
> 
> ward_knutson at educ8.org
> 
> 701-355-3037 Office
> 
> 701-527-4034 Cell
> 
> 
> 
> 
> 
> 


More information about the cisco-voip mailing list