[cisco-voip] Setting up local DSP resources on 2821
Ortiz, Carlos
CORTIZ at broward.org
Tue Aug 8 08:39:08 EDT 2006
No, just the PVDM2-32. I'm going to check the DSP calculator next, but
how many DSP's would this config leave me with? Here is the full sh
diag:
Lowrise#sh diag
Slot 0:
C2811 Motherboard with 2FE and integrated VPN Port adapter, 2
ports
Port adapter is analyzed
Port adapter insertion time unknown
EEPROM contents at hardware discovery:
PCB Serial Number : FOC1016457N
Hardware Revision : 1.0
Top Assy. Part Number : 800-26920-01
Board Revision : A0
Deviation Number : 0
Fab Version : 03
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Processor type : 87
Hardware date code : 20060424
Chassis Serial Number : FTX1020A5KQ
Chassis MAC Address : 0017.95aa.9750
MAC Address block size : 24
CLEI Code : CNMJ7P0BRB
Product (FRU) Number : CISCO2811
Part Number : 73-10258-03
Version Identifier : V02
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF C1 8B 46 4F 43 31 30 31 36 34 35 37 4E 40
0x10: 03 E7 41 01 00 C0 46 03 20 00 69 28 01 42 41 30
0x20: 88 00 00 00 00 02 03 03 00 81 00 00 00 00 04 00
0x30: 09 87 83 01 32 19 08 C2 8B 46 54 58 31 30 32 30
0x40: 41 35 4B 51 C3 06 00 17 95 AA 97 50 43 00 18 C6
0x50: 8A 43 4E 4D 4A 37 50 30 42 52 42 CB 8F 43 49 53
0x60: 43 4F 32 38 31 31 20 20 20 20 20 20 82 49 28 12
0x70: 03 89 56 30 32 20 D9 02 40 C1 FF FF FF FF FF FF
PVDM Slot 0:
32-channel (G.711) Voice/Fax PVDMII DSP SIMM PVDM daughter card
Hardware Revision : 4.0
Part Number : 73-8539-05
Board Revision : A0
Deviation Number : 0
Fab Version : 04
PCB Serial Number : FOC101818WH
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Processor type : 00
Product (FRU) Number : PVDM2-32
Version Identifier : V01
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF 40 03 EE 41 04 00 82 49 21 5B 05 42 41 30
0x10: 88 00 00 00 00 02 04 C1 8B 46 4F 43 31 30 31 38
0x20: 31 38 57 48 03 00 81 00 00 00 00 04 00 09 00 CB
0x30: 88 50 56 44 4D 32 2D 33 32 89 56 30 31 20 D9 02
0x40: 40 C1 FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
WIC Slot 0:
FT1 PMC4351
Hardware Revision : 1.2
PCB Serial Number : FOC10173EL3
Part Number : 73-8346-05
Board Revision : A0
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Deviation Number : 0-0
Product (FRU) Number : WIC-1DSU-T1-V2
Top Assy. Part Number : 800-22193-03
CLEI Code : IPUIAPRRAA
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF 40 00 52 41 01 02 C1 8B 46 4F 43 31 30 31
0x10: 37 33 45 4C 33 82 49 20 9A 05 42 41 30 03 00 81
0x20: 00 00 00 00 04 00 80 00 00 00 00 CB 94 57 49 43
0x30: 2D 31 44 53 55 2D 54 31 2D 56 32 20 20 20 20 20
0x40: 20 C0 46 03 20 00 56 B1 03 C6 8A 49 50 55 49 41
0x50: 50 52 52 41 41 FF FF FF FF FF FF FF FF FF FF FF
0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
WIC Slot 1:
T1 (1 port) Multi-Flex Trunk WAN daughter card
Hardware revision 1.0 Board revision B0
Serial number 34799286 Part number 800-03568-04
FRU Part Number VWIC-1MFT-T1=
Test history 0x0 RMA number 00-00-00
Connector type PCI
EEPROM format version 1
EEPROM contents (hex):
0x20: 01 20 01 00 02 12 FE B6 50 0D F0 04 00 00 00 00
0x30: 58 00 00 00 06 04 27 00 FF FF FF FF FF FF FF FF
-----Original Message-----
From: Ted Nugent [mailto:tednugent69 at yahoo.com]
Sent: Monday, August 07, 2006 4:26 PM
To: Ortiz, Carlos; Ryan Ratliff
Cc: Erik Erasmus (E); cisco-voip at puck.nether.net
Subject: Re: [cisco-voip] Setting up local DSP resources on 2821
Are you showing the PVDM2-16 as well?
You can try changing the codec complexity but I
believe this is already the default
voice-card 0
codec complexity flex
Here's a "snippet" from the DSP calc
======================
voice-card 0
codec complexity flex
Set of Conferencing/Transcoding commands when used
with PVDM2-XX DSPs:
sccp local <local interface>
sccp ccm <call manager IP address> identifier <ccm ID
#> version <version #>
sccp
!
sccp ccm group 999
bind interface <local interface>
associate ccm <ccm ID #> priority 1
associate profile <conferencing profile ID #>
register <conference bridge name>
associate profile <transcoding profile ID #>
register <transcoder name>
!
dspfarm profile <transcoding profile ID #> transcode
maximum sessions 4
associate application SCCP
dspfarm profile <conferencing profile ID #> conference
maximum sessions 2
associate application SCCP
====================
--- "Ortiz, Carlos" <CORTIZ at broward.org> wrote:
> In this case I am configuring a 2811 running
> 12.4(9)T. The show diag
> shows me this whick makes sense since I ordered the
> PVDM 16 to 32
> upgrade :
>
> PVDM Slot 0:
> 32-channel (G.711) Voice/Fax PVDMII DSP SIMM
> PVDM daughter card
> Hardware Revision : 4.0
> Part Number : 73-8539-05
> Board Revision : A0
> Deviation Number : 0
> Fab Version : 04
> PCB Serial Number : FOC101818WH
> RMA Test History : 00
> RMA Number : 0-0-0-0
> RMA History : 00
> Processor type : 00
> Product (FRU) Number : PVDM2-32
>
> I was able to create the profiles for conferencing
> and transcoding. I
> am able to put max sessions for transcoding to 4,
> but I am not able to
> select anything but 0 for conf. see below:
>
> Lowrise(config)#dspfarm profile 1 conference
> Lowrise(config-dspfarm-profile)#maximum sessions ?
> <0-0> Number of sessions assigned to this profile
>
> I have a T1 WIC and a T1-1MFT card in the router but
> not sure why I
> can't select sessions for the conf br.
>
> Any clues would be appreciated.....
>
>
> -----Original Message-----
> From: Ted Nugent [mailto:tednugent69 at yahoo.com]
> Sent: Monday, August 07, 2006 2:45 PM
> To: Ryan Ratliff; Ortiz, Carlos
> Cc: Erik Erasmus (E); cisco-voip at puck.nether.net;
> Ted Nugent
> Subject: Re: [cisco-voip] Setting up local DSP
> resources on 2821
>
> You also need to configure your devices in CM as
> "Enhanced IOS devices" in case thats not clear in
> the
> doc.
>
> --- Ryan Ratliff <rratliff at cisco.com> wrote:
>
> > The PDVM2s require the dspfarm profile
> > configuration. Yes you do
> > have to associate the profile to a sccp ccm group.
> >
> > -Ryan
> >
> > On Aug 7, 2006, at 2:12 PM, Ortiz, Carlos wrote:
> >
> > This is a response to a 3 week old post. Did you
> > guys ever get this
> > working? I am reading through the documentation
> and
> > it's a bit
> > confusing. You guys posted part of a config below,
> > but I am reading and
> > they mention Associating a DSP Farm Profile to a
> > Cisco Unified
> > CallManager Group. Did you have to do this?
> >
> > Which example would you follow for onboard ISR
> > 28XX/38xx router PVDM2
> > configuration??
> >
> > Carlos
> >
> > -----Original Message-----
> > From: cisco-voip-bounces at puck.nether.net
> > [mailto:cisco-voip-bounces at puck.nether.net] On
> > Behalf Of Erik Erasmus
> > (E)
> > Sent: Tuesday, July 18, 2006 3:55 PM
> > To: Wydra, Jason; Ted Nugent;
> > cisco-voip at puck.nether.net
> > Subject: Re: [cisco-voip] Setting up local DSP
> > resources on 2821
> >
> >
> > I was wondering about the same thing
> >
> > I will have a PVDM2-8 for normal termination of
> the
> > BRIs and probably
> > a PVDM2-32 for the conferencing /transcoding
> >
> >
> >
> > Erik Erasmus
> >
> >
> > -----Original Message-----
> > From: cisco-voip-bounces at puck.nether.net
> > [mailto:cisco-voip-bounces at puck.nether.net] On
> > Behalf Of Wydra, Jason
> > Sent: 18 July 2006 09:46 PM
> > To: Ted Nugent; cisco-voip at puck.nether.net
> > Subject: Re: [cisco-voip] Setting up local DSP
> > resources on 2821
> >
> > One more thing with the following....
> >
> > voice-card 0
> > dspfarm
> > dsp services dspfarm
> >
> > If I run a show diag, I see two PVDM2-32 modules.
> > One is slot 0 and
> > the
> > other is slot 1. Does the voice-card command above
> > denote the actual
> > slot number of the PVDM? Reason I ask is because I
> > want the PVDM in
> > slot
> > 0 to do transcoding and the PVDM in slot 1 to do
> > conferencing. When I
> > try to configure the following I get this:
> >
> > ft-worth(config)#voice-card 1
> > ^
> > % Invalid input detected at '^' marker.
> >
> > ft-worth(config)#voice-card ?
> > <0-2> Voice interface slot #
> >
> > ft-worth(config)#voice-card
> >
> >
> > Thanks,
> > Jason
> > -----Original Message-----
> > From: Ted Nugent [mailto:tednugent69 at yahoo.com]
> > Sent: Tuesday, July 18, 2006 12:46 PM
> > To: Wydra, Jason; cisco-voip at puck.nether.net
> > Subject: Re: [cisco-voip] Setting up local DSP
> > resources on 2821
> >
> > You need it all... confusing at first but after
> you
> > set it up a couple times it's not so bad.
> >
> > Makes me miss the old NM-HDV config :-/
> >
> >
>
http://www.cisco.com/univercd/cc/td/doc/product/software/ios123/123cgc
> > r/
> > vvfax_c/callc_c/ccm_c/intcnf2.htm#wp1061433
> >
> > voice-card 0
> > dspfarm
> > dsp services dspfarm
> > !
> > !
> > sccp local FA0/0
> > sccp ccm <pub-ipaddr> identifier 2 version 4.0
> > sccp ccm <sub-ipaddr> identifier 1 version 4.0
> > sccp ip precedence 3
> > sccp
> > !
> > sccp ccm group 1
> > associate ccm 2 priority 2
> > associate ccm 1 priority 1
> > associate profile 2 register <site>xcode
> > associate profile 1 register <site>conf
> > keepalive retries 5
> > switchover method immediate
> > switchback method immediate
> > switchback interval 15
> > !
> > dspfarm profile 2 transcode
> > codec g711ulaw
> > codec g711alaw
> > codec g729ar8
> > codec g729abr8
> > codec gsmfr
> > maximum sessions 12
> > associate application SCCP
> > !
> > dspfarm profile 1 conference
> > codec g711ulaw
> > codec g711alaw
> > codec g729ar8
> > codec g729abr8
> > codec g729r8
> > codec g729br8
> > maximum sessions 8
> > associate application SCCP
> >
> >
>
=== message truncated ===
__________________________________________________
Do You Yahoo!?
Tired of spam? Yahoo! Mail has the best spam protection around
http://mail.yahoo.com
More information about the cisco-voip
mailing list