[cisco-voip] CME: Ad-Hoc Multiparty Conferencing Problem

[Ramiz Sardar]

Hi,

I am trying to configure DSPFarm for ad-hoc multiparty conferencing as per
documentation but when i try to configure maximum session in "dspfarm
profile 2 conference", the available value is just 0. and when i execute sh
dspfarm all command, the output you can see below:

CME#sh dspfarm all
Dspfarm Profile Configuration

Profile ID = 2, Service = CONFERENCING, Resource ID = 1
Profile Description :
Profile Admin State : DOWN
Profile Operation State : DOWN
Application : SCCP Status : NOT ASSOCIATED
Resource Provider : FLEX_DSPRM Status : NONE
Number of Resource Configured : 0
Number of Resource Available : 0
Codec Configuration
Codec : g711ulaw, Maximum Packetization Period : 30 , Transcoder: Not
Required
Codec : g711alaw, Maximum Packetization Period : 30 , Transcoder: Not
Required
Codec : g729ar8, Maximum Packetization Period : 60 , Transcoder: Not
Required
Codec : g729abr8, Maximum Packetization Period : 60 , Transcoder: Not
Required
Codec : g729r8, Maximum Packetization Period : 60 , Transcoder: Not Required

Codec : g729br8, Maximum Packetization Period : 60 , Transcoder: Not
Required

Total number of DSPFARM DSP channel(s) 0

CME#sh inventory
NAME: "2811 chassis", DESCR: "2811 chassis"
PID: CISCO2811 , VID: V05 , SN: FCZ120872XE

NAME: "WAN Interface Card - Serial (1T) on Slot 0 SubSlot 0", DESCR: "WAN
Interface Card - Serial (1T)"
PID: WIC-1T= , VID: 1.0, SN: 36242834

NAME: "VWIC2-1MFT-T1/E1 - 1-Port RJ-48 Multiflex Trunk - T1/E1 on Slot 0
SubSlot 1", DESCR: "VWIC2-1MFT-T1/E1 - 1-Port RJ-48 Multiflex Trunk - T1/E1"

PID: VWIC2-1MFT-T1/E1 , VID: V01 , SN: FOC12122L32

NAME: "2nd generation four port FXO voice interface daughtercard on Slot 0
SubSlot 2", DESCR: "2nd generation four port FXO voice interface
daughtercard"
PID: VIC2-4FXO , VID: V03 , SN: FOC12081UJ3

NAME: "PVDMII DSP SIMM with one DSP on Slot 0 SubSlot 4", DESCR: "PVDMII DSP
SIMM with one DSP"
PID: PVDM2-16 , VID: V01 , SN: FOC11525U28

NAME: "PVDMII DSP SIMM with one DSP on Slot 0 SubSlot 5", DESCR: "PVDMII DSP
SIMM with one DSP"
PID: PVDM2-16 , VID: V01 , SN: FOC12085AAK

NAME: "AIM Service Engine 0", DESCR: "AIM Service Engine"
PID: AIM-CUE , VID: V03 , SN: FOC12043MQE

If you think there is any problem with configuration, please write down
sample steps for Ad-Hoc Conferencing for more then 3 participants.
Waiting for immediate response

Note: i am using CME on cisco 2811 with ios
c2800nm-spservicesk9-mz.124-15.T5.

Waiting for your immediate response

Best Regards
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://puck.nether.net/pipermail/cisco-voip/attachments/20080705/b122995a/attachment.html>